SSI Fluid – Trac DFT – 110 Installation and operating instructions

SSI TECHNOLOGIES, INC.
Controls Division
2643 W. Court Street
Janesville, WI 53548-5011
Phone: [phone] Fax: [phone]
www.ssitechnologies.com
Page
1
Copyright 12/23/09
SSI Technologies Inc.
All Rights Reserved
Revision 1
RoHS
SSI Technologies - Application Note DT-AN5
Digital Fluid – TracTM (DFT – 110) Multi-Unit Drum Gauge
Product Overview
Product Description
Digital Fluid-Trac™ Model DFT-110 multi unit drum
level gauge is a cost competitive non-contact liquid
level drum gauge. The DFT-110 drum gauge was
designed for usage on ANSI MH2-2004 vertical
drums (≤ 32 inch depths). The DFT -110 drum
gauge allows the user to easily select between the
following vertical drum settings:
•15 gallon
•30 gallon
•55 gallon
•57 liter
•114 liter
•208 liter
Product Features
•Multiple Selectable Units: 15, 30, 55 gallons
or 57, 114, 208 liters
•Resolution: +/- 0.5 gallon or +/- 1 liter*
•Accuracy: +/-2% of full scale volume (based on
55 gal / 208 liter setting) *
•Automatic Shutoff To Prolong Battery Life
•NEMA 4 Packaging
•Static Display Useful for Usage Consumption
Calculations: The static level reading can be
used for manual rate calculations – i.e. daily or
weekly consumption.
•Low Level Warning Light: A red LED will flash
once every second when the volume is at 10%
or below the maximum volume.
•Easy to install: Digital Fluid-Trac™ DFT-110
has no components to protrude into the drum.
•Standard: Fits 2” NPT or ¾” NPS opening
•Dead Band: 6” from top of barrel when using
the optional ¾” adaptor
•More Reliable: No components to chemically
corrode inside liquid media.
•Chemical compatibility: Digital Fluid-Trac™
DFT-110 drum gauge works with a wide variety
of media such as water, waste water, motor oil,
hydraulic fluid and diesel fuel.
* Outside of stated dead band.
The Digital Fluid-Trac™ DFT-110 drum level gauge
is NOT intended for use with gasoline.
SSI can customize the drum level gauge for other
sizes for large volume OEM orders.
Contact SSI Technologies at [phone].
Press and release
Refresh/Select to update
the level reading and select
display units
Low Level
Warning

SSI TECHNOLOGIES, INC.
Controls Division
2643 W. Court Street
Janesville, WI 53548-5011
Phone: [phone] Fax: [phone]
www.ssitechnologies.com
Page
2
Copyright 12/23/09
SSI Technologies Inc.
All Rights Reserved
Revision 1
RoHS
SSI Technologies - Application Note DT-AN5
Digital Fluid – TracTM (DFT – 110) Multi-Unit Drum Gauge
Product Overview
Measurement Technology
The Digital Fluid-Trac™ DFT-110 drum level gauge
uses ultrasonic technology to generate a high-
frequency sound wave and measures the time for
the echo to reflect off the target fluid’s surface and
return. The distance from the Digital Fluid-Trac’s
sensor to the liquid is calculated based on the
speed of sound.
The Digital Fluid-Trac™ DFT-110 has a LCD which
displays the liquid level pictorially as well as in
gallon (or liter) units. The display shows the level
reading from the last time the Refresh/Select button
was pressed.
When the Refresh/Select button is pressed and
released, the DFT-110’s back-light is illuminated
and 8.8.8. is displayed for 4 seconds to indicate the
unit is in test mode. The unit continuously monitors
the media in the vertical drum for 7 seconds and
then displays the liquid level. The level reading will
remain static until the Refresh/Select button is
depressed again.
20 seconds after the button was pressed, the unit
will go into a battery saver mode where the back-
light is shut off. The liquid level reading will be
displayed for 5 minutes before the display turns off.
.
A low level warning light (red LED located on the
bottom left of the LCD display), will flash once every
second when the liquid level is <= 10% the
maximum volume. Note: This warning light does
not operate once the unit has powered down in
battery saver mode.
Electrical Interface
The Digital Fluid-Trac™ DFT-110 drum gauge is
powered by two 9 volt batteries (not included). The
unit can run on alkaline or lithium batteries.
If the battery life is low (voltage is below 14.2 volts),
“LoB “will continuously flash to notify the user to
replace the batteries.
Displaying the DFT-110 Setting
a) Press and hold the Refresh/Select
button down for 7 seconds. The
drum size will be displayed. And the
selected units (Liter or Gallon) will
be flashing.
b) Release the Refresh/Select button
and the unit will automatically go
back into test mode (indicated by
8.8.8) in 20 seconds.
Selecting the Display Units
The Digital Fluid-Trac™ DFT-110 multi-unit
drum gauge can set to display the level
reading in one of six different configurations -
gallons (15, 30, 55) or liters ( 57, 114, 208 ).
a) Enter the Select Mode: Press and
hold the Refresh/Select button down for 7
seconds to enter the Select Mode. The
unit will display Liter and Gallon. One of the
units will be flashing.
Note: If you release the button too
soon, the DFT-110 will be in test mode.

SSI TECHNOLOGIES, INC.
Controls Division
2643 W. Court Street
Janesville, WI 53548-5011
Phone: [phone] Fax: [phone]
www.ssitechnologies.com
Page
3
Copyright 12/23/09
SSI Technologies Inc.
All Rights Reserved
Revision 1
RoHS
SSI Technologies - Application Note DT-AN5
Digital Fluid – TracTM (DFT – 110) Multi-Unit Drum Gauge
Product Overview
b) Switch the Desired Units: Press and
release the Refresh/Select button to
switch between the units.
c) Select the Desired Units: When the
units (Liter or Gallon) desired is
flashing, press and hold the
Refresh/Select button for 7 seconds to
select the units. The units will stop
flashing and the drum size will start
flashing.
d) Switch the Desired Drum Size: Press
and release the Refresh/Select button
to switch between the drum sizes.
e) Select the Desired Drum Size: When
the drum size desired is flashing,
press and hold the Refresh/Select
button for 7 seconds to select the
drum size. The drum size will stop
flashing.
f) Return to Test Mode: Press and hold
the button until 8.8.8. is displayed – this
indicates test mode.
Testing With the DFT-110
a) After you have selected the proper
units and drum size for your
application, Press and release the
Refresh/Select button.
b) The DFT-110’s back-light is illuminated
and 8.8.8. is displayed for 4 seconds to
indicate the unit is in test mode.
c) The DFT-110 continuously monitors the
media in the vertical drum for 7
seconds and then displays this liquid
level.
d) Battery Saver Mode: 20 seconds after
the button was pressed, the back-light
is shut off. The static liquid level
reading will be displayed for 5 minutes
before the display turns off.
Note: This liquid level displayed is a static
value. You must depress the
Refresh/Select button to update the liquid
level reading.
e) A low level warning light (red LED
located on the bottom left of the LCD
display), will flash once every second
when the liquid level is <= 10% the
maximum volume.
Note: This warning light does not operate
once the unit has powered down in battery
saver mode.

SSI TECHNOLOGIES, INC.
Controls Division
2643 W. Court Street
Janesville, WI 53548-5011
Phone: [phone] Fax: [phone]
www.ssitechnologies.com
Page
4
Copyright 12/23/09
SSI Technologies Inc.
All Rights Reserved
Revision 1
RoHS
SSI Technologies - Application Note DT-AN5
Digital Fluid – TracTM (DFT – 110) Multi-Unit Drum Gauge
Product Overview
Mounting
Digital Fluid-Trac™ works well on ANSI MH2
standard 55 gallon drums as it mates with closed-
head standardized bunghole arrangements. The 55
gallon drum gauge mounts on top of the drum with
a standard 2” NPT thread connector. A ¾ inch NPS
threaded adapter is included with each Digital Fluid-
Trac™ Model DFT-110 so either bung opening can
be used on the drums.
When using the Digital Fluid-Trac™, it is important
to keep the mounting perpendicular to the liquid
level by storing the drums in an upright position.
Electrical Specifications
Resolution (Gallons) **
0.5 gallons
Resolution (Liters) **
1 Liter
Operating Temperature
0°C to 50°C
Battery Life*
6 months (Alkaline)
1 year (Lithium)
Low Level Warning
Activation (Red LED)
<= 10 % Max Volume
Low Battery Level (Lob)
<= 14.2 Volts combined
* Battery Life will vary dependant on operator’s usage.
Battery specification is based on two level readings per
day.
** Outside of stated dead band
Material Specifications
Description Material
Display housing /
threaded adaptor (blue
plastic)
PBT (Polybutylene
terephthalate), 15%
glass filled
Transducer housing
(black plastic inside
threaded adaptor)
HDPE (High Density
Polyethylene)
Distance Reading