Stagg KINGPAR 5 User manual

!
User Manual
KINGPAR 5
SLI-KINGPAR5

!

!
Before Usage
This package contains
- 1x Kingpar 5
- 1x Power Cable
- 1x User Manual
Unpacking: Thank you for purchasing this product, it has been thoroughly
tested and has been shipped in perfect operating condition. Carefully check the
packaging for damage that may have occurred during shipping. If the packaging
appears to be damaged, carefully inspect your fixture for any damage and be
sure all equipment necessary to operate the unit has arrived intact. If damage
has been found or parts are missing, please contact your vendor or our customer
support number for further instructions.
Introduction: The fixture can operate in three different operating modes: DMX
control, sound active, or in a Master/Slave configuration. This product comes
with several built-in programs that can be used while operating as a single unit
or with multiple units linked in a master/slave configuration. For best results use
fog or special effects smoke to enhance the beam projection.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose
this unit to rain or moisture.
Warning! This product may cause severe eye damage. Avoid looking directly
into the light source at all times!

!
Specifications:
•Voltage: AC100V~240V, 50~60HZ
•Power Consumption: 73W
•LED Quantity: 6x Cool white, 12x Warm white
•Beam Angle: 25°
•IP Grade: IP20
•DMX channels: 5
•Packaging Size: 300*300*380 mm
•Net weight: 3,1Kg
•Gross weight: 4,53Kg
Features
•3PIN plug DMX in and out
•IEC power plug in and out
•Die-cast aluminium housing
•LED display for easy setup
•Working indoor temperature -20°C~+40°C
•Strobe/Colour temperature selection

!
Installation
1. The product can be hung or placed on a solid surface with the double
mounting brackets
2. If you install the light in a hanging position, always use a suitable mounting
position and a clamp or screw that is strong enough to hold the product
without stress. Always use a safety wire to secure the light.
3. Always keep a distance of minimum 0.5m to all objects or persons
4. Installation should always be done by a trained professional.
5. Make sure the light always has good ventilation
Power Connection
Please make sure the rated voltage and frequency comply with your local
voltage.
Brown
Positive
3
Blue
Negative
2
Green/Yellow
Ground
1

!
DMX 512 Connection
The DMX512 signal of the controller is connected to the Input and
(1 Earth, 2 Negative, 3 Positive). The length of the signal cable should never
exceed 100 meters in order to avoid the interference. Please refer to the details
in following pictures.
Operation
Control panel Function
Button
Function
MENU
Choose mode or exit menu
ENTER
Select menu or confirm setting
UP
Scroll up in menu
DOWN
Scroll down in menu

!
Menu Map

!
Operating Instructions
[DMX address set up]
•Press MENU then Up or DOWN until "Addr" is displayed, then press ENTER
•By UP and DOWN to change the DMX address Press ENTER to confirm the
DMX address
[STATIC COLOURSET UP]
•Press MENU, and then press UP or DOWN, until "STAT" is displayed,then
press ENTER
•Use UP or DOWN to choose between ST00(strobe), a000(warm white), C000
(cool white).

!
You can adjust each setting individually by selecting the setting with ENTER,
and using UP or DOWN to change the value. Push ENTER to confirm, push
MENU to go back to the main menu and use UP and DOWN to choose a
different setting.
[Color temperature selection]
•Press MENU, then press UP or DOWN until Colo is displayed,then press
ENTER
•Using UP or DOWN you choose between 2800K, 3200K, 3500K, 4200K,
4900K, 5600K, 5900K, 6500K. These preset color temperatures allow you to
easily choose the correct cold or warm white light for your application

!
[slave mode]
•Press MENU, then press UP or DOWN until SLAv is displayed, then press
ENTER. The display will show "Sla" and follow the master's settings.
[software version]
•Press MENU, then press UP or DOWN until vEris displayed, then press
ENTER. The current software version will be displayed.
DMX Channels & Value
Channel
Value
Function
ch1
0--255
dimmer (0%--100%)
ch2
0--255
Warm white (0%--100%)
ch3
0--255
Cool white (0%--100%)
ch4
0--255
Strobe 0-20HZ
(slow -- fast)
Ch5
0--15
16--44
45--74
75-104
105-134
135-164
165-194
195-224
225-255
None
2800K
3200K
3500K
4200K
4900K
5600K
5900K
6500K

!

!
!
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS.
• If, after you have followed the instructions outlined above, this device fails to function, please
contact your dealer. Under no circumstances should this device be opened. Leave all servicing to
qualified personnel.
•Electrical appliances must never be used in conditions of high humidity or heat. To prevent any risk
of fire or electric shock, never spill or splash liquids on this device. Should this happen, unplug the
power cable from the mains outlet and switch off the mixer immediately.
MARKING & CONFORMITY
1. The CE mark on this product means it conforms to the EMC Directive (2004/108/CE), CE marking
Directive (93/68/EEC) and Low Voltage Directive (2006/95/EC).
2. The «Crossed-out Wheeled Bin» is to draw your attention to the WEEE (Waste Electric &
Electronic Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately
for recycling.
3. «RoHS compliant» means this device conforms to the Directive (2002/95EC) on the restriction of
the use of certain hazardous substances in electrical and electronic equipments, such as: Mercury,
Lead, Cadmium, Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated
Diphenyl Ethers (PBDE).
24-10-2012