Triton 9600 EMV User manual

9600 EMV UPGRADE KIT
FIELD INSTRUCTIONS
TDN 07103-00247 June 30, 2014
COPYRIGHT NOTICE
© 2014 Triton. All Rights Reserved. TRITON logo is a
registered trademark of Triton Systems of Delaware, LLC
Corporate Headquarters
21405 B Street
Long Beach, MS 39560
Phone: [phone]
Fax: [phone]

2
9600 EMV UPGRADE KIT INSTALLATION
Document Updates
June 30, 2014 Original

3
FIELD UPGRADE INSTRUCTIONS
REQUIRED PARTS AND TOOLS
TOOLS REQUIRED 2 x #2 Phillips screwdriver (Stubby and standard)
7/16 open end wrench
Small needle nose pliers
ESD wrist strap with grounding cord
KIT 06200-00252 EMV ICM330 Card Reader Upgrade Kit for 9600 - US Only
Description Qty
Sankyo 330 EMV Card Reader 1
Sankyo ICM330 Card Reader Data Cable 1
8 inch Braid Ground Cable 2
#6 x 3/8 Phillips Drive Pan Plastite Mounting Screw 4
#8 x 32 - 3/8 Long Standoff 1
Threaded #8 - 32 Thread Snap-in Insert 1
#8 x 32 - 3/8 Long Screw 1
Sankyo EMV Installation
** IMPORTANT **
If the unit intended for upgrade has a Quad-Port Module
with one of the following part numbers, the module is NOT
compatible with the EMV upgrade and must be upgraded.
09600-02030
09600-01013
These boards do not have a +12v port available.

4
9600 EMV UPGRADE KIT INSTALLATION
1. Put the ESD wrist strap on and attach the cord to the ground.
2. Unlock and open the upper portion of the cabinet.
3. Flip the switch on the power supply to the OFF (O) position.
4. Unplug the card reader data cable from the PCI SPED Adapter Board.
Removing the old Card Reader
5. While holding the card reader from the front of the control panel, remove the 4 screws that secure it
in place. Remove the card reader and card reader data cable.

5
FIELD UPGRADE INSTRUCTIONS
5. Remove the screw securing the unit ground wire to the control panel. Discard the screw.
View from Front of Unit
(Triton logo correctly oriented)
Installing the Sankyo EMV 330 Card Reader
1. Put the ESD wrist strap on and attach the cord to the ground.
2. Unlock and open the upper portion of the cabinet.
3. Flip the switch on the power supply to the OFF (O) position.
4. Insert the EMV card reader from the front of the unit. Secure the card reader in place with the 4 screws
supplied.

6
9600 EMV UPGRADE KIT INSTALLATION
6. Obtain the EMV card reader data cable. Ensure the cable locking tabs on the card reader are in the
unlocked position (out). Plug the cable into the card reader. As the cable is inserted into the port, the
locking tabs will close over the cable securing it in place.
7. Open the four cable clips (yellow arrows). Route the card reader cable (red arrows) under the printer
powercable(greenarrow) andthrough thefour cableclips asshown. Close theclips tosecure thecables.

7
FIELD UPGRADE INSTRUCTIONS
8. Plug the EMV card reader cable into the module. If the module is a Multi-Function board with part
numbers 09110-00414 or 09110-01414, plug the card reader cable into the port labeled “Reader”.
If the module is a Quad-Port module with part numbers 09600-00020 or 09600-00044, set the JP5 jumper
to “Aux (2)” position and the JP3 jumper to the “+12v” position. Plug the card reader cable into the
“Serial 3”port.
If the module is a Tri-Port module with part number 09110-00235, set the J4 jumper to the “+12v” position.
Plug the card reader cable into the “Serial 3” port.

8
9600 EMV UPGRADE KIT INSTALLATION
9. Unlock and pull out the Memory Module board. Ensure the EPROM chip is version SD04.00 or higher
to be compatible. (Updated EPROM chips are available on www.ATMGurus.com.)
10. Obtain one ground cable. Remove one of the nuts securing the control panel bracket. Install one end
of the ground cable onto the post and reinstall the nut.

9
FIELD UPGRADE INSTRUCTIONS
11. Obtain the 3/8 standoff, threaded snap-in insert & the 3/8 long screw. Install the threaded snap-in insert
into the control panel. Screw the stand off into the snap-in insert as shown.
12. Install the three ground cables onto the 3/8 long screw as shown and install the screw into the insert
previously installed.

10
9600 EMV UPGRADE KIT INSTALLATION
13. Obtain the second ground cable. Remove the bolt and washer along the rear wall in the rear right
corner. Install the ground wire under the washer and reinstall the bolt into the cabinet. Remove the
screw from the card cage and secure the other end of the ground cable as shown.
14. With the unit’s power still OFF, check the resistance of the grounded points. Place one ohmmeter probe
on the screw securing the ground cable to the card cage and place the other probe on the screw securing
the unit’s three ground cables to the control panel. The resistance should measure less than 1 ohm.