SSANGYONG Korando 2010 User manual

GENERAL INFORMATION
0000-00
GENERAL INFORMATION
GENERAL INFORMATION
1. MAJOR DIMENSION..............................
2. VEHICLE IDENTIFICATION....................
3. EXTERIOR LAMP SYSTEM LAYOUT....
4. INTERIOR LAMP SYSTEM LAYOUT.....
5. SWITCH SYSTEM LAYOUT...................
6. CAN COMMUNICATION
CONFIGURATION..................................
2
2
3
5
6
7
ELECTRIC DEVICE GENERAL INFORMATION
1. HOW TO READ ELECTRICAL WIRING
DIAGRAM...............................................
2. HOW TO CHECK TERMINAL NUMBER
OF CONNECTOR...................................
3. PART LOCATION ACCORDING TO
CONNECTOR NUMBER.........................
8
10
11

01-2
undefined
0000-00
GENERAL INFORMATION
3) The certification label is affixed on the
bottom of driver side B-pillar. (30 psi)
2) The chassis number
(KPTA0B1SSAP012345) is stamped on the
right side in the engine compartment
(passenger side).
1) The engine number (671 950 0 2
5000001) is stamped on the lower area of
cylinder block in exhaust manifold side.
1. MAJOR DIMENSION
GENERAL INFORMATION
2. VEHICLE IDENTIFICATION
Top View
Side View
Front view Rear view

01-3
GENERAL INFORMATION
undefined
0000-00
Front turn signal lamp
Side repeater lamp
Puddle lamp
3. EXTERIOR LAMP SYSTEM LAYOUT
Front fog lamp
Position lamp
Headlamp assembly
Backup lamp
High-mounted stop
lamp
Tail/stop lamp
Reflector
Rear turn signal lamp
Tail lamp
License plate lamp
Front view Rear view

01-4
undefined
0000-00
GENERAL INFORMATION
High mounted stop lamp
Rear combination lamp
Puddle (approach) lamp
High-beam/low-beam
Turn signal lamp
Position lamp
1.
2.
3.
Stop lamp and tail lamp
Turn signal lamp
Backup lamp
Stop lamp (For Korea)
Rear fog lamp
1.
2.
3.
4.
Vehicle without
spoiler
Vehicle with spoiler
License plate lamp
Headlamp
Front fog lamp
Side repeater lamp

01-5
GENERAL INFORMATION
undefined
0000-00
Front room lamp Sun visor lamp
4. INTERIOR LAMP SYSTEM LAYOUT
Glove box lamp
Door courtesy lamp
Luggage lamp
Center room lamp

01-6
undefined
0000-00
GENERAL INFORMATION
Driver power seat
switch
Rear door switch (LH)
Tailgate switch
Luggage lamp switch
Center room lamp
switch
Rear door switch (RH)Front seat heated wire
switch (STD)
Front seat heated wire
switch (DLX)
Drive door main switch &
Outside rear view mirror
switch
Passenger door
switch
Steering wheel remote
control switch
Lower main panel
switch
Overhead console
switch
Cruise control switch
Hazard warning switch and
bezel assembly
Multifunction switch
FATC switch
5. SWITCH SYSTEM LAYOUT

01-7
GENERAL INFORMATION
undefined
0000-00
6. CAN COMMUNICATION CONFIGURATION
There are two types (P-CAN and B-CAN) of communication according to the communication
speed. The instrument cluster and BCM (Body Control Module) communicate through both P-
CAN and B-CAN at the same time.
1) CAN Configurations (P-CAN/B-CAN)
Abbreviations Meaning Function
GCU Glow Control Unit Glow control unit
EPS Electronic Power Steering Unit Electrically driven power steering unit
BCM Body Control Module Body control module
2) CAN Communication Wiring Diagram
Splice pack Wiring Location
S101 Floor wiring (LH) Under fuse and relay box in engine
compartment
S102 Floor wiring (RH) Inside of right fender
S201 Main wiring Behind the instrument cluster
(cowl cross member)
S202 Main wiring Behind the instrument cluster
(cowl cross member)
S205 Floor wiring (LH) Under driver door scuff

01-8
undefined
0000-00
GENERAL INFORMATION
ELECTRIC DEVICE GENERAL INFORMATION
1. HOW TO READ ELECTRICAL WIRING DIAGRAM
(1) HOW TO READ ELECTRICAL WIRING DIAGRAM

01-9
GENERAL INFORMATION
undefined
0000-00
(2) CONTENTS OF ELECTRICAL WIRING DIAGRAM(CIRCUIT)
(3) CIRCUIT IDENTIFICATION SYMBOL
(4) FUNCTION OF POWER SUPPLY LINE(NUMBER)
(5) WIRING HARNESS COLOR IDENTIFICATION
Position Emplanation
A A top of horizontal line means Power supply and it is separated depending on
condition of power supply. (For more information, please refer to the Function of
power supply No.appendix)
B This means Blow-slow Fuse No.8 in an Engine Room Fuse-Box and it is Main
Fuse which supplies the power to each Fuse.
C These mean both a Fuse No. and a Fuse location. And Ef means an Engine
Room Fuse, F means an indoor Fuse. 7.5A means Fuse capacity.
D S means Splice Pack and 206 means Splice Pack Number.
E C means Connector and '208' means Connector Number.
F This means inner circuit and it is displayed one-point-center-line.
G This means wiring color, so at the head of character Y means background color
of wiring and the rear character R means middle color of wiring.
H G means Ground and 203 means Ground Number.
I Below horizontal line means Ground.
-Ground position (G101~G401)
-B : Body Ground
Identification Symbol Meaning
C Connector
D Diode
Ef Fuse in Engine room Fuse & Relay Box
F Indoor Fuse Box
G Ground
S Splice pack (Junction connector)
SB1 ~ SB10 Slow Blow Fuse (Engine room fuse & relay Box)
Power supply NO. Power supply condition
15 Battery Voltage (B+) Supply in Ignition Switch ON and ST (IGN 1)
15A Battery Voltage (B+) Supply in Ignition Switch ON (IGN 2)
15C Battery Voltage (B+) Supply in Ignition Switch ACC (ACC)
30 Battery Voltage (B+) Supply directly regardless of Ignition Switch
31 Ground Connnected to Battery(-)
50 Battery Voltage (B+) Supply in Ignition Switch ST
58 Battery Voltage (B+) Supply in Head Lamp Switch 1st and 2nd
step(Illumination circuit)
Abbreviation Color Abbreviation Color
Br Brown Sb Sky Blue
G Green R Red
V Violet L Blue
P Pink Y Yellow
W White Gr Gray
O Orange B Black
Lg Light Green
" "
" "
" "
" " ' '
' '
' '
' '
' '
" " " "
" "
" "
" "

01-10
undefined
0000-00
GENERAL INFORMATION
(6) ELECTRIC SYMBOLS 2. HOW TO CHECK TERMINAL NUMBER OF CONNECTOR
Terminal number is given based on Female Terminal Male Connector
▶
ex) Terminal Number 4 of C901 connection-
Terminal number of Connector
▶
Generally, the Connector terminal number is given from left to right direction of Locking upper
position through the Female Terminal.
Exceptionally, Control unit such as Engine ECU, TCU and Instrument Cluster was used a
specific number which marked on the draft.
If a lot of connectors was connected to one parts, the connector was marked as A, B, C in
front of terminal number.
In case of terminal number was carved into connector or each parts, we will use the carved
number exceptionally.
-
-
-
-

01-11
GENERAL INFORMATION
undefined
0000-00
3. PART LOCATION ACCORDING TO CONNECTOR NUMBER
C : Symbol Character for Connector ex) C102
▶
1 : Connector location Number
▶
Connector Number according to locating Section
▶
In the locating section, the assignment for part number startsfrom left bottom and proceeds
clockwise.
In the fuse and relay box or the instrument panel, the partnumber is assigned from left top to
light bottom.
-
-
02 : Connector Numbering Order
▶
Symbol Character Description
C Connector (Connecting part that connects two wiring harness)
D Diode
G Ground
SSplice pack (Joint connector that connects various wiring harness)
Connector Number Location
□1□□ Engine Compartment
□2□□ Instrument panel
□3□□ In Door
□4□□ Tail Gate
□9□□ Under Body

CONNECTOR/GROUND
1413-02/8210-00/8210-01/8211-01/8212-01/8212-02
/8213-03/8213-04/8213-06/8213-09/8213-108810-22/8810-23
CONNECTOR/GROUND
WIRING HARNESS
8210-00 WIRING HARNESS,
COMPONENTS LOCATION.......
8210-00 CONNECTOR, GROUND /
SPLICE PACK............................
2
4
CONNECTOR/GROUND
8210-01 W/H MAIN..................................
8212-01 W/H FLOOR(LH)........................
8212-02 W/H FLOOR(RH)........................
1413-02 W/H ENGINE MAIN.....................
8211-01 W/H ENGINE EXTN.....................
8213-09 W/H ROOF.................................
8810-22 W/H AIR BAG............................
8810-23 W/H AIR BAG EXTN...................
8213-03 W/H DRIVER DOOR...................
8213-04 W/H PASSENGER DOOR...........
8213-06 W/H REAR DOOR......................
8213-10 W/H TAIL GATE.........................
11
13
15
16
17
18
19
19
20
20
21
21

02-2
undefined
8210-00
CONNECTOR/GROUND
WIRING HARNESS
(1) WIRING HARNESS
8210-00 WIRING HARNESS, COMPONENTS LOCATION

02-3
CONNECTOR/GROUND
undefined
8210-00
(2) COMPONENTS LOCATION

02-4
undefined
8210-00
CONNECTOR/GROUND
CONNECTOR
▶
GROUND
▶
SPLICE PACK
▶
8210-00 CONNECTOR, GROUND / SPLICE PACK
(1) CONNECTOR, GROUND, SPLICE PACK

02-5
CONNECTOR/GROUND
undefined
8210-00
1) S101 (HS-CAN)
(2) SPLICE PACK CIRCUIT
2) S102 (HS-CAN)
3) S201 (LS-CAN)
4) S202 (HS-CAN)
5) S203 (ILL+)

02-6
undefined
8210-00
CONNECTOR/GROUND
6) S204 (GND)
7) S205 (HS-CAN)
8) S301

02-7
CONNECTOR/GROUND
undefined
8210-00
(3) WIRING CONNECTOR PARTS SHAPE / NUMBERING

02-8
undefined
8210-00
CONNECTOR/GROUND
(4) THE OTHERS PARTS SHAPE / NUMBERING
UNIT PART
▶SWITCH PART ▶

02-9
CONNECTOR/GROUND
undefined
8210-00
MOTOR PART
▶
LAMP PART
▶
SENSOR PART
▶