Stairville DJ Lase 40-G MKII User manual

DJ Lase 40-G MKII / 100-R MKII / 150-B
Owner‘sManual
DJ lase
DJ lase 40-G MKII / 100-r MKII / 150-B

DJ Lase 40-G MKII / 100-R MKII / 150-B
2
Contents
General notes on safety ......................................................................................................................3
Power supply .............................................................................................................................3
Operating conditions ..................................................................................................................3
Laser safety ........................................................................................................................................4
Intended use ..............................................................................................................................4
Installation ...........................................................................................................................................5
General installation rules ...........................................................................................................5
DMX connectors ........................................................................................................................5
Setup ...................................................................................................................................................6
Connections in DMX mode ........................................................................................................6
Connections in master/slave mode ............................................................................................6
Components and functions .................................................................................................................7
Front side ...................................................................................................................................7
Rear side ...................................................................................................................................8
Operation ............................................................................................................................................9
Start the device ..........................................................................................................................9
Main menu .................................................................................................................................9
Auto show mode ........................................................................................................................9
Music mode ...............................................................................................................................9
Sound sensitivity ........................................................................................................................9
DMX mode .................................................................................................................................9
Master/slave mode .....................................................................................................................9
Stop the device ..........................................................................................................................9
Menu diagram ..........................................................................................................................10
Functions in DMX mode .......................................................................................................... 11
Pattern list ................................................................................................................................12
Troubleshooting ................................................................................................................................13
The device does not work, no light and the fan does not work ................................................13
No response to the DMX controller ..........................................................................................13
Cleaning ............................................................................................................................................13
Technical data ...................................................................................................................................14
Protecting the environment ...............................................................................................................15
Disposal of the packaging material ..........................................................................................15
Disposal of your old device ......................................................................................................15

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
3
General notes on safety
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in elec-
tric shock, re or serious injury.
Save all warnings and instructions for future reference.
DANGER
Electric shock caused by high voltages inside!
Within the unit there are areas where high voltages may be present. To reduce the risk of
electric shock do not remove any covers unless the AC mains power cord is removed.
Covers should be removed by qualied service personnel only.
There are no user-serviceable parts inside.
DANGER
Electric shock caused by short circuit!
Always use proper ready-made insulated mains cabling (power cord) with a protective con-
tact plug. Do not modify the mains cable or the plug. Failure to do so could result in electric
shock/death or re. If in doubt, seek advice from a registered electrician.
Power supply
Notice
Malfunction or damage to equipment!
Ensure that the input voltage (AC outlet) matches the voltage rating of the product. Failure to do so could
result in damage to the product and possibly the user.
Unplug the unit before electrical storms occur and when unused for long periods of time.
Operating conditions
Always install and use the device in accordance with these instructions.
Notice
Malfunction or damage to equipment!
This device has been designed for indoor use only. Do not expose the device to any liquid or moisture. Do not
install the unit near any direct heat source. Keep the unit away from naked ames.
Do not block areas of ventilation. Failure to do so could result in re.
This device has not been designed for continuous use. Regular breaks during operation are essential to maxi-
mize the lifetime.
Do not switch the device on and off in short time intervals.

DJ Lase 40-G MKII / 100-R MKII / 150-B
4
Laser safety
This information is based on DIN EN 60825-1.
This device is a class 3B laser product. It is equipped with a safety key. Always remove the key when the de-
vice is not operated by trained personnel.
As an operator you are responsible for the safety of all persons present.
Familiarize yourself with the laser safety regulations that apply in your country. To ensure safe operation, it is
important to pay attention to the following instructions.
DANGER
Laser radiation – avoid exposure to beam!
This device is a class-3B laser product, classied according to EN 60825-1. Do not look into
the laser beam. The laser beam can injure your eyes when you directly look into it.
Do not expose to the laser beam. The laser beam can cause skin burns.
In this context take extreme care when using converging optical instruments.
WARNING
Risk of epileptic shock!
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons must avoid
looking at strobe lights.
Notice
Laser radiation – re hazard!
Keep the laser area free of ammable objects.
Intended use
This device has been designed for show applications only. Any compensation claims caused by inappropriate
or unintended use are always excluded.

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
5
Installation
DANGER
Laser radiation!
During installation follow the instructions specied in section “Laser safety” on page 4.
DANGER
When using additional components!
Additional components can cause dangerous laser beam diffusion when they are not
properly connected.
Notice
Safety switch required!
We strongly recommend to install a remote manual safety switch to the device. The safety switch turns the
laser off immediately.
General installation rules
You can install the device on the wall, the ceiling or on the ground. A mounting bracket is provided together
with the device.
WARNING
Injuries caused by falling parts!
Make sure that the installation complies with the standards and rules that apply in your
country.
Always secure the device with a secondary safety attachment, such as a safety cable or a
safety chain.
Notice
Malfunction or damage to equipment!
The distance between light output and the illuminated surface must be more than 0.5 m (19.7 in).
Ensure also that there is enough room for ventilation.
The ambient temperature must always be between 10 °C (50 °F) and 45 °C (113 °F).
DMX connectors
A female 3-pin XLR connector is used for the DMX output, a male 3-pin XLR connector for the DMX input. The
gure below and the following table show the pin assignment.
3
1
2
1 Ground
2 DMX data (–)
3 DMX data (+)

DJ Lase 40-G MKII / 100-R MKII / 150-B
6
Setup
DANGER
Laser radiation!
During setup follow the instructions specied in section “Laser safety” on page 4.
The required connections depend on the operation mode of the device.
Notice
Malfunction or damage to equipment!
For failure-free operation of the DMX chain, use dedicated DMX cables. Never use ordinary microphone
cables.
Never connect the DMX output to audio devices such as mixers or ampliers. The voltages used on the DMX
lines may severely damage the audio input circuits.
Connections in DMX mode
Connect the DMX input of the device to the DMX output socket of a DMX controller or another DMX device.
Connect the output of the rst DMX device to the input of the second one, and so on to form a daisy chain.
Always ensure that the output of the last DMX device in the daisy chain is terminated with a 120-Ω resistor.
When the device is congured for DMX mode, but no DMX signal is being received, the display ashes.
Connections in master/slave mode
When you congure a group of devices in master/slave mode, the rst unit will control the other units for an au-
tomatic, sound-activated, synchronized light show. This function is ideal when you want to start a show imme-
diately. Connect the DMX output of the master device to the DMX input of the rst slave device. Then connect
the DMX output of the rst slave device to the DMX input of the second slave device and so on.

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
7
Components and functions
Front side
POWER MUSIC
ö# $
DJ Lase
100-R MKII
LASER RADIATION
AVOID EXPOSURE TO BEAM
LASER CLASS 3B
öPOWER: Shows that the device is turned on
#MUSIC: Shows that a sound or music signal is being detected
$Laser aperture

DJ Lase 40-G MKII / 100-R MKII / 150-B
8
Rear side
OUTPUT INPUT
DMX-512POWER
MAINS: 100-240Vac50/60Hz
FUSE: 1A/250Vac slow
USE ONLY WITH A 250 V FUSE
OFF
ON
LOCK
SAFETY EYE
ATTACH SAFETY
CABLE HERE
RISK OF ELECTRIC SHOCK
DISCONNECT INPUT POWER
BEFORE OPENING
WARNING: THIS APPLIANCE MUST BE EARTHED
LASER
0.5m
888 MIC
FUNC UP DOWN ENTER
CONTROL
SERIAL N°.
%&
1
') +, -. /
*
(
0
%Main switch
&Fuse holder
'Plug for mains cable; the input voltage is printed next to it
(INPUT: DMX input
)Safety key switch: Turns the laser output on or off
*Safety eye
+FUNC: Opens the main menu
,UP: Increases the displayed value by one
-DOWN: Decreases the displayed value by one
.ENTER: Chooses between the options of the selected mode
/MIC: Microphone used for the sound mode
0Display
1OUTPUT: DMX output

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
9
Operation
Start the device
Perform the following steps to start the operation:
1. Verify that all required laser safety precautions have been taken. Make sure that there is no one in the
reach of the laser beam.
2. Insert the safety key (8) and turn it to the “OFF” position.
3. If not already connected, connect the device to the mains (6).
4. Using the main switch (4) turn the device on. After a few seconds, the fan and the motors start to work.
The display shows the current operation mode. The device is now operational.
5. Turn the safety key (8) to the “ON” position to turn the laser beam on.
Main menu
Press “FUNC” to activate the main menu and to select one of the operation modes.
When the display ashes, use the “UP” and “DOWN” buttons to change the displayed value. When the display
shows the desired value, press “ENTER”. To go back to the main menu without any changes, press “FUNC” or
wait for one minute.
All settings that were made previously are kept, even if you disconnect the device from the power supply.
Auto show mode
Aut Press “FUNC” until the display shows “Aut”. The device operates in stand-alone mode and displays a
pre-programmed show. Press “ENTER” to conrm and to start the operation.
Music mode
SoU Press “FUNC” until the display shows “SoU”. The device operates in stand-alone mode, the built-in
microphone controls a pre-programmed show. Press “ENTER” to conrm and to start the operation.
Sound sensitivity
S 6 Press “FUNC” until the display shows “S 6” and starts ashing. This menu is used to set the sensitiv-
ity of the microphone. Using the “UP” and “DOWN” buttons, you can now choose between “S 0”
(sensitivity = 0, music mode disabled) and “S 1” (low sensitivity) to “S 9” (high sensitivity). Press “ENTER” to
store the setting.
DMX mode
001 Press “FUNC” until the display shows “001”. You can now set the number of the rst DMX channel of
the device (DMX address). Select a value between 1 and 512 using the “Up” and “Down” buttons.
Press “ENTER” to store the value and to start the operation in DMX mode.
Ensure that this channel number ts to the conguration of your DMX controller. Since the device uses eight
DMX channels, the highest usable DMX start address is 505.
Master/slave mode
SLA Press “FUNC” until the display shows “SLA”. In this mode, the device exactly follows the operation of
the “master” it is connected to. Press “ENTER” to conrm and to start the operation.
Stop the device
Perform the following steps to stop the operation:
1. Turn the safety key (8) to the “OFF” position to turn the laser beam off and remove the key. Keep the safety
key under control.
2. Using the main switch (4) turn the device off.
3. Optionally, disconnect the device from the mains (6).

DJ Lase 40-G MKII / 100-R MKII / 150-B
10
Menu diagram
Aut
SoU
S 6 S 0
S 9
001
512
SLA
001
DMX mode
Auto show mode
Music mode
Sound sensitivity
Master/slave mode

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
11
Functions in DMX mode
Channel Value Function
1 Mode selection
0…63 Laser off
64…127 Auto show; the device operates in stand-alone mode and display a pre-programmed show
128…191 Music mode; the built-in microphone controls a pre-programmed show
192…255 DMX mode; this setting enables the function of the other DMX channels
2 0…255 Pattern selection (as shown in the pattern list)
3 Zoom
0…127 Fixed zoom (100 % to 5 %)
128…169 Zoom-in effect, speed increasing
170…209 Zoom-out effect, speed increasing
210…255 Zoom-in and zoom-out effect, speed increasing
4 Y axis rotation
0…127 0° to 359° xed Y axis position
128…191 Clockwise rolling effect, speed increasing
192…255 Anti-clockwise rolling effect, speed increasing
5 X axis rotation
0…127 0° to 359° xed X axis position
128…191 Clockwise rolling effect, speed increasing
192…255 Anti-clockwise rolling effect, speed increasing
6 Z axis rotation
0…127 0° to 359° xed Z axis position
128…191 Clockwise rolling effect, speed increasing
192…255 Anti-clockwise rolling effect, speed increasing
7 X axis moving
0…127 128 different xed positions on X axis
128…191 Clockwise moving effect, speed increasing
192…255 Anti-clockwise moving effect, speed increasing
8 Y axis moving
0…127 128 different xed positions on Y axis
128…191 Clockwise moving effect, speed increasing
192…255 Anti-clockwise moving effect, speed increasing

DJ Lase 40-G MKII / 100-R MKII / 150-B
12
Pattern list
0…7 64…71 128…135 190…197
8…15 72…79 136…143 198…205
16…23 80…87 144…151 206…213
24…31 88…95 152…159 214…221
32…39 96…103 160…167 222…229
40…47 104…111 168…175 230…237
48…55 132…119 176…181 238…245
56…63 140…127 182…189 246…255

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
13
Troubleshooting
DANGER
Laser radiation!
During troubleshooting follow the instructions specied in section “Laser safety” on
page 4.
DANGER
Laser radiation inside!
Only qualied personnel may carry out service activities when the covers of the device are
open.
DANGER
Laser radiation!
Suitable laser protection glasses are required for any activities at the device.
A few common problems that may occur during operation are shown in the following. Here are some sugges-
tions for easy troubleshooting:
The device does not work, no light and the fan does not work
1. Check the power connection and main fuse.
No response to the DMX controller
1. If the display shows a ashing number, for example “001“, no DMX signal is being received. Check the
DMX connectors and cables to see if they are properly linked.
2. If the display does not ash and there is no response, check the address settings and DMX polarity.
3. Try to use another DMX controller.
4. Check if the DMX cables run near or alongside high-voltage cables that may cause damage or interference
to the DMX interface circuit.
If the procedures recommended above do not succeed, please contact our Service Center. You can nd the
contact information at www.thomann.de.
Cleaning
DANGER
Laser radiation!
During cleaning follow the instructions specied in section “Laser safety” on page 4.
DANGER
Laser radiation!
To avoid unintended laser emission, remove the safety key before you start to clean the
device.
Clean the optical lenses which are accessible from the outside periodically to optimise light output. The clean-
ing frequency depends on the environment in which the device operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
• Clean with soft cloth using normal glass cleaning uid.
• Always dry the parts carefully.
• Clean the external optics at least every 20 days.

DJ Lase 40-G MKII / 100-R MKII / 150-B
14
Technical data
The laser emission values shown in the following table were measured according to the IEC measurement
conditions for the classication.
DJ Lase 40-G MKII DJ Lase 100-R MKII DJ Lase 150-B
Item no. 255620 255623 255624
Laser medium Green, 532 nm, Nd: YVO4
DPSS
Red, 650 nm, LD Violet, 405 nm, GaAlAs
Laser power > 40 mW > 100 mW > 150 mW
Laser classication acc. to EN
60825-1 2007
3B
Beam diameter at aperture < 5 mm
Pulse data All pulses < 4 Hz (> 0.25 s)
Divergence (each beam) < 2 mrad
Divergence (total light) < 160°
Number of DMX channels 8
Input voltage 110 VAC … 240 VAC, 50/60Hz
Power consumption 12 W
Fuse 5 mm × 20 mm, 1 A, 250 V, slow characteristic
Dimensions (W × D × H) 160 mm × 160 mm × 80 mm (6.3 in. × 6.3 in. × 3.1 in.)
Weight 1.8 kg (4.0 lbs)

www.thomann.de
DJ Lase 40-G MKII / 100-R MKII / 150-B
15
Protecting the environment
Disposal of the packaging material
For the transport and protective packaging, environmentally friendly materials have
been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed and are not in the
reach of babies and young children. Choking hazard! Do not just dispose these mate-
rials with your normal household waste, but make sure that they are fed to a recovery.
Please follow the notes and markings on the packaging.
Disposal of your old device
Electrical and electronic equipment often contain materials which can be unhealthy
and environmentally harmful, if not properly treated and disposed of. However, they
are essential for the proper operation of your device. At the end of its operating life-
time, do not dispose the device with your normal household waste.
This device is subject to the European directive 2002/96/EC.
Dispose this device through an approved waste disposal rm or through your local
waste facility. When discarding the unit, comply with the rules and regulations that
apply in your country. If in doubt, consult your local waste disposal facility.

© 2011 • Musikhaus Thomann e. K. • Treppendorf 30 • 96138 Burgebrach • Germany • www.thomann.de