Stage Light PIXBAR HEX 6 User manual

V1.0
Caution: For safety, please read this user manual carefully before initially use!
Safety Instructions:
• Do not open this device, there is no user-serviceable parts inside.
• DO not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot when lights are operating.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety rope when mounting this device overhead.
• Do not operate this device outdoors or where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
In case of a serious operating problem, stop using immediately.
The maximum ambient temperature is 104°F (40°C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz
Link up to the maximum 16 devices at 120 VAC or 30 at 230 VAC. DO NOT exceed this quantity.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
USER MANUAL
Pixel Bar
Model No. PIXBAR HEX 6
1/8 V1.0

CONTROL BOARD OPERATION
Display Function
1.DMX Address
2.DMX Channel
3.Dimmer Curve
4. Static Color
5.Manual Color
6.Manual WT
7.Auto Program
8.Sound Mode
9.Master/Slave
10.Factory Set
Use Up and Down button to select your desired operation, then press Enter to confirm.
press "Enter" again to confirm.
CH06, CH08, CH12, CH36, CH38 press "Enter" again to confirm.
then press Entre to confirm your selection.
Mode:
Value: Function:
Static color <R> Red
Static color <G> Green
Static color <B> Blue
Static color <W> White
Static color <A> Amber
Static color <U> UV
Static color <GB> Green+Blue
Static color <RG> Red+Green
Static color <RB> Red+Blue
Static color <RW> Red+White
Static color <GW> Green+White
Static color <BW> Blue+White
Static color <WA> White+Amber
Static color <RA> Red+Amber
Static color <GA> Green+Amber
Static color <BA> Blue+Amber
Static color <RGB> Red+Green+Blue
Static color <RGW> Red+Green+White
Static color <GBW> Green+Blue+White
Static color <GBA> Green+Blue+Amber
Static color <BWA> Blue+White+Amber
Static color <RGA> Red+Green+Amber
Static color <GWA> Green+White+Amber
Static color <RWA> Red+White+Amber
Static color <RGBA> Red+Green+Blue+Amber
Static color <GBWA> Green+Blue+White+Amber
Static color <RGBW> Red+Green+Blue+White
Static color <RBWA> Red+Blue+White+Amber
Select "3.Dimmer Curve" , press ENTER, there are 4 dimming modes for option, select the desired dimming code ,
Entered "4. Static Color" mode, you can select the desired solid color via the UP or DOWN buttons and confirm by Enter
Setting Static Colors
Static Color
DMX Addressing:
After select the "DMX Address" and press Enter, then use Up and Down to set the desired DMX address (001~512),
DMX Modes (Eight DMX modes option)
After select the "2.DMX Channel" and press Enter, then use Up and Down to set the desired DMX mode CH03,CH04,
Dimming Mode:
Press the Menu until one of the following displayed:
To set DMX channel modes: CH03,CH04, CH06, CH08, CH12, CH36, CH38
To set static colors: Static Color R, G, B, W, A,U,GB, RG,RB, RW, GW, BW,WA,RA,GA,BA……
To set user mode intensity of R, G, B ,W,A,UV separately for color mixing and strobe rate (S000-S100).
To set user mode intensity of 11 white color temperature separately .
To set built-in automatic programs: Pr 01 ~ Pr 19 and speeds <Speed 000 ~ Speed100>
To set DMX address
To set dimmer speeds: <01> , <02>, <03>, <04>
To set sound active mode and the sensitivity (S000 ~ S100)
To set Master/Slave modes
To recover the factory default setting
2/8 V1.0

Static color <RGWA> Red+Green+White+Amber
Static color <RGBWA> Red+Green+Blue+White+Amber
Static color <RU> Red + Green
Static color <GU> Red + Green + Blue
Static color <AU> Red + White
Static color <RAU> Green + White
Static color <RGBWAU> Red + Green + Blue + White
This mode allows the user set intensity of R, G, B, W ,A,UV separately to get endless color mixing from the control
board without DMX controller to set the device to run strobe desired.
Entered "5.Manual Color" mode, use <UP> and <DOWN> to select the " R/G/B/W/A/U " for Colors intensity or "S"
for strobe speed.
Use <UP> and <DOWN> to set the colors intensity values " 0 ~ 255" or Strobe speed values "000 ~ 100"
Manual Color temperature
W01 Color Temperature 1 WARM
W02 Color Temperature 2
W03 Color Temperature 3
W04 Color Temperature 4
W05 Color Temperature 5
W06 Color Temperature 6
W07 Color Temperature 7
W08 Color Temperature 8
W09 Color Tempreature 9
W10 Color Tempreature 10 COOL
W11 Color Tempreature 11
Entered "7.Auto Program" mode, use <UP> and <DOWN> to select the built-in programs "Pr 01 ~ Pr 19" then press
the "Enter" to confirm "Enter" to confirm.
Use <UP> and <DOWN> to select the operating speed of the program(Value:S 000 ~ S100, Freeze,Slow ~ Fast),
press "Enter" to confirm.
Mode:
Value: Function:
PR 01 R G B W A UV colors switching
PR 02 36 colors switching
PR 03 R G B W A UV colors fading(slow in slow out)
PR 04 36 colors Fading(slow in slow out)
PR 05 R G B W A UV colors fading(slow in fast out)
PR 06 36 colors Fading(slow in fast out)
PR 07 R G B W A UV colors fading(fast in slow out)
PR 08 36 colors Fading(fast in slow out)
PR 09 Color Macros
PR 10 Auto Chasing 1
PR 11 Auto Chasing 2
PR 12 Auto Chasing 3
PR 13 Auto Chasing 4
PR 14 Auto Chasing 5
PR 15 Auto Chasing 6
PR 16 Auto Chasing 7
PR 17 Auto Chasing 8
PR 18 Auto Chasing 9
PR 19 Multi chasings
(Freeze, Slow ~ Fast), then press "Enter" to confirm.
Enter "Manual WCT" mode,select various color temperature with <WT01>~<WT11>,
use <UP> and <DOWN> to select intensity for every single color temperatue with <Dim:001>~<Dim:100>
Automatic Mode
This fixture has a built-in automatic program.
Static Color
Manual Color Mode
Auto Program
3/8 V1.0

Special Chaser Mode (only available for the internal programs Pr 19)
This mode enables several slave units after the other so that chaser effects can be operated over several devices.
You can build up to 255 different slave groups.
as an explanation, we give an example with 10 different slave groups.
Settings for the master device
1. Set the DMX address to 010 (number of slave groups), press Enter to confirm.
2. Set Auto Program to Pr 19, press ENTER to confirm.
Setting for the slave devices
1. Set the slaves devices to Slave mode, press Enter, "Slave MODE" displayed
2. Set the slave devices DMX address to the desired slave group (here 001 - 010) via the UP or DOWN buttons.
Press ENTER to confirm.
See below chart:
Master/Slave Operation
1) Set the master fixture to one of the standalone operating modes: automatic, sound, static color or manual
color modes
2) The fixture is set Slave in default,if you want to set it Master,entered "09.Master/Slave" mode,
set to <M>, press Enter. "Master " will display.
Factory Set
Select Factory Set , Enter,Select YES , recovering the factory default setting .
Sound Mode
Entered "8.Sound mode", use <UP> and <DOWN> to set the sensitivity Sen 000 ~ Sen 100, press Enter to confirm.
4/8 V1.0

DMX VALUES:
3 Channels Mode:
CHANNEL VALUE FUNCTION
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 Channels Mode:
CHANNEL VALUE FUNCTION
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
6 Channels Mode:
CHANNEL VALUE FUNCTION
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
5 000-255 Amber: 0% ~ 100%
6 000-255 UV 0%~100%
8 Channels Mode:
CHANNEL VALUE FUNCTION
1 000-255 Red 0% ~ 100%
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%
5 000-255 Amber 0%~100%
6 000-255 UV 0%~100%
7 000-255 Master DIMMER 0% ~ 100%
000-009 No function
010-255 Strobe : Slow ~ Fast (1~30Hz)
12 Channels Mode:
CHANNEL VALUE FUNCTION
1 000-255 Red 0% ~ 100%
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%
5 000-255 Amber 0%~100%
6 000-255 UV 0%~100%
7 000-255 Master DIMMER 0% ~ 100%
000-009 Strobe OFF
010-255 Strobe (slow-fast 1-30Hz)
000-009 No Function
010-031 Color Temprature 1 WARM
032-054 Color Temprature 2
055-077 Color Temprature 3
078-100 Color Temprature 4
101-123 Color Temprature 5
124-146 Color Temprature 6
147-169 Color Temprature 7
170-192 Color Temprature 8
193-215 Color Temprature 9
216-238 Color Temprature 10 COOL
239-255 Color Temprature 11
9
8
8
5/8 V1.0

000-009 No Function
010-021 R G B W A UV colors switching
022-034 36 colors switching
035-047 R G B W A UV colors fading(slow in slow out)
048-060 36 colors Fading(slow in slow out)
061-073 R G B W A UV colors fading(slow in fast out)
074-086 36 colors Fading(slow in fast out)
087-099 R G B W A UV colors fading(fast in slow out)
100-112 36 colors Fading(fast in slow out)
113-125 Color Macros
126-138 Auto Chasing 1 (Auto Pr10)
139-151 Auto Chasing 2 (Auto Pr11)
152-164 Auto Chasing 3 (Auto Pr12)
165-177 Auto Chasing 4 (Auto Pr13)
178-190 Auto Chasing 5 (Auto Pr14)
191-203 Auto Chasing 6 (Auto Pr15)
204-216 Auto Chasing 7 (Auto Pr16)
217-229 Auto Chasing 8 (Auto Pr17)
230-242 Auto Chasing 9(Loop PR10 ~ PR 17)
243-255 Sound Active
11 000-255 Speed of Auto Programs (Slow ~ Fast)
000-009 Use the dimmer of control board setting
10-70 Curved dimming 1
71-132 Curved dimming 2
133-194 Curved dimming 3
195-255 Curved dimming 4
36 Channels Mode:
CHANNEL VALUE FUNCTION LED
1 000-255 Red 0% ~ 100%
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%
5 000-255 Amber 0%~100%
6 000-255 UV 0%~100%
7 000-255 Red 0% ~ 100%
8 000-255 Green 0% ~ 100%
9 000-255 Blue 0% ~ 100%
10 000-255 White 0% ~ 100%
11 000-255 Amber 0%~100%
12 000-255 UV 0%~100%
13 000-255 Red 0% ~ 100%
14 000-255 Green 0% ~ 100%
15 000-255 Blue 0% ~ 100%
16 000-255 White 0% ~ 100%
17 000-255 Amber 0%~100%
18 000-255 UV 0%~100%
19 000-255 Red 0% ~ 100%
20 000-255 Green 0% ~ 100%
21 000-255 Blue 0% ~ 100%
22 000-255 White 0% ~ 100%
23 000-255 Amber 0%~100%
24 000-255 UV 0%~100%
25 000-255 Red 0% ~ 100%
26 000-255 Green 0% ~ 100%
27 000-255 Blue 0% ~ 100%
28 000-255 White 0% ~ 100%
29 000-255 Amber 0%~100%
30 000-255 UV 0%~100%
12
5
1
2
3
4
10
6/8 V1.0

31 000-255 Red 0% ~ 100%
32 000-255 Green 0% ~ 100%
33 000-255 Blue 0% ~ 100%
34 000-255 White 0% ~ 100%
35 000-255 Amber 0%~100%
36 000-255 UV 0%~100%
38 Channels Mode:
CHANNEL VALUE FUNCTION LED
1 000-255 Red 0% ~ 100%
2 000-255 Green 0% ~ 100%
3 000-255 Blue 0% ~ 100%
4 000-255 White 0% ~ 100%
5 000-255 Amber 0%~100%
6 000-255 UV 0%~100%
7 000-255 Red 0% ~ 100%
8 000-255 Green 0% ~ 100%
9 000-255 Blue 0% ~ 100%
10 000-255 White 0% ~ 100%
11 000-255 Amber 0%~100%
12 000-255 UV 0%~100%
13 000-255 Red 0% ~ 100%
14 000-255 Green 0% ~ 100%
15 000-255 Blue 0% ~ 100%
16 000-255 White 0% ~ 100%
17 000-255 Amber 0%~100%
18 000-255 UV 0%~100%
19 000-255 Red 0% ~ 100%
20 000-255 Green 0% ~ 100%
21 000-255 Blue 0% ~ 100%
22 000-255 White 0% ~ 100%
23 000-255 Amber 0%~100%
24 000-255 UV 0%~100%
25 000-255 Red 0% ~ 100%
26 000-255 Green 0% ~ 100%
27 000-255 Blue 0% ~ 100%
28 000-255 White 0% ~ 100%
29 000-255 Amber 0%~100%
30 000-255 UV 0%~100%
31 000-255 Red 0% ~ 100%
32 000-255 Green 0% ~ 100%
33 000-255 Blue 0% ~ 100%
34 000-255 White 0% ~ 100%
35 000-255 Amber 0%~100%
36 000-255 UV 0%~100%
37 000-255 Master DIMMER 0% ~ 100%
000-009 No function
010-255 Strobe : Slow ~ Fast (1~30Hz)
6
38
1
2
3
4
5
6
7/8 V1.0

TECHNICAL SPECIFICATIONS
PIXBAR HEX 6
Power supply: 100~240 V AC, 50/60 Hz ~
Power consumption:60 W
DMX control channels: 3 / 4 / 6 / 8 / 12 / 36 / 38 chs
DMX512 connection: 3-pin XLR
Sound-control: via built-in microphone
LED type: 12W RGBWA+UV 6in1
Number of LEDs: 12
Beam angle: 15°/ 25°/30°
Dimensions (LxWxH): 568x 80 x 165 mm
Weight:2.6 kg
Maximum ambient temperature Ta: 40°C
Maximum housing temperature TC (steady state): 80°C
Min. distance from flammable surfaces: 0.5 m
Min. distance to lighted object: 0.1 m
Fuse: T 1 A, 250 V
8/8 V1.0