STAR TRAC FITNESS E-Series MYE User manual

STAR TRAC FITNESS™
E-SERIES INTEGRATED WIRELESS
RECEIVER KIT
OPERATION MANUAL

620-7862 A
Page 2 of 7
REGULATORY INFORMATION
FCC
When used as in conjunction with the appropriate Star Trac cardio equipment, The MYEWIRELESS RECEIVER HAS
been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC rules.
Under the FCC guidelines, operation is subject to the following two guidelines: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
EUROPEAN DIRECTIVES
This product, when used in conjunction with the approved cardio equipment, conforms to the requirements of
the European Council directives:
•89/336/ECC, Electromagnetic Compatibility
•92/590/EEC, General Product Safety Directives
•73/23/EEC, Electrical equipment Low Voltage Safety Directive

620-7862 A
Page 3 of 7
INTRODUCTION
MYE ST-C9 900/800MHz Wireless Receiver allows users to listen to a variety of wall mounted TV’s
connected to 900/800MHz Transmitters as well as an iPod MP3 Player. When an iPod or a USB is
connected to console interface the user will be able to listen to any of the audio sources, TV, iPod, or
USB MP3 files directly through the headphone jack on the main console headphone jack.
CONTROL BUTTONS
POWER BUTTON
Turns Main Console ON/OFF
Note: Each time console is turned ON it will default to wireless receiver mode.
INPUT BUTTON
Allows the user to select between TV, iPod and USB modes
TV Icon - Engages Wireless Receiver Controls & Audio when pressed (default when main
Console is powered ON each time).
KEYPAD TV LED illuminates
DISPLAY TV Icon illuminates when powered ON
CHAN Icon illuminates
Channel Number illuminates 1, 2, 3 etc
iPod Icon - Engages the iPod device if connected. All of the sound from the main console
(regardless of source) will be directed to the headphone jack of the console.
KEYPAD iPod LED illuminates
DISPLAY AUX Icon illuminates
USB Icon – On select models, plays MP3 files from a USB memory stick.
KEYPAD USB LED illuminates
DISPLAY AUX icon illuminates

620-7862 A
Page 4 of 7
BUTTONS
Wireless Receiver Mode:
Scrolls though programmed TV numbers (preset transmitters)
DISPLAY CHAN Icon illuminates – Channel Number illuminates 1, 2, 3 etc
TV Icon illuminates
UP/DOWN BUTTONS
Increases or decreased the volume as selected by the user.
DISPLAY Bar graph depicting volume level in all modes
Note- Volume will default to mid-low level after user unplugs headphone.
EQ BUTTON
Allows the user to scroll between preset equalizer tones. Each time the button is pressed a new EQ
name will light up (the previous will disappear).
DISPLAY EQ Icon always illuminated
Flat, Rock, Jazz, Class, Bass illuminated one at a time
MUTE BUTTON
When the button is pressed the first time the audio MUTES. Pressed a second time turns Mute OFF
and audio comes back ON.
DISPLAY Mute Icon appears when turned ON
Mute Icon disappears when MUTE is OFF
LCD INFORMATION
AUXILIARY MODE
(iPod, USB)

620-7862 A
Page 5 of 7
SET UP INSTRUCTIONS
Transmitter PROGRAMMING MODES (900MHz Version)
During installation the controller must be programmed to lock the TV transmitters. The product is
backwards compatible with all other brands of transmitters so there will be a total of four different
programming modes. In each mode the receiver will automatically scrolls through the frequency
bandwidth and “lock-in” the transmitters. Due to spurious emissions and possible missed transmitters,
a manual mode that enables installer to select individual transmitter channels (each channel is a
designated frequency) and “lock” or “erase” any given channel is also provided.
NOTE: 863MHz version will only have two program modes P-1 for MYE and P-2 for Enercise.
1: To enter transmitter program mode: Press CHANNEL DOWN and VOLUME UP buttons
simultaneously for three seconds. After three seconds the unit will enter program mode.
DISPLAY- “P-1” will pop up on the display after 3 seconds.
2: To select program mode press CH/TRK “+” or “-“ to select one of the program modes.
DISPLAY (900MHz) P-1, P-2, P-3, P-4
P-1 = MYE Entertainment Transmitter Mode
P-2 = Cardio Theater LCS Mode
P-3 = Cardio Theater / Enercise xTV Mode
P-4 = BroadcastVision Mode
DISPLAY (863MHz) P-1, P-2
P-1 = MYE Entertainment Transmitter Mode
P-2 = Enercise
3: To automatically scan and “lock-in” transmitters press INPUT button.
DISPLAY- will show transmitter numbers being scanned in order of frequencies (1, 2, and 3, etc., up
to 32 or 52 for the 900MHz). The total number of channels will correspond to the program mode
selected.
When Scan is complete the controller will default to the first transmitter channel that was found.
DISPLAY- PRESET ICON illuminates
CHAN Icon illuminates
TV (transmitter) Number illuminates
Note: the auto scan may be skipped and the installer may go directly to the manual scan (step 4) by
pressing the EQ button instead of pressing INPUT.
4: The installer may now scroll through all channels to determine if a transmitter was missed or a
spurious emission was picked up. Then “add or delete” a specific transmitter number.
Press CHANNEL UP/DOWN buttons to scroll through all TV (transmitter) numbers within the specified
transmitter mode. Example: Cardio Theater xTV Mode will scroll through a total of 32 channels (each
channel directly relates to a specific frequency).
DISPLAY- PRESET Icon will appear when a specific transmitter channel is programmed. When a
particular transmitter channel is not programmed the PRESET Icon will not appear.

620-7862 A
Page 6 of 7
To Add or Delete a specific transmitter channel press “INPUT” Button. Each time the button is
pressed it will add or delete a transmitter channel.
DISPLAY- PRESET ICON “ON” or “OFF” signifies transmitter channel is added or deleted.
5: To exit program mode press “EQ” button. The display will blank briefly and the unit will default to
first transmitter channel programmed.
DISPLAY- TV Icon illuminates
CHAN Icon illuminates
TV number illuminates
Important Note Regarding Transmitter Channel Program Modes:
The Enercise/Cardio Theater Transmitter Frequency Chart have been provided below for reference.
You will note that the frequencies are set in a particular order starting at number 1 through 32. In most
cased the installers will connect the first transmitter to the first TV and set it to #1. They will move
forward to TV number 2 setting transmitter to #2 and so on. There are instances where a particular
frequency is not performing correctly due to various reasons (spurious emissions, interference from
other sources etc.). So as an example if the installer is at TV 4 but Transmitter channel #4 is not
performing, the installer simply moves to the next Transmitters channel, in this case #5, he/she will
then continue on from there. So in essence a typical 5 TV installation may look like this:
TV-1 / Transmitter Channel #1
TV-2 / Transmitter Channel #2
TV-3 / Transmitter Channel #3
TV-4 / Transmitter Channel #5*
TV-5 / Transmitter Channel #6
In this case we had to skip Transmitter channel #4 due to a problem.
However regardless of the Transmitter channels added or deleted, we must always show the actual
TV numbers in correct sequence. In the case above the wall mounted TV’s will have number signs
under each TV starting at 1 and ending with 5. This is the same method used in our last
Enercise/Cardio Theater software.
TV Frequency TV Frequency
1 905
17 905.6
2 906.2
18 906.6
3 923.6
19 907.6
4 924.4
20 908.8
5 925.6
21 910
6 910.6
22 911.2
7 911.8
23 912.4
8 913.4
24 913.8
9 914.2
25 915
10 915.4
26 916.2
11 917
27 917.4
12 917.8
28 918.4
13 919
29 919.6
14 920.6
30 921
15 921.4
31 921.8
16 922.6
32 923

620-7862 A
Page 7 of 7
TROUBLE SHOOTING:
DISPLAY MESSAGES
Headphone Icon with X through it signifies faulty headphone jack to be replaced. The headphone icon
will come on and flash ON and OFF when the self diagnostic headphone circuit detects a faulty
headphone jack. This flashing indication will remain until it is reset. It may be reset by holding the
POWER button down for three seconds when powering up the console, or by completely removing
power from the console.
SYSTEM RESET
The system can be reset by holding the POWER button down for three seconds at power up. At the
end of the three seconds, the Headphone fault icon displays briefly, indicating that the ‘reset’ has
occurred. The fault condition can also be reset by completely removing power from the console.
RECEPTION RANGE
To change the controller reception to Near/Far, make sure the controller off. Press and hold down the
VOLUME UP button, then press and release the POWER button. Continue holding the VOLUME UP
button for three seconds until ‘LO’ is displayed on the console. This configures the Controller for
“Near” reception. If this procedure is repeated, the display will indicate ‘HI’ and the Controller will be
configured for “Far” reception. The factory default setting is “Far”.