Star Trac Pro Bike 6000 Series User manual

Pro Bike 6000 Series
Service Manual
March 20, 2006

Table of Contents – Pro Bike (6000 Series)
Created: 06/28/2004 •Preliminary Service Manual
Pro Bike (6000 Series) Service Manual
Table of Contents
1. Preventative Maintenance
2. Display Settings
3. Diagnostic Lights
4. Parts & Diagrams
This is a Preliminary Service Manual. Additional volumes will follow
as they become available.

Preventive Maintenance –Pro Bike (6000 Series)
Created: 06/28/2004 •Preliminary Service Manual
1.1
Pro Bike (6000 Series) Service Manual
Preventive Maintenance
Do not spray directly on
the display or heart rate
grips.
Spray on cloth first.
Check screws
Tighten pedals
To keep yourbike in top condition, Star Trac strongly recommends
performing regular daily, weekly and monthly preventive
maintenance routines outlined below.
Daily Maintenance
•Remove excessive accumulations of dust, dirt and other
substances by using a clean, soft cloth and a non-abrasive
liquid cleaner, such as Formula 409™or FANTASTIK™.
Wipe down the exterior of the display panel, handle bars,
seat, pedals, shrouds and heart rate grips.
Note: DO NOT spray the cleaner directly onto the display panel or
heart rate grips.
Weekly Maintenance
Perform the following services each week:
•Vacuum the floor under and around the bike. Move the bike
to another spot, if necessary, to vacuum thoroughly.
•Inspect the screws (i.e. display panel mounting screws)for
security, and retighten if necessary.
•Inspect the displaypanel keypads for wear.
Monthly Maintenance
Perform the following services each month, or as needed:
•Check that the seat, pedals and shroud are secure.
•Tighten the pedals onto their respective pedal cranks using
a 5/8-inch (15mm) open end wrench.

Settings –Pro Bike (6000 Series)
Created: 06/28/2004 •Preliminary Service Manual
2.1
Pro Bike (6000 Series) Service Manual
Settings –Manager Mode
The following keys are
used to modify
Manager Settings:
Upper and Lower Data
Information Window
SCROLL keys: Display
the next and previous
settings.
Increase and Decrease
Level Keys: Adjust the
value of the displayed
setting up and down
respectively, in
increments of 1 unit.
OK Key: Updates
(saves) the value of the
display setting in the
Flash memory, and
exits Manager Mode.
The Manager Mode allows you to query and modify the basic
settings of the bike.
Engaging Manager Mode
1.Press and hold the ,and keys together.
2.A beep will sound and the “MANAGER SETTINGS” will
display momentarily in the information window.
3.Release all keys. “SERIAL NUMBER” will display in the
information window.
The items that you may display and change:
Default values set in ()
Serial Number –Pro Bike serial number (0)
Date –Manufactures date for the Pro Bike (07/03)
Display Vers 1 –Display software version (N/A)
Display Vers 2 –Display software version (N/A)
LCB Vers –LCB software version (N/A)
Units –English = units of pounds, miles, feet inches; (English)
Metric = units of kilograms, kilometers, centimeters.
Time –Maximum time in minutes allowed for program, excluding
warm-up and cool-down (20)
Weight–Default (to user), typical weight in lb (UNITS=English) or
kg (UNITS = Metric) (155 lbs, 70 KG)
Language –Language is English, Dutch, French, German,
Spanish, Swedish, Italian or Katakana (English)

Settings –Pro Bike (6000 Series)
Created: 06/28/04 •Preliminary Service Manual
2.2
Pro Bike (6000 Series) Service Manual
Settings –Maintenance Mode
The following keys are
used to modify
Maintenance Settings:
Upper and Lower Data
Information Window
SCROLL keys: Display
the next and previous
settings.
Increase and Decrease
Level Keys: Adjust the
value of the displayed
setting up and down
respectively, in
increments of 1 unit.
OK Key: Updates
(saves) the value of the
display setting in the
Flash memory, and
exits Maintenance
Mode.
The Maintenance Mode allows you to query and modify the basic
settings of the bike.
Engaging Maintenance Mode
1.Press and hold the ,and keys together.
2.A beep will sound and the “MAINTENANCE SETTINGS” will
display momentarily in the information window.
3.Release all keys. “SERIAL NUMBER” will display in the
information window.
The items that you may display and change:
Default values set in ()
Serial Number –Pro Bike serial number (0)
Date –Manufactures date for the Pro Bike (07/03)
Display Vers 1 –Display software version (N/A)
Display Vers 2 –Display software version (N/A)
LCB Vers –LCB software version (N/A)
Units –English = units of pounds, miles, feet inches; (English)
Metric = units of kilograms, kilometers, centimeters.
Time –Maximum time in minutes allowed for program, excluding
warm-up and cool-down (20)
Weight–Default (to user), typical weight in lb (UNITS=English) or
kg (UNITS = Metric) (155 lbs, 70 KG)
Language –Language is English, Dutch, French, German,
Spanish, Swedish, Italian or Katakana (English)
Model–PB-UB = Pro Bike Upright
PB-RB = Pro Bike Recumbent
Nat Runner = Natural Runner (PB-UB)
OPER Hours –Total operating hours (0)
BATT Hours –Total battery use hours (0)
Quick Start –Number of times the Quick Start program was run
since last reset (0)
Manual–Number of times the Manual program was run since last
reset (0)
Warm Up –Number of times the Warm Up program was run since
the last reset (0)