SSV Works WP User manual

WP iPod/MP3 User Guide
Location of controls on Main Housing
Location of controls on RF Remote Control
This guide will review use of the RF Remote
Control and the functions of the your SSV Works
iPod/MP3 Overhead System
Note: To pair a new remote or re-pair your current
remote, turn the main dock power button off (#7
above), Press and hold Power and Play/Pause
button on the remote for seconds, when the
remote reads "Pair", turn the main dock power
button ON, your remote is now ready for use .
This guide will review use of the RF Remote
Control and the functions of the your SSV Works
iPod/MP3 Overhead System
In order to prolong battery life, the LCD will shut off in 5 minutes if no other button is pushed,
You will always need to press the POWER button for 2-3 second before pressing any other
command if the LCD is in "Sleep Mode"
The RF Remote has a range of approximately 20-25 feet, the LCD will display "--" if it is out of range
when a function button is pressed
Note: To pair a new remote or re-pair your current
remote, turn the main dock power button off (#7
above), Press and hold Power and Play/Pause
button on the remote for seconds, when the
remote reads "Pair", turn the main dock power
button ON, your remote is now ready for use .

Listening to an iPod
Listening to MP3 Player
Listening to FM Radio
1) Power on the unit by pressing the POWER button on the main housing (button #7)
2) Plug your iPod into the 30 pin connector
3) Secure the iPod with the Velcro straps
4) Close the water / dust protective door
5) Press and hold the POWER button on the RF Remote Control, this will turn the unit on and
show "--" on the LCD screen (shown on right)
6) Press the SOURCE button on the RF Remote to change the music mode to iPod, see button
function during iPod mode on previous page
NOTE: If using a newer iPod or iPhone with "Shake to Shuffle" you will need to go into
settings and turn this function OFF
NOTE: If you are listening to iPod mode and you change your source to Radio or Standby
mode the iPod will automatically turn OFF
iPhone NOTE: You may receive the "this accessory is not made to work with iPhone"
message just press "NO" and the device will function normally
1) Power on the unit by pressing the POWER button on the main housing (button #7)
2) Plug in your MP3 player to the 3.5mm connector at the top of the main housing
3) Secure the MP3 player with the Velcro straps
4) Close the water / dust protective door
NOTE: If using an MP3 player only the volume function on the RF Remote will work
System Notes
CORPORATE: SSV WORKS, 5330 Derry Ave, Suite N, Agoura Hills, CA, 91301
WEB: www.SSVworks.com PHONE: [phone] FAX: [phone]
1) Power on the unit by pressing the POWER button on the main housing (button #7)
2) Plug your iPod into the 30 pin connector
3) Secure the iPod with the Velcro straps
4) Close the water / dust protective door
5) Press and hold the POWER button on the RF Remote Control, this will turn the unit on and
show "--" on the LCD screen (shown on right)
6) Press the SOURCE button on the RF Remote to change the music mode to iPod, see button
function during iPod mode on previous page
NOTE: If using a newer iPod or iPhone with "Shake to Shuffle" you will need to go into
settings and turn this function OFF
NOTE: If you are listening to iPod mode and you change your source to Radio or Standby
mode the iPod will automatically turn OFF
iPhone NOTE: You may receive the "this accessory is not made to work with iPhone"
message just press "NO" and the device will function normally
1) Power on the unit by pressing the POWER button on the main housing (button #7)
2) Plug in your MP3 player to the 3.5mm connector at the top of the main housing
3) Secure the MP3 player with the Velcro straps
4) Close the water / dust protective door
NOTE: If using an MP3 player only the volume function on the RF Remote will work
This system is designed with a sleep mode on the RF Remote to give increased battery life, After 5
minutes the RF Remote will go into "Sleep Mode" thus disabling the Remote Control. To "Wake Up" the
remote press the POWER button on the remote for 2-3 seconds before attempting any other functions
on the Remote Control unit.
This system includes a dipole antenna inside the housing of the unit. For increased FM reception an
external antenna may be used. This will require removing the 10 screws on the front of the unit and
removing it from the fiberglass housing, unplug the antenna cable and plug in your new external
antenna cable after running it into the fiberglass housing
If connected directly to battery power and you are not using a toggle switch to power on/off the unit you
must be sure to always turn the main power off on the main housing when not in use, this will insure
there is no power drain on the vehicles battery system
The first time after the unit is powered on or after long periods of no use you will need to power the unit up
by pressing the POWER button inside the dock. Then, press and hold the POWER button on the remote
for 2-3 seconds or until remote turns on. You can now select source if iPod isn't displayed or press
Play/pause to play the iPod if not already playing.