Stanley DS06 User manual

DS06
HYDRAULIC
DIAMOND SAW
SAFETY, OPERATION AND MAINTENANCE
SERVICE MANUAL
WARNING
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie OR 97267-5698
503-659-5660
FAX [phone]
www.stanley-hydraulic-tools.com
Copyright © 2005, The Stanley Works
OPS/MAINT USA
34567 8/2005 Ver 3

3
TABLE OF CONTENTS
For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the
back of this manual and ask for a Customer Service Representative.
SERVICING THE STANLEY CONCRETE CHAINSAW: This manual contains safety, operation, and routine
maintenance instructions. Servicing of hydraulic tools, other than routine maintenance, must be per-
formed by an authorized and certified dealer. Please read the following warning.
SERIOUS INJURY OR DEATH COULD RESULT FROM THE IM-
PROPER REPAIR OR SERVICE OF THIS TOOL.
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE
DONE BY AN AUTHORIZED AND CERTIFIED DEALER.
WARNING
CERTIFICATE OF CONFORMITY ............................................................................................................................................................................4
SAFETY SYMBOLS ..................................................................................................................................................................................................5
SAFETY PRECAUTIONS..........................................................................................................................................................................................6
TOOL STICKERS & TAGS ........................................................................................................................................................................................8
HYDRAULIC HOSE REQUIREMENTS.....................................................................................................................................................................9
HTMA REQUIREMENTS.........................................................................................................................................................................................10
OPERATION............................................................................................................................................................................................................ 11
PREOPERTION PROCEDURES ............................................................................................................................................................................ 11
CHECK THE POWER SOURCE ............................................................................................................................................................................. 11
CHECK TOOL.......................................................................................................................................................................................................... 11
CONNECT HYDRAULIC HOSES............................................................................................................................................................................ 11
CONNECTING TO A WATER SUPPLY ................................................................................................................................................................... 11
CHECK CHAIN AND BAR ADJUSTMENT .............................................................................................................................................................. 11
CHECK CHAIN SEGMENT WEAR .........................................................................................................................................................................12
OPERATING PROCEDURES .................................................................................................................................................................................12
PLAN THE CUT.......................................................................................................................................................................................................12
TYPES OF CUTS ....................................................................................................................................................................................................13
COLD WEATHER OPERATION ..............................................................................................................................................................................13
USING THE WALL WALKER™ ...............................................................................................................................................................................13
MAINTENANCE & ADJUSTMENTS........................................................................................................................................................................14
GENERAL MAINTENANCE TIPS............................................................................................................................................................................14
SAW BAR RAIL .......................................................................................................................................................................................................14
ROTATING THE SAW BAR .....................................................................................................................................................................................14
CHAIN TENSION ADJUSTMENT............................................................................................................................................................................14
SERVICING THE CHAIN.........................................................................................................................................................................................15
MAINTENANCE & ADJUSTMENTS........................................................................................................................................................................15
MAINTENANCE & ADJUSTMENTS........................................................................................................................................................................16
REPLACING THE CHAIN BREAKER PUNCH........................................................................................................................................................16
SPINNING RIVETS .................................................................................................................................................................................................16
NOSE SPROCKET DISASSEMBLY AND ASSEMBLY ...........................................................................................................................................17
MAINTENANCE & ADJUSTMENTS........................................................................................................................................................................17
TOOL EQUIPMENT & CARE ..................................................................................................................................................................................19
TROUBLESHOOTING.............................................................................................................................................................................................20
SPECIFICATIONS ...................................................................................................................................................................................................22
ACCESSORIES.......................................................................................................................................................................................................22
SERVICE .................................................................................................................................................................................................................23
MOTOR INSPECTION AND CLEANING.................................................................................................................................................................24
BAR & CHAIN AND CHAIN GUARD ASSEMBLY ...................................................................................................................................................26
DS06 PARTS ILLUSTRATION ................................................................................................................................................................................27
DS06 PARTS LIST ..................................................................................................................................................................................................28
DS06 PARTS ILLUSTRATION ................................................................................................................................................................................29
DS06 PARTS LIST ..................................................................................................................................................................................................30
DIAMOND CHAIN APPLICATIONS.........................................................................................................................................................................31
WARRANTY ............................................................................................................................................................................................................32

4
CERTIFICATE OF CONFORMITY
ÜBEREINSTIMMUNGS-ZERTIFIKAT
CERTIFICAT DE CONFORMITE CEE
CERTIFICADO DE CONFORMIDAD
CERTIFICATO DI CONFORMITA
Hydraulic Tools
______________________________________________________________________
I, the undersigned:
Ich, der Unterzeichnende:
Je soussigné:
El abajo firmante:
lo sottoscritto:
Schultz, Theodore J.
Surname and First names/Familiennname und Vornamen/Nom et prénom/Nombre y apellido/Cognome e nome
hereby certify that the construction plant or equipment specified hereunder:
bestätige hiermit, daß das im folgenden genannten Werk oder Gerät:
certifies par ceci que l’ usine ou l’ équipement de construction indiqué cidessous:
por el presente certifico que la fabrica o el equipo especificado a continuacion:
certifico che l’impianto o l’attrezzatura sotto specificata:
1. Category: Concrete Cutting Chainsaw
Kategorie:
Catégorie:
Categoria:
Categoria:
2. Make/Ausführung/Marque/Marca/Marca
Stanley
3. Type/Typ/Type/Tipo/Tipo: DS06200001, DS06300001
4. Serial number of equipment:
Seriennummer des Geräts:
Numéro de série de l’équipement:
Numero de serie del equipo:
Matricola dell´attrezzatura:
All
5. Year of manufacture/Baujahr/année de fabrication/Año de fabricacion/Anno di fabbricazione 1998
Has been manufactured in conformity with - EEC Type examination as shown.
Wurde hergestellt in Übereinstimmung mit - EEC Typ-Prüfung nach.
Est fabriqué conformément - au(x) type(s) examiné(s) comme indiqué dans le tableau ci-après.
Ha sido fabricado de acuerdo con - tipo examen EEC como dice.
E’ stata costruita in conformitá con - le norme CEE come illustrato.
Examen CEE de type
Directive
Richtlinie
Directives particulières
Directriz
Direttiva
No.
Nr
Numéro
No
n.
Date
Datum
Date
Fecha
Data
Approved body
Prüfung durch
Organisme agréé
Aprobado
Collaudato
Date of expiry
Ablaufdatum
Date d´expiration
Fecha de caducidad
Data di scadenza
Machinery Directive
EN
ISO
ISO
ISO
98/37/EC
89/392/CEE
292
8662-1
3744
10726
1998
1991
1988
1994
1992
Self
Self
Self
Self
Self
Self
NA
NA
NA
NA
NA
NA
6. Special Provisions: None
Spezielle Bestimmungen:
Dispositions particulières:
Provisiones especiales:
Disposizioni speciali:
Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data 3/98
Signature/Unterschrift/Signature/Firma/Firma____________________________________________________________________________
Position/Position/Fonction/Puesto/Posizione Engineering Manager
P/N 62310 rev 03 3/05

5
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair
actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip-
ment.
This safety alert and signal word indicate an imminently hazardous situa-
tion which, if not avoided, will result in death or serious injury.
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONS
Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte-
nance personnel.
CAUTION
WARNING
DANGER
NOTICE
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, may result in minor or moderate injury.
This signal word indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
This signal word indicates a situation which, if not avoided, will result in
damage to the equipment.
This signal word indicates a situation which, if not avoided, may result in
damage to the equipment.
IMPORTANT
SAFETY SYMBOLS

6
Tool operators and maintenance personnel must always comply with the safety
precautions given in this manual and on the stickers and tags attached to the tool
and hose.
These safety precautions are given for your safety. Review them carefully before
operating the tool and before performing general maintenance or repairs.
Supervising personnel should develop additional precautions relating to the specific
work area and local safety regulations. If so, place the added precautions in the
space provided on page 5.
The DS06 Diamond Chain Saw will provide safe and dependable service if operated
in accordance with the instructions given in this manual. Read and understand this
manual and any stickers and tags attached to the tool and hoses before operation.
Failure to do so could result in personal injury or equipment damage.
• Establish a training program for all operators to ensure safe operation.
• The operator must be familiar with all prohibited work areas such as excessive slopes and dangerous terrain condi-
tions.
• Do not operate the chain saw unless thoroughly trained or under the supervision of an instructor.
• Always wear safety equipment such as goggles, ear, head protection, leg protection, gloves, snug fitting clothing and
safety shoes at all times when operating the chain saw.
• Do not overreach. Maintain proper footing and balnace at all times.
• Do not inspect or clean the chain saw while the hydraulic power source is connected. Accidental engagement of the
chain saw can cause serious injury.
• Always connect hoses to the chain saw hose couplers before engergizing the hydraulic power source. Make sure all
hose connections are tight.
• Do not operate the chain saw at fluid temperatures above 140°F/60°C. Operation at higher temperatures can cause
higher than normal temperatures at the chain saw which can result in operator discomfort.
• Do not rely exclusively upon the safety devices built into the chain saw. As a chain saw user, several steps must be
taken to keep your cutting jobs free from accident or injury:
1. With a basic understanding of kickbacks, you can reduce or eliminate the element of surprise. Sudden surprise
contributes to accidents.
2. Keep a good firm grip on the chain saw with both hands, the right hand on the rear handle and the left hand on
the front handle when operating the chain saw. Use a firm grip with thumbs and fingers encircling the chain saw
handles. A firm grip helps reduce kickbacks and maintains control of the chain saw. Do not let go.
3. Make sure the area in which you are cutting is free of obstructions.
4. Cut at rated operating speeds (gpm).
5. Do not overreach or cut above shoulder height.
6. Only use replacement bars and chains specified by Stanley or the equivalent.
• Make sure the chain guard is in place before operating the chain saw.
SAFETY PRECAUTIONS

7
• Remove or control the water slurry to prevent yourself or others from slipping while cutting.
• Provide adequate ventilation in closed areas when operating a gas or diesel hydraulic power source.
• Always be well rested and mentally alert before operating the chain saw.
• Do not allow bystanders near the chain saw when starting or cutting.
• Do not start cutting until you have a clear work area and secure footing.
• Keep all parts of the body away from the chain saw during operation.
• Carry the chain saw with the tool deenergized and the bar and chain to the rear of your body.
• Do not operate a chain saw that is damaged, improperly adjusted, or not completely and securely assembled. Make
sure the chain stops moving when the control trigger is released.
• Keep the handle dry, clean and free of hydraulic fluid.
• Do not use the chain saw near energized transmission lines.
• Turn off the power source or move the hydraulic control valve to neutral before setting the chain saw down.
• Use a guide bar scabbard when transporting the chain saw.
• Know the location of buried or covered electrical services before starting work.
• To avoid personal injury or equipment damage, all chain saw repair, maintenance and service must only be performed
by authorized and properly trained personnel.
• Make sure the chain breaker and rivet spinner are securely mounted on flat, clean work surfaces. Check the mounting
screws/bolts often.
• Check all chain breaker and rivet spinner components regularly for wear and general condition.
SAFETY PRECAUTIONS

8
The safety tag (p/n
15875) at right is attached
to the tool when shipped
from the factory. Read
and understand the safety
instructions listed on this
tag before removal. We
suggest you retain this tag
and attach it to the tool
when not in use.
TOOL STICKERS & TAGS
12412
Warning Decal
DANGER
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE OPERA-
TION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED
AS NON-CONDUCTIVE WHEN USING HYDRAULIC TOOLS
ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH
OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT
LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART-
MENT INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION
INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL
INJURY.
A DO NOT EXCEED SPECIFIED FLOW AND PRESSURE FOR
THIS TOOL. EXCESS FLOW OR PRESSURE MAY CAUSE A
LEAK OR BURST.
B DO NOT EXCEED RATED WORKING PRESSURE OF HY-
DRAU LIC HOSE USED WITH THIS
TOOL. EXCESS PRESSURE MAY
CAUSE A LEAK OR BURST.
C CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY
FOR LEAKS. DO NOT FEEL FOR LEAKS WITH YOUR
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE OPERA-
TION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
D DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CONNECTED
TO THE TOOL BEFORE PRESSURING SYSTEM. SYSTEM
PRESSURE HOSE MUST ALWAYS BE CONNECTED TO TOOL
“IN” PORT. SYSTEM RETURN HOSE MUST ALWAYS BE
CONNECTED TO TOOL “OUT” PORT. REVERSING CONNEC-
TIONS MAY CAUSE REVERSE TOOL OPERATION WHICH CAN
RESULT IN SEVERE PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-CEN-
TER HYDRAULIC SYSTEMS. THIS MAY RESULT IN LOSS OF
OTHER HYDRAULIC FUNCTIONS POWERED BY THE SAME
SYSTEM AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA. KEEP
BYSTANDERS CLEAR OF YOUR WORK AREA.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PROTEC-
TION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL
TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE
PERFORMED BY AUTHORIZED AND PROPERLY TRAINED
PERSONNEL.
(shown smaller then actual size)
SAFETY TAG P/N 15875
DANGER
33445
Name Tag Decal
28323
CE Decal
11212
Sound Level Decal
11206
Circuit “C” Decal
11207
Circuit “D” Decal
Lwa
D
30 LPM @ 138 B AR
EHTMA CATEGORY
Failure to use hydraulic hose labeled and certified
Failure to use hydraulic hose labeled and certified
as non-conductive when using hydraulic tools on
as non-conductive when using hydraulic tools on
or near electric lines may result in death or
or near electric lines may result in death or
For proper and safe operation read owners manual
For proper and safe operation read owners manual
and mwke sure that you have been properly
and mwke sure that you have been properly
trained in correct procedures required for work
trained in correct procedures required for work
serious injury.
serious injury.
on or around electric lines.
on or around electric lines.
ELECTROCUTION
HAZARD
DANGER
11212
12412
11206 11207
28409
28323
33445
28409
Composite Decal

9
HOSE TYPES
Hydraulic hose types authorized for use with Stanley Hydraulic Tools are as follows:
➊Certified non-conductive
➋Wire-braided (conductive)
➌Fabric-braided (not certified or labeled non-conductive)
Hose ➊listed above is the only hose authorized for use near electrical conductors.
Hoses ➋and ➌listed above are conductive and must never be used near electrical conductors.
HOSE SAFETY TAGS
To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydrau-
lic Tools. DO NOT REMOVE THESE TAGS.
If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be
obtained from your Stanley Distributor.
HOSE PRESSURE RATING
The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the
hydraulic system.
THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE
THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.
HYDRAULIC HOSE REQUIREMENTS
SIDE 1 SIDE 2
D A N G E R
DO NOT REMOVE THIS TAG
D A N G E R
1 FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAYRESULT IN DEATH
OR SERIOUS INJURY.
FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND
ELECTRIC LINES.
2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE ON
OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FITTING
WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOSISTURE AND TEST
HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH SAFETY
DEPARTMENT INSTRUCTIONS.
DO NOT REMOVE THIS TAG
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR
HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP
HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT
DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE
PERSONAL INJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR
CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE
HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO
COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
3(shown smaller than actual size)
(shown smaller than actual size)
D A N G E R
DO NOT REMOVE THIS TAG
D A N G E R
1 DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS
NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.
2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND
ELECTRIC LINES.
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR
HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP
HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT
DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE
PERSONAL INJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT
WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO
PULL OR LIFT TOOLS, POWER UNITS, ETC.
DO NOT REMOVE THIS TAG
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO
COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SEE OTHER SIDE
SIDE 1 SIDE 2

10
HTMA REQUIREMENTS
FLOW RATE
TOOL OPERATING PRESSURE
(at the power supply outlet)
SYSTEM RELIEF VALVE SETTING
(at the power supply outlet)
MAXIMUM BACK PRESSURE
(at tool end of the return hose)
Measured at a max. fluid viscosity of:
(at min. operating temperature)
TEMPERATURE
Sufficient heat rejection capacity
to limit max. fluid temperature to:
(at max. expected ambient temperature)
Min. cooling capacity
at a temperature difference of
between ambient and fluid temps
NOTE:
Do not operate the tool at oil temperatures above 140° F (60° C). Operation at higher temperatures can cause operator
discomfort at the tool.
FILTER
Min. full-flow filtration
Sized for flow of at least:
(For cold temp. startup and max. dirt-holding capacity)
HYDRAULIC FLUID
Petroleum based
(premium grade, anti-wear, non-conductive)
VISCOSITY
(at min. and max. operating temps)
NOTE:
When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the
most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the require-
ments over a wide range of operating temperatures.
*SSU = Saybolt Seconds Universal
4-6 gpm 7-9 gpm 11-13 gpm 9-10.5 gpm
(15-23 lpm) (26-34 lpm) (42-49 lpm) (34-40 lpm)
2000 psi 2000 psi 2000 psi 2000 psi
(138 bar) (138 bar) (138 bar) (138 bar)
2100-2250 psi 2100-2250 psi 2100-2250 psi 2200-2300 psi
(145-155 bar) (145-155 bar) (145-155 bar) (152-159 bar)
250 psi 250 psi 250 psi 250 psi
(17 bar) (17 bar) (17 bar) (17 bar)
400 ssu* 400 ssu* 400 ssu* 400 ssu*
(82 centistokes) (82 centistokes) (82 centistokes) (82 centistokes)
140° F 140° F 140° F 140° F
(60° C) (60° C) (60° C) (60° C)
3 hp 5 hp 7 hp 6 hp
(2.24 kW) (3.73 kW) (4.47 kW) (5.22 kW)
40° F 40° F 40° F 40° F
(22° C) (22° C) (22° C) (22° C)
25 microns 25 microns 25 microns 25 microns
30 gpm 30 gpm 30 gpm 30 gpm
(114 lpm) (114 lpm) (114 lpm) (114 lpm)
100-400 ssu* 100-400 ssu* 100-400 ssu* 100-400 ssu*
(20-82 centistokes)
TOOL CATEGORY
HYDRAULIC SYSTEM
REQUIREMENTS TYPE 1 TYPEII TYPEIII TYPE RR
NOTE:
These are general hydraulic system requirements. See tool Specification page for tool specific requirements.