STAR TRAC FITNESS Spinner Blade ION Use and care manual

Part Replacement
STAR TRAC FITNESS 1 of 13 637-1498 Rev: A
Generator Flywheel
Spinner
®
Blade ION
Parts Required:
•Spinner
®
Blade ION Generator Flywheel Assembly (PN: 740-8343)
Tools Required:
•Metric Hex Key Wrench Set or Specific Keys
o3mm Hex Key
o4mm Hex Key
o5mm Hex Key
o7mm Hex Key
•Metric Open Wrench Set or Specific Wrenches
o18mm Open End Wrench
•Screw Driver Set or Specific Drivers
o#2 Phillips Screw Driver
o#1 Phillips Screw Driver
oFlat Head Screw Driver
•Tape – Masking, Painters, Scotch, or Clear
Instructions:
1. Remove the user right side external chain guard using a 5mm hex key to unscrew the three socket head cap
screws located on the right side of the Spinner
®
(Fig. 1). Using a #2 phillips head screw driver, remove the two
screws on the user left side of the Spinner
®
(Fig. 2).
Fig. 1 Fig. 2

Part Replacement
STAR TRAC FITNESS 2 of 13 637-1498 Rev: A
2. Remove the two flat head cap screws securing the plastic block caps onto the spring plate and load sensor blocks
from the user right side using a 3mm hex key (Fig 3) and hover the left hand over the left side cap to catch the
unthreading nylock nuts. Once the screws are removed – pop off each cap.
Fig. 3
3. Turn the brake knob counter-clockwise until turning locks and knob moves up and down with ease (Fig. 4).
Fig. 4

Part Replacement
STAR TRAC FITNESS 3 of 13 637-1498 Rev: A
4. Using a flat head screw driver remove retainers on the two master links that join the spring plate blocks (Fig. 5)
and remove spacing plates (Fig. 6).
Fig. 5
Fig. 6
5. Gently slide out the lower spring plate block with the brake pad attached (Fig. 7) and maneuver the assembly at
an angle to pull out and away from Spinner
®
frame (Fig. 8).
Fig. 7
Fig. 8

Part Replacement
STAR TRAC FITNESS 4 of 13 637-1498 Rev: A
6. Push out the remaining master links and store in a safe location (Fig. 9).
Fig. 9
7. Remove the upper load sensor block by removing the two socket head cap screws with a 5mm hex key (Fig. 10).
Fig. 10

Part Replacement
STAR TRAC FITNESS 5 of 13 637-1498 Rev: A
8. Secure the load sensor block assembly to the Spinner
®
frame using tape (Fig. 11).
Fig. 11
9. From the user left side of the flywheel – notice routing of the power & RPM wire harness (Fig. 12).
Fig. 12

Part Replacement
STAR TRAC FITNESS 6 of 13 637-1498 Rev: A
10. Loosen and remove the two button head screws that mount the flywheel adjustment block on the left side of the
flywheel using a 4mm hex key (Fig. 13)
Fig. 13
11. Using the #1 Phillips head screw driver – remove the two Phillips head screws (Fig. 14) that secure the PCB
generator shield to the flywheel.
Fig. 14

Part Replacement
STAR TRAC FITNESS 7 of 13 637-1498 Rev: A
12. Rotate the flywheel clockwise until the flywheel generator wire harness is visible (Fig. 15) and clocked between
the 11 & 12 o’clock position.
Fig. 15
13. Tilt the clear plastic shield (Fig. 16) to expose the four pin connector.
Fig. 16

Part Replacement
STAR TRAC FITNESS 8 of 13 637-1498 Rev: A
14. Using a screw driver for leverage; place it directly over wire harness (Fig. 17) and firmly pull back to separate the
harness connector from the flywheel generator PCB.
Fig. 17
15. From the user right side of the Spinner
®
, take off the finger guard (Fig. 18) by removing the two screws with a #2
phillips screw driver.
Fig. 18

Part Replacement
STAR TRAC FITNESS 9 of 13 637-1498 Rev: A
16. Remove the two socket head cap screws that mount the left side of the center frame support strut using a 7mm
hex key (Fig. 19). In the process; a small bracket that supports the crank sprocket chain guard will become
loose (Fig 20).
Fig. 19
Fig. 20
17. Loosen the two button head screws that mount the flywheel adjustment blocks on both sides of the flywheel using
a 4mm hex key (Fig. 21).
Fig. 21

Part Replacement
STAR TRAC FITNESS 10 of 13 637-1498 Rev: A
18. Completely unscrew the button head screws by hand and remove the flywheel adjustment blocks (Fig. 22). In the
process of removing the adjustment block on the user right side; the center frame support strut will come loose
and will need to be completely removed.
Fig. 22
19. From the user left side of the Spinner
®
; locate and remove the rubber nut cap that covers the flywheel axle
securing hex nut (Fig. 23).
Fig. 23