Stabila LAX 50 User manual

Laser LAX 50
Operating instructions
en

1.
3.
1.
2.
1.
2.
3.
2.
1.
2.
3.
2,75 m
B1 B2 B3
C1 C2 C3
LAX-50.qxd 04.01.2007 14:59 Seite 3

A
2
3
1
4
12
6
5
13
14
15
7
8
10
11
9
LAX-50.qxd 04.01.2007 14:55 Seite 4

2m
1 mm
2m
D1
E1
D2
D3
E2 E3
LAX-50.qxd 04.01.2007 14:55 Seite 6

s> 5m
> 16
E4 F1
F2 F3
F4 F5
ft
3
2
1,5 mm
X=5m
1,5 mm
LAX-50.qxd 04.01.2007 14:56 Seite 7

(4)
The LAX-50 laser
Exit aperture for the horizontal and vertical laser lines
Rough adjustment vial
Clamp
Locking lever for clamp
Base unit
Telescopic poles
Battery compartment cover
Carrying case
en
Operating instructions
The STABILA-LAX-50 is an easy-to-use crossed line laser. It is self-levelling in the
range ± 4.5° and enables levels to be determined quickly and accurately. The verti-
cally and horizontally projected laser lines provide exact alignment / working . The
different parts of this set enable a tripod or a long support pole to be constructed to
suspend the instrument between the floor and the ceiling.
We have endeavoured to explain the unit's handling and functioning in as clear and
comprehensible manner as possible. If, however, you still have any unanswered
questions, we should be pleased to provide advice over the telephone at any time
on the following telephone number:
+49 / 63 46 / 3 09 - 0
Main components
On/off switch
Locking screws
(1)
(3)
(2)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
Securing strap
A
Securing plate
Spring
360° scale
LAX-50.qxd 04.01.2007 15:12 Seite 14

Main applications:
Unscrew the telescopic poles from the base unit.
Assemble the telescopic poles for a room height of up to
2.75 metres using the threaded sleeves.
Secure the instrument firmly between the floor and cei-
ling using the spring unit, securing plate and base unit.
Position the laser. To secure in position, turn the locking
lever until it is tight.
Opening the set.
Remove the parts.
Erect the tripod with the required height.
Position the laser.
B1
B2
B3
C1
C2
C3
Commissioning
The instrument is switched on with the on/off switch (4).
Vertical and horizontal lines will appear after switching on.
The laser will automatically level itself.
The laser will flash if the inclination is
too great.
I.
II.
III.
IV.
I.
II.
III.
IV.
Levelling at variable heights up to 2.75 metres
Levelling with tripod function
NB:
In Class II laser equipment, your eyes
are protected from accidental, short-
term exposure to the laser beam by the
lid-closing reflex and/or the reflex reac-
tion to turn one's head. This equipment
can therefore be used without additio-
nal protective measures. Nevertheless,
you should not look directly into the
laser beam. The laser goggles enclosed with these units
are not safety goggles. They are designed
to make the laser light easier to see.
Do not let the unit
fall into children's
hands!
EN 60825-1 : 03 10
LAX-50.qxd 04.01.2007 15:13 Seite 15

The LAX-50 crossed line laser is designed for use on construction sites and was per-
fectly adjusted when it left our factory. As with any precision instrument, however,
its calibration must be regularly checked. The unit should be checked before start-
ing any new tasks, particularly when the unit has been exposed to strong vibra-
tions. After an impact, the unit should be checked throughout its whole self-levell-
ling range.
Checking the calibration
You must create a reference to perform this test.
Fasten a plumbline near to the wall.
The laser unit should now be set up in front of this reference mark
(distance Y) and the vertical laser line compared with it.
The discrepancy between the centre of the laser line and the reference mark
should be no greater than 1 mm over a length of 2 m.
Vertical check
D1
D2
D3
360° scale
The vertical laser line indicates the angular displacement of the laser
unit and the laser line on the 360° scale of the base unit.
Tip:
It’s necessary to center the unit by using the
vial!
LAX-50.qxd 04.01.2007 15:13 Seite 16

Horizontal checking
1.
2.
3.
7.
4.
5.
6.
Mark the position of the visible laser line cross on the wall B (point 2).
Mark the position of the visible laser line cross on the wall A (point 1).
Switch the unit on.
Set the LAX-50 on a smooth level surface or on the tripod with the front
facing the wall.
Turn the complete unit 180° without altering the height of the laser.
Two parallel wall surfaces at least 5 m apart are required for the
horizontal check.
Without changing the height of the laser, rotate it 180° to place the beam
near the mark on the first wall (step 3 / point 1 ).
Measure the vertical distance between point 1 and
point 3. The difference must not be greater than 5 m
10 m
15 m
5,0 mm
10,0 mm
15,0 mm
Maximum permissible figure
S
Now move the unit directly in front of wall B.
Set the unit's height so that the laser dot's height matches that of
point 2.
8.
1. Horizontal checking - Line level
2. Horizontal checking - inclination of the laser line
Check the laser line for inclination and perfectly straight
projection.
E1
E2
E3
Place the instrument in front of wall A - distance X = 5 m.
Rotate the instrument through 45°.
The distance of the laser line (= point 4) from point M must not exceed 1,5 mm.
E4
F1
F2
F3
F4
F5
Calculate the centre line between point 1 and
point 3 and mark it (point M).
Rotate the instrument through 90°.
The distance of the laser line (= point 5) from point M must not exceed 1,5 mm.
Maximum tolerances at
different distances.
5 m
10 m
15 m
1,5 mm
3,0 mm
4,5 mm
Maximum permissible figure.
X
Using the horizontal laser line, align the instrument with point M.
LAX-50.qxd 04.01.2007 15:13 Seite 17

Slide the battery cover (7)
in the direction of the
arrow and insert new
batteries in accordance
with the symbols in the
battery compartment.
Replacing the
batteries
Mignon, AA , LR6
7
3 x 1,5V
alkaline mignoncells,
size AA, LR6
Suitable batteries can also be used.
Do not submerge the laser.
-> The unit is inclined too much
+ is outside the self-levelling range
+ the laser cannot level itself automatically
laser beam
ffllaasshhiinngg
Recycling programme for our EU customers:
In accordance with the WEEE regulations, STABILA provides adisposal
programme for electronic products at the end of their service life. For
more details, please contact: +49 / 6346 / 309-0
Do not store the laser when wet. Dry the
laser and case before putting the laser away.
Tip:
Remove the batteries if the unit will not be used for
a long period!
LAX-50.qxd 04.01.2007 15:13 Seite 18

• Dirty lens glass on the beam emitter detracts from the quality of the beam.
It should be cleaned with a soft cloth.
• Clean the laser unit with a damp cloth. Do not spray or immerse the unit!
Do not use solvents or thinners!
Subject to technical modifications.
Care and maintenance
Like any precision instrument, handle the LAX-50 crossed line laser carefully and
cautiously.
Laser type:
Technical data
Self-levelling range:
Output:
Levelling accuracy:
Batteries:
Operating life:
Operating temperature range:
Storage temperature range:
Red diode laser, wavelength 635 nm
< 1 mW, Laser Class 2
to EN 60825-1:03-10
ca. ± 4,5°
± 0,5 mm/m
3 x 1,5 V mignoncells alkaline, size AA, LR6
approx. 30 hours (alkaline)
-10 °C to +50 °C
-20 °C to +60 °C
LAX-50.qxd 04.01.2007 15:13 Seite 19