Star Trac E-UB User manual

4 620-7922 Rev B
E-UB Upright Bike
(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS

3 620-7922 Rev B
GENERAL
Before using this product, it is essential to read ALL installation Instructions and this
ENTIRE operations manual; the manual describes equipment setup and instructs
members on how to use it correctly and safely.
1. Multi-end wrench, 10MM/12MM/15MM (Included)
2. Hex (Allen) key, 3MM (Included, E-UB only)
3. Hex (Allen) key, 5MM (Included, E-UB only)
4. Hex (Allen) key, 4MM (Included, E-RB only)
5. Hex (Allen) key, 6MM (Included)
6. Phillips screwdriver, #2 (Included)
7.Torque wrench (not included)
TOOLS REQUIRED
If you are a Factory Certified Installer you must:
• Adhere to all torque and assembly specifications.
• Use a CALIBRATED TORQUE WRENCH with the necessary hex key sockets
• NOT USE a powered drill, powered driver or powered impact tool for any part of the assembly.
• Complete the assembly checklist is completed on each Star Trac product.
• Complete the final programming, functional and cosmetic checklists for each Star Trac product.
FACTORY CERTIFIED INSTALLER
Copyright 2008. Star Trac by Unisen, Inc. Star Trac Fitness, Star Trac®, and the Star Trac Logo are registered trademarks of Unisen Inc. All rights
reserved, including those to reproduce this book or parts thereof in any form without first obtaining written permission from Star Trac.
iPod
®
is a registered trademark of Apple, Inc.
MYE
®
is a registered trademark of MYE Entertainment LLC.
Every effort has been made to keep this information current; however, periodically, changes are made to the information herein, and these changes
will be incorporated into new editions of this publication. All product names and logos are trademarks of their respective owners. Printed in the USA.

5 620-7922 Rev B
Step 1.
Place the box with heavy end facing down in the
area where the unit is going to be assembled.
Cut and remove packaging straps.
Step 2.
Open the box and remove top cover. Then re-
move items from top packaging foam.
(E-UB) UPRIGHT BIKE UNPACKING INSTRUCTIONS
Step 4.
Lift the unit off of the box base and place it on
the floor. Remove packaging materials.
Step 3.
Carefully remove the display and neck assembly
from the box. Unwrap and place the assembly
on a non-scratching surface.

6 620-7922 Rev B
Step 6.
Verify the following components
are included:
1. Bike frame
2. Display console assembly
3. Front and rear feet.
4. Left and right pedals
5. Hardware kit
6. Seat post assembly
7. Owner’s manual, installation
manual and warranty registra-
tion card.
Step 5.
Remove remaining packaging ma-
terials and lay all components on
the floor.
1
2
3
4
5
6
7
Step 8.
Verify the following hardware is included in the kit:
Step 7.
Verify the following tools are included in the kit:
1
2
3
4 5
1 2 3 4
Item Description QTY
1 Multi-end wrench (10MM/12MM/15MM) 1
2 Hex (Allen) key, 6MM 1
3 Hex (Allen) key, 5MM 1
4 Hex (Allen) key, 3MM 1
5 #2 Phillips screwdriver 1
Item Description QTY
1 Screw, M10x30 (Feet Base) 8
2 Screw, M8x20 (Neck Joint) 4
3 Screw, M4x20 (Seat Sleeve) 2
4 Screw, M4 Pan Head (Display Cover) 8

7 620-7922 Rev B
(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS
Step 2.
Install back foot with (4) M10 x 30mm long
button head screws. Tighten all 4 screws to 200
lb-in of torque.
Step 1.
Install front foot with (4) M10 x 30mm long
button head screws. Tighten all 4 screws to 200
lb-in of torque.
Step 4.
Hold and identify left and right pedals.
Note: Left pedal is marked L, right pedal is marked R.
Step 3.
Carefully slide the seat post into the seat tube.
Pull on the seat release knob to allow the seat
to enter the tube. Install (2) M4 x 20mm long
socket head screws into the seat sleeve and
tighten screws to 35 lb-in of torque.
.
Seat Post
M4 Screw
Seat
Release
Knob
Seat
Sleeve
Seat
Tube

8 620-7922 Rev B
Step 8.
Next, un-plug the heart rate cable from the HR
board connector on the display board, then re-
move the front of display.
Note: Place the display in a safe place for later use.
Step 7.
Remove the packaging tape that holds the dis-
play assembly together, then separate the back
of the display from the front.
Step 6.
Attach left pedal to left pedal crank, then tighten
securely.
Note: For left pedal, turn counterclockwise to
tighten.
Step 5.
Attach right pedal to right pedal crank, then
tighten securely.
Note: For right pedal turn clockwise to tighten.

9 620-7922 Rev B
Step 12.
Identify cables coming out of neck and handlebar:
1.Heart rate cable
2.Main I/O cable
3.Coax cable
4.DC power cable
Note: If unit is not equipped with Personal Viewing
Screen, the coax and DC power cables should be
tucked down the neck for possible future use.
Step 11.
Thread in (4) M8 x 20 flat head screws in the
front and back of the neck where the two pieces
came together. Tighten the screws to 150 lb-in
of torque.
Step 10.
Keep hold of the cables and rotate the display
up. Now slide the neck over the two mounts in
the lower neck.
Caution: Take care not to pinch the cables or your
finger when the two pieces come together
Step 9.
Take upper display and neck assembly to the
front of the unit. Feed the cables from the lower
neck through the upper neck.
Note: It may be necessary to have one person sup-
port and position the display while a second person
feeds the cables.
1
2
3
4

10 620-7922 Rev B
Step 16.
Plug the HR ground cable into the quick discon-
nect tab on the display frame.
Step 15.
Next, plug-in the heart rate cable into the HR
board connector.
Step 14.
Plug-in the 12-pin main I/O cable into the front
display circuit board at J4 connector.
Step 13.
Position the display assembly near the top rail
while you make the necessary connections.

11 620-7922 Rev B
Step 20.
Perform a visual inspection, and test the fea-
tures and functions of the unit prior to use.
Note: Refer to the User’s Manual for other settings
and instructions.
Step 19.
Place the unit on the floor in the position it will
be used. Then adjust leveling feet to assure
that the unit is leveled to the floor and does not
rock back and forth.
Step 18.
Next, secure the front display to the back with
(8) M4 Phillips head screws.
Step 17.
Assemble the front and back display parts to-
gether by sliding the bottom of the front display
under the 2 tabs at the base first, then pressing
front display against the back cover.
1
2
YOU HAVE NOW COMPLETED THE (E-UB) UPRIGHT BIKE INSTALLATION
Leveling
Feet

12 620-7922 Rev B
ATTENTION
• Star Trac recommends that the bikes be spaced a minimum of 20.0 inches (0.5 m) apart to allow
safe and easy ingress and egress. Even more importantly, there must be at least 48 inches
(1.25 m) of free space behind the bike.
• As with any motorized equipment, the area where bikes are located must be free of obstructions
and fixtures with sharp edges to prevent injury in the event that a user trips or loses balance and
falls.
Use the checklist below to ensure the proper installation of the E Series Upright Bike:
1.All parts and hardware in the package are accounted for.
2.All screws are tightened down to their specified values.
3.Upper neck is properly mounted and secured to the lower neck.
4.Left and right pedals are properly mounted and secured.
5.All cables and harnesses are properly plugged into their respective connectors.
6.The front and back display plastics are properly installed and secured.
7.Unit is leveled to the floor.
8.Once powered up, all features of the unit function properly.
9.Using a chest strap or wireless heart rate simulator, verify heart rate is recording properly.
For technical assistance call Star Trac Customer Service: 1 800 503 1221

24 620-7922 Rev B
E-UBe Upright Bike
(E-UBe/RBe) EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS
E-RBe Recumbent Bike

25 620-7922 Rev B
Step 1.
Remove all contents from the packaging and
verify that you have the following parts:
1. (1) Embedded display console.
2. (1) Operation manual.
3. (1) Hardware kit.
4. (1) Power adaptor (60W AC).
5. (1) Power cord.
Step 3.
Be careful with the display and place it face
down on top of a non-scratching surface to
protect it from being damaged.
Step 4.
Remove the back cover from the embedded dis-
play assembly and place it in a safe place for
later use.
(E-UBe/RBe) EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS
Step 2.
Verify the tool kit has the following parts:
1 2 3
4
5
1
2 3
Item Description QTY
1 Assembly instructions 1
2 Screw, Phillips Head, M4 x 19mm 18
3 Washer, flat, M4 5

26 620-7922 Rev B
Step 5.
Disconnect the ground cable from the ground
quick disconnect tab on the embedded display.
Save the cable for later use.
Step 6.
Mount the back cover to the display mounting
bracket using four (4) M4 x 0.7 x 19mm long
Phillips head screws and four (4) M4 flat wash-
ers.
Step 7.
Attach the ground cable to upper left screw on
the mounting bracket and secure tightly.
Step 8.
Pullout the coax adapter from the tuner card on
the embedded display.

27 620-7922 Rev B
Step 9.
Now screw in the coax adaptor to the coax ca-
ble coming out of the base neck.
Step 10.
Take the embedded display assembly to the
base unit. Hold the front display plastics at the
top with one hand while connecting the cables
and harnesses with the other.
Step 11.
Identify the four cables coming out of the neck
and mounting bracket:
1. Heart rate cable
2. Main I/O cable
3. Coax cable
4. DC power cable
1
2
3
4
Step 12.
Plug-in the heart rate cable from the neck into
the heart rate board connector on the FitCPU
board of the embedded display assembly.

28 620-7922 Rev B
Step 14.
Next plug in the coax cable into the coax
adapter on the tuner card of the embedded dis-
play assembly.
Step 15.
Now plug in the DC power cable from the base
neck into DC connectors on the embedded dis-
play assembly.
Step 13.
Plug-in the 12-pin main I/O cable from the neck
into the 12 pin connector on the FitCPU board of
the embedded display assembly.
Step 16.
Plug in the Heart rate ground cable into the
quick disconnect tab on the display mount.

29 620-7922 Rev B
Step 18.
Assemble the front and back display parts to-
gether by sliding the bottom of the front display
under the 2 tabs at the base first, then pressing
front display against the back cover.
Next, secure the front display to the back with
(8) M4 Phillips head screws.
Step 19.
Connect the in-house entertainment cable to the
RF input at the base of the unit.
Next, take the power supply from the kit and plug
it into the DC input. Then take the power adapter
cable from the kit and plug it into the power sup-
ply and the electrical receptacle.
Step 17.
Plug in the ground cable coming from upper left
side of the display mounting bracket into the
quick disconnect tab on the embedded display
assembly.
Step 20.
Turn power on. Perform a visual inspection, and
test the features and functions of the unit prior
to use.
Note: Refer to the User’s Manual for other settings
and instructions.
YOU HAVE NOW COMPLETED THE EMBEDDED DISPLAY INSTALLATION
1
2

30 620-7922 Rev B
ATTENTION
• Star Trac recommends that the bikes be spaced a minimum of 20.0 inches (0.5 m) apart to allow
safe and easy ingress and egress. Even more importantly, there must be at least 48 inches
(1.25 m) of free space behind the bike.
• As with any motorized equipment, the area where bikes are located must be free of obstructions
and fixtures with sharp edges to prevent injury in the event that a user trips or loses balance and
falls.
Use the checklist below to ensure the proper installation of the Embedded display:
1. All parts, tools and hardware in the package are accounted for.
2. Embedded display assembly is clear of any scratches or damage.
3. All screws are tightened down to their specified values.
4. Display’s mounting bracket and back cover are properly mounted and secured.
5. All cables and harnesses are properly plugged into their respective connectors.
6. The front and back display plastics are properly installed and secured.
7. Cable feed and power adaptor are plugged into the front base of the unit.
8. Unit is leveled to the floor.
9.Touch screen responds to commands as specified in the User’s Manual section regard-
ing the Calibration and Setup.
10. iPod® menu is functioning and user can browse and listen to music and videos.
11. TV is setup properly per the owner’s manual, signal is clear and audio is coming from
both earphones.
For technical assistance call Star Trac Customer Service: 1 800 503 1221

31 620-7922 Rev B
THIS PAGE INTENTIONALLY LEFT BLANK

32 620-7922 Rev B
(E-UB/RB) iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS
E-UB Upright Bike E-RB Recumbent Bike

33 620-7922 Rev B
Step 1.
Remove all contents from the packaging and
verify that you have the following parts:
1. (1) iPod® center console.
2. (1) iPod® cradle.
3. (1) Owner’s manual.
4. (1) Cable kit.
5. (1) Lower back cover.
Note: If the center console is being installed on a
new unit, then perform this installation prior to
mounting the display assembly onto the frame.
Step 3.
Using a #2 Phillips screwdriver, remove the (8)
screws on the back of the display plastic. Set
the screws aside, you will need them for re-
assembly.
Step 4.
Carefully open the display plastic, so as to not
detach the inner cables from the display.
(E-UB/RB) iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS
Step 2.
Verify the cable kit has the following two parts:
1. (1) Center console power cable.
2. (1) Headphone jack and mount.
1
2
3
4
5 1 2