Stabila TECH 700 DA User manual

TECH 700 DA
How true pro’s measure
www.stabila.com
User manual

en
2
Contents
Section Page
• 1. Intended use 3
• 2. Components of the unit 3
• 3. Insert batteries/Battery replacement 4
• 4. Commissioning 4
• 5. Automatic switch-off time 4
• 6. Angle finder 5
• 7. Spirit level 5
• 8. Bevel gauge 5
• 9. Reference function 6
• 10. Lighting 7
• 11. HOLD function 7
• 12. Angle halving 8
• 13. Calibration of zero position 8
• 14. Technical Data 9

en
3
On/Off
Reference function
HOLD function
Angle halving
Lighting
The STABILA TECH 700 DA is an electronic angle
finder with digital display for quickly and easily
measuring angles.
Together with the vials, the angle finder can also
be used as a spirit level.
If you still have questions aer reading
through the operating instructions, you
can obtain advice by telephone:
[phone]
1.800.869.7460 U.S. and Canada
Equipment and functions:
• Electronics module with digital display for
accurately setting and measuring angles
• Vertical vial for vertical levelling
• Horizontal vial for horizontal levelling
1. 2 measuring surfaces
2. Vials - vertical and horizontal
3. Arm with 2 marking and cutting edges
4. LOCK system - to x the set angle
5. Keyboard
6. Display
7. Battery compartment lid
1. Intended use
2. Components of the unit

en
4
Unscrew battery compartment lid on front,
insert new batteries according to symbol in
battery compartment.
Suitable rechargeable batteries can also be used.
LCD:
low battery charge - insert new battery
Dispose of used batteries at suitable
collection points - not with household
waste. Do not leave in unit!
Remove the batteries if you do not
intend to use the unit for some time!
After switching on, the version number S x.xx of
the measuring program is briefly displayed.
The unit is switched off by briefly pressing
the "ON/OFF" button. The "OFF" confirmation
appears for 1 second.
If not used for long periods, the electronic angle
finder automatically switches off after 2 hours.
2.
1.
2x 1.5V alkaline
AA, LR6, Mignon
MN 1500
2h
2
1Auto OFF
1x
1x
1 sec
3. Insert batteries / Battery replacement
5. Automatic switch-o time
4. Commissioning

en
5
0,5 mm/m
0,75mm/m 0,75mm/m
0,029°
0,043°
0°... 270°
The angle finder displays the angle currently set
between the arm and body. Angle measurements
can be taken between 0° and 270°.
The angle finder with 2 measuring surfaces is
also a fully functional spirit level for horizontal
and vertical measurements to level construction
elements. High-quality STABILA technology
makes the vials suitable for measurements:
(1) in the normal position
(2) in the reverse position
The LOCK system can be used to fix the arm at
the set angle.
8. Bevel gauge
7. Spirit level
6. Angle nder

en
6
The REF button can be used to select any set
angle as 0° reference. The angle details now
displayed relate to this reference angle.
The next time the arm is rotated, only the newly
set angle is displayed. The display flashes in this
setting. The REF symbol indicates this function
setting.
The original reference angle value is displayed
for 2 seconds by briefly pressing the REF button.
The reference angle is deleted by:
• pressing and holding (≥ 3 sec) the REF button
• switching off
• the automatic switch-off function
Positive and negative angles when adjusting
the arm:
angle greater than reference: positive
angle less than reference: negative
Only the negative sign is displayed
1x
2 sec
3 sec
1x
1x
9. Reference function

en
7
1x
1x
1x
The current measurement can be saved by
pressing the HOLD button. The measurement is
displayed continuously. In this setting, the display
flashes and the HOLD symbol is displayed.
This function can be used in combination with
the reference function.
The saved measurement is deleted by again
pressing the HOLD button or switching the unit off.
1x
Repeatedly pressing the "Lighting" button
switches the display lighting on, to half
luminance or off.
11. HOLD function
10. Lighting

en
8
The current measurement is halved by pressing
the "Angle halving" button. The measurement is
displayed continuously. In this setting, the display
flashes and the "Angle halving" symbol is
displayed.
The value is deleted by again pressing the
"Angle halving" button or switching the unit off.
During use, instances may arise when the display
does not show 0.0° when the arm is swivelled all
the way in.
If this happens, rst check whether dirt is prevent-
ing the arm from closing fully. If the display is still
not showing 0.0°, the unit must be calibrated.
With the arm folded all the way in, the zero position
is calibrated by pressing and holding the ON/OFF
button. "CAL" is displayed for approx. 1 second.
Successful calibration is confirmed with "rdy".
The unit cannot be recalibrated if "Error" appears
on the display. The angle nder must be returned
for inspection.
3 sec
1x
Display value ≠ 0.0°
1x
13. Calibration of zero position
12. Angle halving

en
9
Accuracy of electronics module:
Angle measurement: ± 0.1°
Accuracy of spirit level:
in normal position: 0.5 mm / m = 0.029°
in reverse position: 0.75 mm / m = 0.043°
Measuring range: 0° - 270°
Batteries : 2 x 1.5 V alkaline, size Mignon, AA, LR6
Operating life : ≥ 150 hours
Operating temperature range: -10 °C to +50 °C / 14°F to 122°F
Storage temperature range: -20 °C to +65 °C / -4°F to 149°F
Protection class: IP 54
Subject to technical modifications.
14. Technical Data

www.stabila.com
USA
Canada
Europe
Middle and South America
Australia
Asia
Africa
STABILA Inc.
332 Industrial Drive
South Elgin , IL 60177
800-869-7460
[email protected]
STABILA Messgeräte
Gustav Ullrich GmbH
P.O. Box 13 40 / D-76851 Annweiler
Landauer Str. 45 / D-76855 Annweiler
+ 49 63 46 309 - 0
[email protected]