SpringCard CRAZYWRITER User manual

PMU8B5P-AB
1 / 2
CRAZYWRITER - Hardware manual
www.springcard.com
Headquarters, Europa
SpringCard
13 Vo e la Cardon
Parc Gutenberg
91120 Pala seau
FRANCE
Phone : [phone]
Fax : [phone]
Americas
SpringCard
694 F fth Avenue
Su te 235
San D ego, CA 92101
USA
Phone : [phone]
Fax : [phone]
EDITOR’S INFORMATION
PRO ACTIVE SAS company w th a cap tal of 227 000 €
RCS EVRY B 429 665 482
Parc Gutenberg, 13 vo e La Cardon
91120 PALAISEAU FRANCE
Copyr ght © PRO ACTIVE SAS 2009, all r ghts reserved.
SPRINGCARD, the SPRINGCARD logo, PRO ACTIVE and the PRO ACTIVE logo are reg stered trademarks of PRO ACTIVE SAS. All other brand names, product names, or
trademarks belong to the r respect ve holders. Informat on n th s document s subject to change w thout not ce. Reproduct on w thout wr tten perm ss on of PRO ACTIVE s forb dden.
C RAZY W RITER
Hardware manual
Thank you for choosing SpringCard !
CrazyWr ter s an OEM contactless smartcard reader,
w th 2 µSIM/SAM slots.
Thanks to ts nat ve USB nterface, CrazyWr ter s
PC/SC compl ant. The dev ce may also be operated n
legacy mode, e ther on USB or n RS-232 thanks to
an opt onal nterface board.
Th s document s the reference gu de to nstall
CrazyWr ter n your equ pment.
M OUNTING FOR USB OPERATION
 Install Crazy riter Mother Board (EASD470) n a
place where you can access the µSIM/SAM slots
and the USB connector eas ly.
 Install the antenna (e ther Crazy riter Standard
Antenna EASD471 or any compl ant antenna
1
)
near the “land ng zone” of the contactless
smartcards (d stance between the smartcard and
the antenna must be 0,5cm ≤ d ≤ 1,5cm for
correct operat on w th most smartcards).
 Connect the antenna to the mother board :
• Short d stance (d ≤ 5cm) : use a 2-w re
tw sted cable (J4 connector)
• Long d stance (5cm ≤ d ≤ 200cm) : use a
50Ω coax al cable.
J3
USB
P2 J2
J4
J1
Min
20,00mm
JP1
Drawing not to scale
Antenna
EASD471
Mother board
EASD470
1
Spr ngCard offers var ous antennas, w th d fferent s zes to
accommodate most needs. We also offer a custom des gn serv ce.
Don’t hes tate to contact us f you need a spec f c antenna.
M OUNTING FOR RS-232 OPERATION
 Install Mother Board and Antenna follow ng the
steps dep cted n the prev ous paragraph.
 Install the Power+RS232 board (EASD472)
 Connect P1A to P2 us ng the 8-w re cable.
J1 P1
P1A
Power+RS232
EASD472
(opt on CW-RS)
An external power supply s requ red n th s
conf gurat on (9 – 12V DC, 500mA)
Use only the prov ded 8-w re cable (20cm approx.).
U SING THE µSIM/SAM SLOTS
Install one or two µSIM/SAM s SC2 and SC3.
• SC2 s “slot 2” n legacy mode (Spr ngProx API), and
“CrazyWr ter SAM 1” n PC/SC.
• SC2 s “slot 3” n legacy mode (Spr ngProx API), and
“CrazyWr ter SAM A” n PC/SC.
S1
SW1
SC2 SC3
Drawing not to scale
Use JP1 to select the µSIM/SAM voltage as follow :
J3
USB
JP1
µSIM/SAM voltage selection
5V 3.3V
Note that both slots operate at the same voltage.

PMU8B5P-AB
2 / 2
CRAZYWRITER - Hardware manual
Copyr ght © PRO ACTIVE SAS 2009, all r ghts reserved.
SPRINGCARD, the SPRINGCARD logo, PRO ACTIVE and the PRO ACTIVE logo are reg stered trademarks of PRO ACTIVE SAS. All other brand names, product names, or
trademarks belong to the r respect ve holders. Informat on n th s document s subject to change w thout not ce. Reproduct on w thout wr tten perm ss on of PRO ACTIVE s forb dden.
C ONFIGURING THE SWITCHES
S1
Use a th n screw-dr ver or a sharp
object to conf gure S1 as follow :
1 2 3 4
USB PC/SC or Legacy
2
ON OFF ON OFF
Ser al
ON OFF OFF ON
USB Flash mode
ON ON ON ON
USB Test mode
ON OFF ON ON
DO NOT select the greyed conf gurat ons (last 2
l nes) n normal operat on.
I NSTALLING THE DRIVER AND
CONNECTING THE PRODUCT
USB operation
Follow the CSB6 Family Quick Installation Guide
(PMUJ5P) to nstall the dr ver before connect ng the
CrazyWr ter to your computer.
Do not connect the Power+RS232 board (EASD472)
when operat ng CrazyWr ter on USB
PC/SC dr ver for CSB6 Fam ly s ava lable at :
www.spr ngcard.com/download/dr vers.html
For non-W ndows OS, please read :
www.spr ngcard.com/support/pcscl te.html
Serial operation with Power+RS232 Board
 Connect the Power+RS232 board to the
CrazyWr ter mother board us ng the 8-w re
cable.
 Use a DB-9 cable, cert f ed for RS-232 (not
prov ded), to connect the Power+RS232 to the
computer (P1 connector).
 Use a 9V to 12V DC power supply, 500mA m n.
(not prov ded) to power the Power+RS232 board
(J1 jack).
2
Cho ce between PC/SC and Legacy mode s made by non-volat le
software conf gurat on. The procedure s dep cted at
www.spr ngcard.com/support/csb6legacy.html
Serial operation using a custom cable
A custom cable can be manufactured for ser al
operat on d rectly on CrazyWr ter mother board (P2)
P2 1
TX-RX are RS232 level (+12 / -12 V)
VCC = 5V ±10% - 500mA
For correct operat on, do not use a cable longer than
20cm.
PINOUT P2
CrazyWr ter mother board
(EASD470)
P1A
Power+RS232 board
(EASD472)
location name type name type
1 GND
Ground
GND
Ground
2 CW TX
Out
PC RX
In
3 CW RX
In
PC TX
Out
4 VCC
Power n
VCC
Power out
5 _RESET
In
Not connected
6 GND
Ground
GND
Ground
7 _FLASH
In
Not connected
8 Not connected Not connected
_RESET : Act ve low. If not used, leave th s p n
unconnected, or pulled up to VCC by a 10K res stor.
_FLASH : Used to upgrade the f rmware (Act ve low). In
normal operat on, leave th s p n unconnected, or pulled up
to VCC by a 10K res stor.
You must reset the dev ce after chang ng _FLASH p n level
(apply a low pulse on _RESET, or cycle power).
SDK for CrazyWriter
Go to
www.spr ngcard.com/download/sdks.html
For PC/SC operat on, choose :
SDK PC/SC : sample software and documentat on
For Legacy operat on on W ndows, choose :
SDK for CSB class c and legacy
For Legacy operat on on another OS or w thout OS,
choose : SDK K531