Stamina fusion 15-7250 User manual

Model#: 15-7250
STAMINAPRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
allinstructionsarenotfollowed.
Keep others and pets away
from equipment when in use.
Alwaysmakesureallboltsand
nuts are tightened prior to
each use. Follow all safety
instructions in this manual.
When calling for parts or
service, please specify the
following number:
WARNING
CAUTION:
Weight on this product should not exceed 300 lbs.
Owner's
Manual
2008, 08 2008 Stamina Products, Inc.
2040 N. Alliance, Springfield, MO 65803
Customer Service
1 [phone]
www.staminaproducts.com
This Product is Produced Exclusively by

TABLE OF CONTENTS
Safety Instructions 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Set Up Instructions 13
Operational Instructions 14
Computer Instructions 15
Storage 20
Maintenance 20
Conditioning Guidelines 21
Warm-up and Cool-Down 22
Warranty 23
Product Parts Drawing 24
Parts List 25
Fax/Mail Ordering Form 27
Page Page
SAFETY INSTRUCTIONS
To reduce the risk of serious injury, read the following Safety Instructions before
using the Magnetic Fusion 7250 Bike.
WARNING:
2
Before starting any exercise or conditioning program you should consult with your personal
physician to see if you require a complete physical exam.This is especially important if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.
WARNING:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Read all warnings posted on the Magnetic Fusion 7250 Bike.
The Magnetic Fusion 7250 Bike should only be used after a thorough review of the Owner's Manual.
We recommend that two people be available for assembly of this product.
Keepchildrenawayfromthe Magnetic Fusion 7250 Bike. Donot allow childrentouseor play ontheMagnetic
Fusion 7250 Bike. Keep children and pets away from the Magnetic Fusion 7250 Bike when it is in use.
TheMagnetic Fusion 7250 Bike isnotafreewheelingexercisebike;therefore,pedalspeedshouldbereduced
in a controlled manner to prevent injury from spinning pedals.
Make sure the Magnetic Fusion 7250 Bike is properly assembled and that all nuts and bolts are tightened
before use.
It is recommended that you place this exercise equipment on an equipment mat.
Set up and operate the Magnetic Fusion 7250 Bike on a solid level surface. Do not position the Magnetic
Fusion 7250 Bike on loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the Magnetic Fusion 7250 Bike.
AdjusttheFOOT STANDS(64) and STAND(68) sothattheMagnetic Fusion 7250 Bikesitsonthe floor without
rocking. See page 13 for detailed leveling instructions.
Before using, inspect the Magnetic Fusion 7250 Bike for worn or loose components, and tighten or replace
any loose or worn components prior to use.
Before using, always check the SEAT CARRIAGE(7) to be sure it is secure. TheADJUSTMENT KNOB(49)
must be inserted into one of the holes in the REAR FRAME(5) and tightened.
Each user should adjust the seat per instructions on page 14.
Do not attempt to adjust the seat while you are on the Magnetic Fusion 7250 Bike.
Consultaphysicianpriortocommencinganexerciseprogram andfollowhis/herrecommendationsindeveloping
your fitness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop and consult
yourphysician.
Follow your physician's recommendations in developing your own personal fitness program.
Alwayschoose the workoutwhich best fitsyourphysicalstrength andflexibilitylevel.Know your limitsandtrain
within them.Always use common sense when exercising.
Do not wear loose or dangling clothing while using the Magnetic Fusion 7250 Bike.
Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross training
shoes that fit well, provide foot support, and feature non-skid rubber soles.
Care should be taken in mounting or dismounting the Magnetic Fusion 7250 Bike.
The Magnetic Fusion 7250 Bike should not be used by persons weighing over 300 pounds.
The Magnetic Fusion 7250 Bike should be used by only one person at a time.
Do not ride the Magnetic Fusion 7250 Bike while standing up.
The Magnetic Fusion 7250 Bike is for consumer use only. It is not for use in public or semipublic facilities.

THANK YOU FOR PURCHASING THE
Magnetic Fusion 7250 Bike
To help you get started, we have pre-assembled most of your
Magnetic Fusion 7250 Bike at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 [phone]
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
CALL US FIRST
Customer Service
1(800)375-7520
www.staminaproducts.com
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springfield, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[e-mail]
www.staminaproducts.com
3

BEFORE YOU BEGIN
4
Seat
Foot Cap
Right Crank
Right Cover
Back Cushion
Foot Cap
Seat Frame
Seat Carriage Right Pedal
Left Pedal
Upright Sleeve
Front Frame
Computer
Warning Label
Thank you for choosing the Magnetic Fusion 7250
Bike. We take great pride in producing this quality
productandhopeit will provide many hours ofquality
exercise to make you feel better, look better, and
enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health. Too
often,our busylifestyleslimitourtimeandopportunity
to exercise. The Magnetic Fusion 7250 Bike
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the
Magnetic Fusion 7250 Bike.
Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Magnetic Fusion 7250
Bike, please do not return the product. Contact us
FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
ServiceStaff is availabletoassistyou from 7:30A.M.
to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00A.M. to 3:00 P.M. (Central Time)
on Friday.
If you would like to contact us online, go to our
websiteat www.staminaproducts.comandaccessthe
Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.
Upright
Rear Covers
Adapter
Seat Rail
Left Pedal Strap
Handrail
Water Bottle Handlebar
Pulse Sensor
Foot Cap
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Allen Wrench (5mm)
Allen Wrench (6mm)
Multi-opening Wrench

EQUIPMENT WARNING & NOTICE LABELS
This chart is provided to help identify the warning & notice labels on the Magnetic Fusion 7250 Bike.
Please take a moment to familiarize yourself with all of the warning & notice labels.
Label is larger than actual size
WARNING LABEL(109)
W1
5

HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers or the
ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the
length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat heads,
is measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.
mm.
in.
INCHES
MILLIMETERS
11/2021/2 31/2 41/2 51/2 61/2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
6 8 10 12
3/16" 5/16" 1/2"3/8"1/4"
length
length
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.
66
Part No. and Description Qty
103 Washer (M8) 4
76 Bolt, Button Head (M10 x 1.5 x 200mm) 2
70 Bolt, Button Head (M8 x 1.25 x 40mm) 1
71 Bolt, Button Head (M8 x 1.25 x 45mm) 2
72 Bolt, Button Head (M8 x 1.25 x 53mm) 4
75 Bolt, Button Head (M10 x 1.5 x 53mm) 3
78 Bolt, Flat Head (M6 x 1 x 12mm) 2
82 Bolt, Round Head (M6 x 1 x 38mm) 8
85 Screw, Round Head (M4 x 0.7 x 15mm) 10
86 Screw, Round Head (M5 x 0.8 x 15mm) 4
97 Acorn Nut (M10 x 1.5) 2
98 Arc Washer (M8) 2
99 Arc Washer (M10) 8
100 Lock Washer (M8) 6
101 Lock Washer (M10) 9
79 Bolt, Flat Head (M8 x 1.25 x 15mm) 6
74 Bolt, Button Head (M10 x 1.5 x 20mm) 4

ASSEMBLY INSTRUCTIONS
7
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materials from your area and place them back into the box.Do not dispose of the packing materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please call
ourtoll-freenumberforassistance1-800-375-7520 or e-mail us at [e-mail].
STEP 1
Makethe WHEEL(62) onthe FRONT STABILIZER(2) facethefront, then attachthe FRONT STABILIZER(2)
totheFRONT FRAME(1) with BUTTON HEAD BOLTS(M8x1.25x53mm)(72), LOCKWASHERS(M8)(100),
and WASHERS(M8)(103).
STEP 2
Slide the FOOT CAPS(63) onto both ends of the FRONT STABILIZER(2) so they fit over the edges of the
LEFT and RIGHT COVERS(33, 34) andsecurewith ROUND HEAD SCREWS(M4x0.7x15mm)(85). Screw
the FOOT STANDS(64) all the way up into the FRONT STABILIZER(2) on both sides.

8
ASSEMBLY INSTRUCTIONS
STEP 3
Attach the REAR STABILIZER(6) to the REAR FRAME(5) with BUTTON HEAD BOLTS(M8x1.25x53mm)
(72), LOCK WASHERS(M8)(100), and WASHERS(M8)(103).
STEP 4
Slide the FOOT CAPS(63) onto both ends of the REAR STABILIZER(6) so they fit over the edges of the
LEFT and RIGHT REAR COVERS(65, 66) and securewith ROUND HEAD SCREWS(M4x0.7x15mm)(85).
Screw the FOOT STANDS(64) all the way up into the REAR STABILIZER(6) on both sides.
STEP 5
Screw the STAND(68) all the way up into the bottom of the FRONT FRAME(1).Connect the PULSE
EXTENSIONWIRE(43) tothe CONTROLWIRE(25).InserttheFRONT FRAME(1) intotheREAR FRAME(5)
and secure with BUTTON HEAD BOLTS(M10x1.5x20mm)(74), BUTTON HEAD BOLTS(M10x1.5x53mm)
(75), ARC WASHERS(M10)(99), and LOCK WASHERS(M10)(101). Press the COVER PLUGS(67) into
the holes in the LEFT and RIGHT REAR COVERS(65, 66).
NOTE: See page 13 for detailed leveling instructions to prevent rocking.
Rear Frame(5), is
inside of Rear
Covers(65, 66)

9
ASSEMBLY INSTRUCTIONS
To attach the HANDRAIL(9), position the HANDRAIL(9) under the SEAT CARRIAGE(7) as shown in the
above illustration and secure with BUTTON HEAD BOLTS(M8x1.25x45mm)(71), ARC WASHERS(M8)
(98), and LOCK WASHERS(M8)(100).
STEP 8
Referto theinsetdrawing.PlugthePULSESENSORWIRE(55) intotheSOCKETof thePULSEEXTENSION
WIRE(43) located on the SEAT RAIL(45).
STEP 7
NOTE: The PULSE SENSOR WIRES(55) go through the tube of the HANDRAIL(9). Be careful not to
damage the wires when inserting the BUTTON HEAD BOLTS(M8x1.25x45mm)(71) through the
holes in the HANDRAIL(9) when attaching it to the SEAT CARRIAGE(7).
Socket of Pulse
Extension Wire(43)
STEP 6
AttachtheSEAT FRAME(8) totheSEATCARRIAGE(7)withBUTTONHEADBOLTS(M10x1.5x200mm)(76),
WASHERS(M10)(99), LOCK WASHERS(M10)(101), and ACORN NUTS(M10x1.5)(97).

10
ASSEMBLY INSTRUCTIONS
STEP 9
Attach the SEAT(59) and BACK CUSHION(60) to the SEAT FRAME(8) with ROUND HEAD BOLTS
(M6x1x38mm)(82).
STEP 10
Refer to the inset drawing. Press the NUT CAPS(M10)(53) onto the NYLOCK NUTS(M10x1.5)(95) on both
sides of the SEAT CARRIAGE(7).

11
ASSEMBLY INSTRUCTIONS
STEP 11
NOTE: The RIGHT PEDAL(41) has Rstamped on the end of the pedal shaft. The RIGHT PEDAL(41) has
right hand threads and is tightened by turning clockwise. The LEFT PEDAL(39) has Lstamped on
the end of the pedal shaft. The LEFT PEDAL(39) has left hand threads and is tightened by turning
counterclockwise.
Thread the RIGHT PEDAL(41) into the RIGHT CRANK(36) as shown. Tighten the pedal securely. Select
the RIGHT PEDAL STRAP(42) which has Rmarked on it. Snap the two hole end to the inside edge of the
RIGHT PEDAL(41). Insert the other end of the strap through the slot and snap the strap to the hook on the
outside edge of the RIGHT PEDAL(41). Select adjustment holes which allow your foot to be easily removed
from the pedals.
Use the same procedure to attach the LEFT PEDAL(39) to the LEFT CRANK(35) and snap the LEFT
PEDAL STRAP(40) to the LEFT PEDAL(39).
STEP 12
Slide the UPRIGHT SLEEVE(32) over the UPRIGHT(3). Connect the CONNECTION WIRE(26) to the
CONTROL WIRE(25). Insert the UPRIGHT(3) onto the FRONT FRAME(1) and secure with FLAT HEAD
BOLTS(M8x1.25x15mm)(79). Slide the UPRIGHT SLEEVE(32) down to cover the bolt heads.

12
ASSEMBLY INSTRUCTIONS
Socket of
Power Wire(28)
A.
B.
STEP 13
Referto illustrationA.Run theCONNECTIONWIRE(26) throughthe holeintheplateon the HANDLEBAR(4).
Attach the HANDLEBAR(4) to the UPRIGHT(3) with BUTTON HEAD BOLT(M8x1.25x40mm)(70) and
FLAT HEAD SCREWS(M6x1x12mm)(78).
STEP 14
Plug the CONNECTION WIRE(26) into the EXTENSION WIRE on the COMPUTER(27). Attach the
COMPUTER(27) to the plate on the HANDLEBAR(4) with ROUND HEAD SCREWS(M5x0.8x15mm)(86).
STEP 15
Attach the MOUNTING BRACKET(106) to the UPRIGHT(3) with ROUND HEAD SCREWS
(M4x0.7x15mm)(85). Place the WATER BOTTLE(107) in the MOUNTING BRACKET(106).
STEP 16
Refer to illustration B. Plug the ADAPTER(105) into the SOCKET of the POWER WIRE(28) located on the
front of the bike. Plug the ADAPTER(105) into an electrical outlet.

13
SET UP INSTRUCTIONS
Placethe Magnetic Fusion 7250 Bike inthe area whereitwillbeused. It is recommendedthat the Magnetic
Fusion 7250 Bike be placed on an equipment mat. The Magnetic Fusion 7250 Bike is approximately 55 3/4
inches long x 24 3/8 inches wide x 50 3/8 inches tall (max.). (These dimensions may vary up to one inch.)
An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic Fusion 7250 Bike. Make
sure that adequate space is available for access to and passage around the Magnetic Fusion 7250 Bike.
To level the Magnetic Fusion 7250 Bike, first screw the STAND(68) located in the middle of
the FRONT FRAME(1) all the way up into the FRONT FRAME(1) so that it is not touching the
floor. Adjust the four FOOT STANDS(64) on each of the four corners, two under FRONT
STABILIZER(2) and two under the REAR STABILIZER(6). When the FOOT STANDS(64)
are adjusted and the Magnetic Fusion 7250 Bike is stable, rotate the STAND(68) to make it
contact with the floor.
While you are adjusting the FOOT STANDS(64) the STAND(68) must not be in contact with
the floor. Only after the Magnetic Fusion 7250 Bike has been stabilized with the FOOT
STANDS(64) will you position the STAND(68) so it is in contact with the floor to provide extra
stability for the frame.
The Magnetic Fusion 7250 Bike has a WHEEL(62) on the FRONT STABILIZER(2). Lift up
the REAR STABILIZER(6) to move the Magnetic Fusion 7250 Bike.
LEVELING:
MOVING:
EQUIPMENT MAT
(not included)
FUNCTION INSPECTION:
Visuallyinspectthe Magnetic Fusion 7250 Bike toverifythatassembly is as shown in the aboveillustration.
Check the function of the Magnetic Fusion 7250 Bike by turning the crank slowly through one complete
revolutiontoverifythat the drive train functionsproperly. Use the UP and DOWN buttonsontheCOMPUTER
(27) to select a program and verify that the Magnetic System provides different tensions. Refer to the
COMPUTER INSTRUCTIONS on pages 15 to 19.
Locate and read the WARNING LABEL(109) on the Magnetic Fusion 7250 Bike. Make sure
that all users read the WARNING LABEL(109).
CAUTION:

14
OPERATIONAL INSTRUCTIONS
SEAT ADJUSTMENT
LOAD ADJUSTMENT
CAUTION:
1.
2.
Rotate the ADJUSTMENT KNOB(49) counterclockwise until the pin releases when the knob is pulled.
Pull the ADJUSTMENT KNOB(49) and slide the SEAT CARRIAGE(7) up or down to desired position.
Lock the SEAT CARRIAGE(7) in position by inserting the pin of the ADJUSTMENT KNOB(49) into one
of the adjustment holes in the SEAT RAIL(45), then rotate the ADJUSTMENT KNOB(49) clockwise to
lock the SEAT CARRIAGE(7) securely.
Sit on the seat and place your feet on the pedals. You should be able to move through a complete pedal
stroke without locking your knees or shifting your hips on the seat. The seat is too close to the pedals if
you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat is too far from
the pedals if you have to completely straighten your knees at the bottom of the pedal stroke.
1.
2.
Properseatadjustmentisimportant.Thereare nineadjustmentholesintheSEATRAIL(45).Theseadjustment
holes allow users to adjust the position of the seat for efficient exercise.
Do not attempt to adjust the seat while you are on the Magnetic Fusion 7250 Bike.
Always tighten the ADJUSTMENT KNOB(49) after adjusting the seat to a new position.
The load level of Magnetic Fusion 7250 Bike can be changed at any time during your workout. Use the UP
and DOWN buttons on the COMPUTER(27) to increase or decrease your intensity level. Press the UP
button to increase the load level. Press the DOWN button to decrease the load level.

COMPUTER INSTRUCTIONS
Your Magnetic Fusion 7250 Bike utilizes a magnetic braking system to create resistance for your workout.
You control the amount and pattern of this resistance by means of the advanced computer console mounted
at the center of the handlebar. We recommend that you use this computer console to vary your workout
from session to session and note your progress toward your fitness goals.When used regularly in this way,
the computer console can become an important source of motivation and interest which will help keep you
on track.
The Magnetic Fusion 7250 Bike has twelve preset workout programs. Select the
desired program from the twelve buttons on the computer.
Press to increase the values of the setting mode. Press to increase the level of the
workload when running a program.
Press to decrease the values of the setting mode. Press to decrease the level of
the workload when running a program.
Press to select the values of the various settings.
Press to start the selected program. Press the START/STOP button to stop the
program. Press and holdthe START/STOP button down for four seconds to reset
all of the function values to zero.
PROGRAM BUTTONS:
/UP:
/DOWN:
ENTER:
START/STOP:
BUTTONS:
15

16
COMPUTER INSTRUCTIONS
LCD DISPLAY INSTRUCTIONS
Displays the selected program during exercise, from P1 to P12.
Displays the time. Counts upward from one second to 99:59 minutes. Counts down from
preset value.
Displays the current speed from zero to 99.9 miles per hour.
Displays the distance from zero to 999.9 miles.
Displays the calorie consumption from zero to 999.9 Kcal.
NOTE: The calorie readouts are an estimate for an average user. It should be used only as
a comparison between workouts on this unit.
When you select the Heart Rate Control Programs, P11 or P12, you must input your age.
This value affects only the Heart Rate Control Programs. Press ENTER button until the
AGE/TARGET H.R. display is flashing and use "/ " buttons to input your age.
When Heart Rate Control Programs, P11 or P12, are selected, the target heart rate value
will be shown during exercise.
Displays heart rate in beats per minute from 40 to 240 beats per minute.
To display the heart rate, you must grasp the Pulse Sensors on both sides of the handrail,
one in each hand. The heart symbol " " will begin flashing when the computer senses your
heart rate. Your heart rate will be displayed approximately five (5) seconds after the heart
icon is displayed. If you do not place your hands correctly and 60 seconds passes without
a heart rate reading, the computer will turn off the heart rate circuit. If this occurs, press the
ENTER button to restart the heart rate circuit, place your hands back on the Pulse Sensors
correctly, and the heart rate readout will appear.
PROGRAM:
TIME:
SPEED:
DISTANCE:
CALORIE:
AGE/
TARGET H.R.:
HEART RATE:
PROGRAMNUMBER HEART RATE CONTROL PROGRAMS
CALORIE
AGE/TARGET H.R.
HEART SYMBOL
PROGRAM PROFILE
SPEED
TIME
HEART RATE
DISTANCE

17
COMPUTER INSTRUCTIONS
PROGRAM DESCRIPTIONS
(P1) MANUAL
PRESET PROGRAMS: P2 to P10 are preset automatic programs. The profiles are shown on the face of
the computer. Use the ""button to increase the load level of the program. Use the " " button to decrease
the load level of the program.
MANUAL PROGRAM: P1 is a manual program allowing the user to have
full manual control of the workload. Use the " " button to increase the
load. Use the " " button to decrease the load.
This computer contains 12 different programs. You can preset the program time and the computer will
divide the time chosen into 10 intervals. If you do not set the program time in advance, the computer will
default to a 30 minute workout time.
(P2) ROLLING (P3) VALLEY (P4) FAT BURN
(P5) RAMP (P6) FITNESS (P7) RANDOM
(P8) PLATEAU (P9) INTERVAL (P10) MOUNTAIN

COMPUTER INSTRUCTIONS
(P11) 60% MAX H.R. (P12) 85% MAX H.R.
18
As you exercise, the program will monitor your pulse
and adjust the workload automatically to keep you
working within a zone that is plus or minus 5 beats per
minute of your target heart rate. Your age and the
program you selected will determine your heart rate
zone.
For example, if your age is 30, your maximum heart
rateis 190. If you selectedP11, your workoutwill keep
youwithinatargetheartrate zone that is plus or minus
5 beats per minute of 60% of your maximum heart
rate: 190 x 60% = 114 so your heart rate zone is 109
to 119. The program will monitor your pulse and adjust
the workload automatically to keep your pulse within
the heart rate zone during your workout.
HEART RATE CONTROL PROGRAMS: P11 and P12 are preset automatic Heart Rate Control Programs.
You must input your age and always hold the pulse sensors on the HANDRAIL(9) with both hands when
using the Heart Rate Control Programs. P11 is programmed to use 60% of your maximum heart rate as
your target heart rate zone workout goal, and P12 is programmed to use 85% of your maximum heart rate
as your target heart rate zone workout goal; therefore, P11 will be a less intense workout than P12.

COMPUTER INSTRUCTIONS
STEP 1: POWER ON
Pedaling or press any button.
COMPUTER OPERATION
STEP 2 : SELECT PROGRAM
Select and press one of the PROGRAM BUTTONS to enter the desired program.
STEP 3: SET THE PROGRAM TIME OR CALORIE (and input age for Heart Rate Control Programs)
The TIME function mode will appear with the display flashing "0:00". You have options to do the following:
When you select the Heart Rate Control Programs, P11 or P12, you must input your age. Press ENTER
button until the AGE/TARGET H.R. display is flashing and use "/ " buttons to input your age. Press the
ENTER button to confirm the setting. Press the START/STOP button to start the program.
Use "/ " buttons to set the program time, from one minute up to 99 minutes with 1 minute increments.
Or, you can keep TIME as "0:00" and press the ENTER button to enter the mode to set the CALORIE.
Use "/ " buttons to set the CALORIE, from 10 Kcal. up to 9990 Kcal. with 10 Kcal. increments. Press
the ENTER button to confirm the setting. Press the START/STOP button to start the program.
1. Press START/STOP button to start the program. All of the function values will count up from zero.
2.
The program will not start until you press the START/STOP button.
The computer will count down from the function values that you set, Time and Calorie. When
one of the two function values counts down to zero, the computer will remind you with an
audible alarm and start counting up this function value. Another function value will continue to
count down.
If you don't set the program time, the computer will count up from one second up to 99:59
minutes, and use the default workout time, 30 minutes, to cycle run the program profile.
1.
2.
3.
NOTE:
POWER SOURCE:
The computer uses the ADAPTER(105) as a power source. Use the Magnetic Fusion 7250 Bike with the
adapter plugged into an electrical outlet.
OPERATION DESCRIPTIONS
To stop a running program, press the START /STOP button. In this mode, you can press the
START /STOP button again to continue to run the current program. Or, you can use the PROGRAM
BUTTONS to select a new program. The function values of DISTANCE and CALORIE will continue to
accumulate.
When you complete a program, press the START/STOP button to stop the program. You can use the
PROGRAM BUTTONS to select a new program. The function values of DISTANCE and CALORIE will
continue to accumulate. This will allow you to run several programs and still know the total DISTANCE
and CALORIE during the workout.
If you want to restart with a new program, press and hold the START /STOP button down for four
seconds to reset all of the function values to zero. Use the PROGRAM BUTTONS to select a new
program.
The computer will shut off automatically after 4 minutes of inactivity, and the function values, DISTANCE
and CALORIE, will be kept.
1.
2.
3.
4.
19

20
STORAGE
1.
2.
3.
To store the Magnetic Fusion 7250 Bike, simply keep it in a clean dry place.
AdjusttheSEAT CARRIAGE(7) to the lowest position.The Magnetic Fusion 7250 Bikeisapproximately
55 3/4 inches long x 24 3/8 inches wide x 50 3/8 inches tall (max.). These dimensions will vary. Please
measure your Magnetic Fusion 7250 Bike if exact dimensions are needed.
To move the Magnetic Fusion 7250 Bike, lift the REAR STABILIZER(6) and the bike will roll on the
WHEEL(62) on the FRONT STABILIZER(2).
MAINTENANCE
The safety and integrity designed into the Magnetic Fusion 7250 Bike can only be maintained when the
Magnetic Fusion 7250 Bike is regularly examined for damage and wear. Special attention should be given
to the following:
Use the PROGRAM BUTTONS on the COMPUTER(27) to select a program and verify that the Magnetic
System provides different tensions. The Magnetic System should provide many years of use.
Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that the
left pedal has left hand threads and is tightened by turning counterclockwise. The right pedal has right
hand threads that are tightened by turning clockwise.
Verify that the WARNING LABEL(109) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement WARNING LABEL(109) if it is missing or damaged.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Wornordamaged componentsshallbereplacedimmediatelyortheMagnetic Fusion 7250 Bike removed
from service until repair is made.
Only Stamina Products supplied components shall be used to maintain/repair the Magnetic Fusion
7250 Bike.
Keep your Magnetic Fusion 7250 Bike clean by wiping it off with an absorbent cloth after use.
1.
2.
3.
4.
5.
6.
7.