Star Ultra Max 724T Owner's manual

MODELS 760T- & 772T-
Not approved for Canada
ANSI/NSF 4
®
®
®
®
®
ELECTRIC
GRIDDLES
MODELS
724T, 736T, 748T, 760T, 772T
CHROME MODELS
724TCHS, 736TCHS, 748TCHS, 760TCHS, 772TCHS
Installation and
Operation
Instructions
2M-Z8514 REV G (05-22)
724T

2
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not
responsible for errors or omissions in information provided or conclusions
provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it
ready when you call to ensure a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:
Telephone: [phone]
Fax: [phone]
E-mail [email protected]
Website: www.star-mfg.com
Service Help Desk
Authorized Service Agent Listing
Reference the listing provided with the unit
or
for an updated listing go to:
Website: www.star-mfg.com
E-mail [email protected]
Mailing Address: Star Manufacturing International Inc.
265 Hobson Street
Smithville, TN 37166
U.S.A

3
2M-Z8514, Ultra-Max Electric Griddle
This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations. For equipment to be used by the general public, please
contact the factory.
INSTALLATION
The griddles are equipped for the voltage indicated on the nameplate mounted on the front
panel. They will operate on alternating current (AC) only.
DO NOT CONNECT TO DIRECT CURRENT (DC).
The installation of the electric griddle should conform to the:
NATIONAL ELECTRIC CODE AND ALL LOCAL ELECTRIC CODES AND
ORDINANCES AND THE LOCAL ELECTRIC COMPANY RULES AND
REGULATIONS
For your protection we recommend that a qualied electrician install this griddle. He should be
familiar with electrical installations and all electric codes. Proper connections and power supply are
essential for efcient performance. The external wiring should be in conduit or an approved type
of exible cable suitable for operation at the temperature indicated on the wiring diagram, and of a
proper size to carry the load. The supply circuit should be properly fused and equipped with a means
of disconnecting, as required by local electrical code. THE BODY OF THE GRIDDLE SHOULD BE
GROUNDED (DO NOT GROUND TO A GAS SUPPLY LINE).
GENERAL OPERATING PROCEDURES
The Ultra-Max series electric griddles may be wired for operation in the eld for either 1-phase or
3-phase power supplies by making line connections at the junction box(es) located at the rear of the
unit. Models 724T-230/400V, 736T-230/400V & 748T-230/400V, should be wired for 3-phase power
supply only. Two junction boxes are provided on the 760T & 772T for making line connections.
CONNECTING POWER SUPPLY
Detach cover on junction box at rear of unit. There is a terminal block for the supply connection in the
junction box. Wires can be rerouted in the terminal block for 3phase hook-up. See wiring diagrams
and model voltage on unit panel
LOCATING AND LEVELING THE UNIT
Do not install the unit closer than 1-inch from a side wall and/or closer than 1-inch from a rear wall.
Make sure the unit is properly ventilated. Level unit by adjusting the (4) feet which have an adjustment
of 1-3/4” (43.75mm) for accurate leveling and perfect line-up with other Ultra-Max series units. After the
griddle is in its nal position, adjust the legs to create 1/8 inch slant from back to front. This will allow
the grease to run into the grease gutter and provide proper heating for the elements.
SEASONING THE GRIDDLE HEATING SURFACE
Before initial use, clean the griddle surface thoroughly with hot soap and water. See Griddle care on
page 4 for further information. After the griddle has been thoroughly cleaned, it should be seasoned
to prevent food from sticking. Before using and after each thorough scouring, season the griddle
heating surface in the following manner.
1. Remove any shipping material from the cooking surface and thouroughly clean the entire grill
with hot soap and water.
2. Turn temperature control dials to 350°F (177°C).
3. Using a clean cloth, not a spatula, brush a thin lm of cooking oil over the griddle cooking surface.
This lm should remain on the hot griddle surface for half an hour.
4. Remove the excess oil and wipe clean.
5. Apply another lm of cooking oil over the hot cooking area for another half hour and again
remove excess oil and wipe clean. The griddle surface should now be ready for use.
Even with careful seasoning, food may, to some extent, stick to the griddle cooking surface until the
griddle plate is broken in.
CAUTION
WARNING

4
2M-Z8514, Ultra-Max Electric Griddle
TEMPERATURE CONTROL
The temperature controls are combination “ON/OFF” switches and thermostats. Turning the dial knob
automatically maintains the selected heat range.
The Ultra-Max electric griddle line has one thermostat for every 12” (30cm) section of griddle that
operates independently of one another. Each thermostat controls the section of the griddle above it
and may be set at different temperatures as desired.
COOKING
Set the thermostat dial knob at the temperature desired. After a short pre-heating period, the
thermostat will automatically maintain the selected temperature.
IDLING
During idle periods, to save on operating costs, lower the temperature setting of the thermostat to
about 250°F (121°C). It is not necessary to maintain cooking temperature during idle periods, as the
griddle can quickly be reheated to the desired temperature.
SIGNAL LIGHTS
Each thermostat has its own signal light which indicates when the unit’s control knob is in the on
position. Cooking surface will be hot when the control knob is in this position.
GRIDDLE CARE (NON-CHOME SURFACES)
It takes very little time and effort to keep the griddle attractive and performing at top efciency.
If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard
substance which is extremely difcult to remove. To prevent this condition, the following suggestions
for cleanliness should be followed:
1. After each use, scrape the griddle with a scraper or exible spatula to remove excess grease
and food. A waste drawer is provided for the drippings. If there is an accumulation of burned
on grease and food, the griddle should be thoroughly scoured and re-seasoned. Use pumice
or griddle stone while the griddle is warm. Do not use steel wool because of the danger of steel
slivers getting into the food.
2. Daily, use a clean cloth and a good non-abrasive cleaner to clean the stainless steel body of
the griddle. Wipe the polished front with a soft cloth.
3. At least once a day, remove the waste drawer and wash in the same way as an ordinary cooking
utensil. The drawers are removed by pulling forward until they are released from their track.
GRIDDLE CARE (CHROME SURFACES)
(Chrome surface griddles are marked with “CHS” at the end of the model number designation on the
nameplate.) It takes very little time and effort to keep this Industrial Chrome griddle surface sparkling
clean and performing at top efciency. DO NOT allow grease to accumulate as it will carbonize and
become difcult to remove. To prevent this condition, the following cleaning suggestions should be
followed:
1. Remove excess oil and food regularly with a 4” (100mm) wide razor sharp type scraper and
wipe surface with a damp cloth if desired.
2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated, non-
abrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed
by wiping with clean wet cloth.
3. Follow steps 2 and 3 from Griddle Care (Non-Chrome Surfaces).
ON CROME SURFACES:
1. Never use pumice, griddle stones, or abrasives on the surface.
2. Never strike the griddle surface with a sharp instrument or spatula edge.
3. Never use steel wool.
4. Never use commercial liquid grill cleaner on the griddle surface.
5. Abusing the surface voids the warranty.
CAUTION

5
2M-Z8514, Ultra-Max Electric Griddle
GREASE DRAWER
A grease drawer is located at the front can be removed for cleaning by pulling drawer forward. This
drawer contains hot grease and should be checked and emptied when necessary or at least once a
day.
EXERCISE EXTREME CARE IN HANDLING THE GREASE DRAWER
CONTAINING HOT GREASE.
Never pour large amounts of water onto a hot griddle surface, the sudden
temperature change generated by the steam can cause the surface to warp
and possibly the thermal sensors in your ansul hood system to dischage.
Instead follow the cleaning procedures in this manual.
MAINTENANCE AND REPAIRS
Contact the factory, a service representative, or a local service company for service or required
maintenance.
CAUTION
CAUTION

LIMITED EQUIPMENT WARRANTY
Star Manufacturing [as well as its subsidiaries] warrants to the original purchaser
of new Star products to be free from defects in material or workmanship, under
normal and proper use and maintenance service as specified by Star and upon
proper installation and start-up in accordance with the instructions supplied with
each Star unit. Star’s obligation under this warranty is limited to a period of one [1]
year from the date of original installation, or eighteen [18] months from original
invoice date, whichever occurs first. Defects that occur as a result of normal use,
within the time period and limitations defined in this warranty, will at Star’s
discretion have the parts replaced or repaired by Star or a Star-authorized service
agency.
THIS WARRANTY IS SUBJECT TO ALL LISTED CONDITIONS
Repairs performed under this warranty are to be performed by a Star authorized
service agency. Star will not be responsible for charges incurred or service
performed by non-authorized repair agencies. In all cases, the nearest Star-
authorized service agency must be used. Star will be responsible for normal labor
charges incurred in the repair or replacement of a warrantied product within 50
miles (80.5 km) of an authorized service agency. Time and expense charges for
anything beyond that distance will be the responsibility of the owner. All labor will
need to be performed during regular service hours. Any overtime premium will be
charged to the owner. For all shipments outside the U.S.A. and Canada, please see
the International Warranty for specific details. It is the responsibility of the owner
to inspect and report any shipping damage claims, hidden or otherwise, promptly
following delivery. No mileage or travel charges will be honored on any equipment
that is deemed portable. In general, equipment with a cord and plug weighing less
than 50 lb. (22.7 kg) is considered portable and should be taken or shipped to the
closest authorized service agency, transportation prepaid.
CONTACT
Should you require any assistance regarding the operation or maintenance of any
Star Manufacturing; phone, email or fax our service department. In all
correspondence provide the model number and serial number of the unit needing
service; include the voltage or gas type.
Normal Business Hours: 8:00 a.m. to 4:30 p.m. Central
Telephone: [phone] Tech Service Option 2
Email: [e-mail]
www.Star-Mfg.com
January 29, 2021
WARRANTY EXCLUSIONS
THE FOLLOWING WILL NOT BE COVERED UNDER WARRANTY.
Star’s sole obligation under this warranty is limited to either repair or
replacement parts, subject to the additional limitations detailed below. This
warranty neither assumes nor authorizes any person to assume obligations
other than those expressly covered by this warranty.
• Any product which has not been used, maintained, or installed in
accordance with the directions published in the appropriate installation sheet
and/or owner’s manual, including incorrect gas or electrical connection. Star
is not liable for any unit which has been mishandled, abused, misapplied,
subjected to harsh chemicals, modified by unauthorized personnel, damaged
by flood, fire, or other acts of nature [or God], or which have an altered or
missing serial number.
• Installation, labor, and job checkouts, calibration of heat controls, air and
gas burner/bypass/pilot adjustments, gas or electrical system checks, voltage
and phase conversions, cleaning of equipment, or seasoning of griddle
surface.
• Replacement of fuses or resetting of circuit breakers, safety controls, or
reset buttons.
• Replacement of broken or damaged glass components, quartz heating
elements, and light bulbs.
• Labor charges for all removable and consumable parts in gas charbroilers
and hotplates, including but not limited to burners, grates, and radiants.
• Any labor charges incurred by delays, waiting time, or operating restrictions
that hinder a service technician’s ability to perform service.
• Replacement of parts that fail or are damaged due to normal wear or labor
for replacement of parts that can be replaced during a daily cleaning routine,
such as but not limited to silicone belts, PTFE non-stick sheets, control labels,
knobs, bulbs, fuses, quartz heating elements, baskets, racks, and grease
drawers.
• Any economic loss of business or profits.
• Non-OEM parts. Use of non-OEM parts without Star’s approval will void the
warranty.
• Units exceeding one [1] year from original installation date, or more than
eighteen [18] months from original purchase date, whichever comes first.
ADDITIONAL WARRANTIES
• Specific/chain-specific equipment may have additional and/or extended
warranties.
PRODUCTS
PARTS
LABOR
Star Ultra Max Ⓡfryers, griddles,
charbroilers and hotplates
2 years
2 years
Star Max Ⓡfryers, griddles,
charbroilers and hotplates
2 years
2 years
Staltekroller grill coatings
5 years
Cast iron grates, burners
and burner shields
1 year
Original Star, Toastmaster or Holman
parts sold to repair equipment
90 days
The foregoing warranty is in lieu of any, and all other warranes expressed
or implied and constutes the enre warranty.

7
3
1
4
2
TO CONVERT TO 3 PHASE
MOVE WIRES #2 AND #3 TO
THE 3RD OPEN TERMINAL
CONNECTOR Z SHOWN.
FOR SUPPLY CONNECTION USE
COPPER WIRE ONLY, SUITABLE FOR
AT LEAST 90°C (194°F). USE GAUGE
SHOWN OR LARGER.
NOMINAL AMPS PER LINE 3 PH.
208V-3 PHASE
X
55.3
Y Z
240V-3 PHASE
X Y Z
48
36.255.3 48 31.4
208V 240V
17.4 KW
SINGLE PHASE
83.6 72.5
#3
AWG
#3
AWG
X-Y X-Y
5
6
8
7
2,3
4,6,8
1,5,7
2M-Z8447
AWG
#6
AWG
#6
AWG
#8
AWG
#6
AWG
#6
AWG
#8
X
Y
TERMINAL BLOCK
1 PHASE FIELD WIRING
GROUND WIRE
1,3,5,7
2,4,6,8
17.4 KW 17.4 KW 17.4 KW
X
Y
Z
TERMINAL BLOCK
3 PHASE FIELD WIRING
GROUND CONNECTOR
GROUND WIRE
PILOT LIGHT
THERMOSTAT
HEATING ELEMENT
MODEL 748T
MODEL 736T, 760T (1 SIDE), 772T (BOTH SIDES EACH)
MODEL 724T AND 760T (1SIDE)
3
1
4
2
TO CONVERT TO 3 PHASE
MOVE WIRE #3 TO
THE 3RD OPEN TERMINAL
CONNECTOR Z SHOWN.
FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT
LEAST 90°C (194°F). USE GAUGE SHOWN OR LARGER.
NOMINAL AMPS PER LINE 3 PH.
208V-3 PHASE
X
20.9
Y Z
240V-3PHASE
X Y Z
18.1
20.936.2 31.3 18.1
208V 240V
8.7 KW
SINGLE PHASE
41.8 36.3
#6
AWG #8 AWG
X-Y X-Y
#12
AWG
#8
AWG
#12
AWG
#12
AWG
#8
AWG
#12
AWG
2M-Z8445
1
2,4
3
TERMINAL BLOCK
SINGLE PHASE
FIELD WIRING
GROUND WIRE
1,3
2,4
8.7 KW 8.7 KW 8.7 KW
X
TERMINAL BLOCK
3 PHASE
FIELD WIRING
GROUND WIRE
Y
Z
PILOT
LIGHT
HEATING ELEMENT
THERMOSTAT
3
1
6
5
4
2
TO CONVERT TO 3 PHASE
MOVE WIRES #4 AND #5 TO
THE 3RD OPEN TERMINAL
CONNECTOR Z SHOWN.
NOTE:
1) FOR SUPPLY CONNECTIONS
USE COPPER WIRE ONLY,
SUITABLE FOR AT LEAST 90°C
(194°F). USE GAUGE SHOWN OR
LARGER.
NOMINAL AMPS PER LINE 3 PH.
208V-3 PHASE
X
36.2
Y Z
36.236.2
240V-3PHASE
X Y Z
31.4 31.4 31.4
208V 240V
13.05 KW
SINGLE PHASE SUPPLY
62.7 54.4
#8AWG #8AWG#4AWG #6AWG
X-Y X-Y
2M-Z8446
1,3
2,6
4,5
X
Y
TERMINAL BLOCK
SINGLE PHASE
FIELD WIRING
GROUND WIRE
1,3,5
2,4,6
13.05 KW 13.05 KW 13.05 KW
X
Y
Z
TERMINAL BLOCK
3 PHASE
FIELD WIRING
GROUND CONNECTOR
GROUND WIRE
THERMOSTAT
HEATING ELEMENT
PILOT
LIGHT
NOTE: Wattage is 4.35 kw
per heated zone. See unit
nameplate on front panel
for correct supply voltage.

8
MODEL 724T 230V 3 PHASE
MODEL 748T 230V 3 PHASE
MODEL 736T 230V 3 PHASE
X
TERMINAL BLOCK
FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT LEAST 90°C (194°F).
USE #12 AWG OR LARGER. DO NOT CONNECT TO A SYSTEM OPERATING AT MORE THAN 250
VOLTS TO GROUND
230/400 VOLT Y - 8.7 KW
XYZ
2M-Z8449 REV B 7-15-08
12.6 12.6
6
5
43
21
Y
Z
15
14
15
14
12.6
NOM. AMPS
PER LINE
N
16 16 16 16 16 16
17
13 13
CONTACTOR
HEATING
ELEMENT
N
THERMOSTAT
PILOT
LIGHT
G
G
X
TERMINAL BLOCK
FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT LEAST 90°C (194°F).
USE #10 AWG OR LARGER. DO NOT CONNECT TO A SYSTEM OPERATING AT MORE THAN 250
VOLTS TO GROUND
230/400 VOLT Y - 13.05 KW
XYZ
2M-Z8552 REV B 7-15-08
18.9 18.9
9
876
5
43
21
Y
Z
15
14
15
14
15
14
18.9
NOM. AMPS
PER LINE
N
16 16 16 16 16 16 16 16 16
17 17
13 13 13
CONTACTOR
HEATING
ELEMENT
THERMOSTAT
N
PILOT LIGHT
G
G
X
TERMINAL BLOCK
FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR AT LEAST 90°C (194°F).
USE #8 AWG OR LARGER. DO NOT CONNECT TO A SYSTEM OPERATING AT MORE THAN 250
VOLTS TO GROUND
230/400 VOLT Y - 17.4 KW
XYZ
2M-Z8450 REV B 7-15-08
25.2 25.2
16 16 16
15
14
10
12 9
876
5
43
21
Y
Z
15
14
15
14
15
14
25.2
NOM. AMPS
PER LINE
N
16 16 16 16 16 16 16 16 16
11
1717 17
13 13 13 13
CONTACTOR
HEATING
ELEMENT
THERMOSTAT
N
PILOT
LIGHT
G
G
NOTE: Wattage is 4.35
kw per heated zone.
(1450 watts per-element)
See unit
nameplate for correct
supply voltage.

9
X
FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY, SUITABLE FOR
AT LEAST 90°C (194°F). USE #8 AWG OR LARGER. DO NOT CONNECT
TO A SYSTEM OPERATING AT MORE THAN 250 VOLTS TO GROUND
760T 230/400 VOLT Y - 21.75 KW
XYZ
31.5 31.5
16 16 16
15
14
10
12
7
5
43
21
Y
Z
15
14
15
14
15
14
31.5
NOM. AMPS
PER LINE
N
16 16 16 16 16 16 16 16 16
11
1717 17
13 13 13 13
N
G
G
16 16 16
15
14
7
17
13
16 16 16
15
14
13
A
B
C
D
LEGEND
A HEATING ELEMENT
B CONTACTOR
C PILOT LIGHT
D THERMOSTAT
E TERMINAL BLOCK E
9
8
6
9
8
2M-Z11776
MODEL 760T 230/400V Y 3 PHASE

10
2M-Z8514, Ultra-Max Electric Griddle
6
3
1
2
10
9
8
4
5
7
15 13
14
NAMEPLATE
17
16 12 11
22
19 20
21
26
23
24
25
27
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
MODEL 724T, 736T, 748T, 760T, 772T
STAR MANUFACTURING INTERNATIONAL, INC.
SK2122 REV. -- 02/21/2005

11
2M-Z8514, Ultra-Max Electric Griddle
PARTS LIST July 17, 2008, Rev. E
724T Ultra-Max Electric Griddles
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Per
Unit Description and Model Designation
Part
Number
Key
Number
1 G5-Z8491 1 REAR PANEL 724T
2 G5-824023 1 JUNCTION BOX ASSY. 724T
G5-Z10348 1 ELECTRICAL BOX 724T-230V
3 G5-Z8481 1 JUNCTION BOX COVER 724T
G5-Z10349 1 ELECTRICAL BOX COVER 724T-230V
4 2E-Z8482 1 TERMINAL BLOCK 724T
2E-Z9565 1 TERMINAL BLOCK 5 POS. 724T-230V
5 2E-Z8423 1 GROUND LUG 724T
6 G5-824020 1 GRIDDLE PLATE ASSY. 724T
6 G5-824024 1 GRIDDLE PLATE ASSY. CHROME 724T
7 G5-824021 1 BODY ASSY. 724T
8 2E-Z8358 1 3/4” EMT CONNECTOR 724T
9 2E-Z8361 1 3/4” EMT TUBE - 22 3/4” L. 724T
10 2E-Z8356 1 3/4” PLASTIC BUSHING 724T
11 G5-824022 1 FRONT PANEL ASSY. 724T
12 2M-Z8473 1 FRONT PANEL OVERLAY 724T
13 2P-Z8478 2 HINGE ALL MODELS ALL
14 2E-30700-03 2 3 POLE CONTACTOR 724T - 230V ONLY
15 2T-Z5958 2 THERMOSTAT 724T
16 2J-Y6690 2 PILOT LIGHT 724T
17 2R-Z8490 2 KNOB 724T
19 2N-Z8484 2 HEATER ELEMENT 4350 W 208V 724T (208V MODELS)
19 2N-Z8485 2 HEATER ELEMENT 4350 W 240V 724T (240V MODELS)
20 2N-Z8487 6 HEATER ELEMENT 1450 W 230V 724T (230V MODELS)
21 G5-Z8489 12 HEATER ELEMENT CLAMP 724T
22 G5-Z8488 2 HEATER ELEMENT SHIELD 724T
23 G5-824012 1 CHUTE ASSY. 724T
24 G5-Z8515 1 DRAWER SLIDE 724T
25 G5-824014 1 GREASE DRAWER ASSY. 724T
26 G5-Z8468 2 BOTTOM PANEL 724T
27 2A-Z4614 4 FOOT ALL MODELS ALL
MODEL
Star Manufacturing International, Inc.

12
2M-Z8514, Ultra-Max Electric Griddle
PARTS LIST July 17, 2008, Rev. E
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Per
Unit Description and Model Designation
Part
Number
Key
Number
MODEL
1 G5-Z8492 1 REAR PANEL 736T
2 G5-824023 1 JUNCTION BOX ASSY. 736T
G5-Z10348 1 ELECTRICAL BOX 736T-230V
3 G5-Z8481 1 JUNCTION BOX COVER 736T
G5-Z10349 1 ELECTRICAL BOX COVER 736T-230V
4 2E-Z8482 1 TERMINAL BLOCK 736T
2E-Z9565 1 TERMINAL BLOCK 5 POS 736T-230V
5 2E-Z8423 1 GROUND LUG 736T
6 G5-836018 1 GRIDDLE PLATE ASSY. 736T
6 G5-836021 1 GRIDDLE PLATE ASSY. CHROME 736T
7 G5-836019 1 BODY ASSY. 736T
8 2E-Z8358 1 3/4” EMT CONNECTOR 736T
9 2E-Z8361 1 3/4” EMT TUBE - 22 3/4” L. 736T
10 2E-Z8356 1 3/4” PLASTIC BUSHING 736T
11 G5-836020 1 FRONT PANEL ASSY. 736T
12 2M-Z8474 1 FRONT PANEL OVERLAY 736T
13 2P-Z8478 2 HINGE ALL MODELS ALL
14 2E-30700-03 3 3 POLE CONTACTOR 736T - 230V ONLY
15 2T-Z5958 3 THERMOSTAT 736T
16 2J-Y6690 3 PILOT LIGHT 736T
17 2R-Z8490 3 KNOB 736T
19 2N-Z8484 3 HEATER ELEMENT 4350 W 208V 736T (208V MODELS)
19 2N-Z8485 3 HEATER ELEMENT 4350 W 240V 736T (240V MODELS)
20 2N-Z8487 9 HEATER ELEMENT 1450 W 230V 736T (230V MODELS)
21 G5-Z8489 18 HEATER ELEMENT CLAMP 736T
22 G5-Z8488 3 HEATER ELEMENT SHIELD 736T
23 G5-824012 1 CHUTE ASSY. 736T
24 G5-Z8515 1 DRAWER SLIDE 736T
25 G5-824014 1 GREASE DRAWER ASSY. 736T
26 G5-Z8468 1 BOTTOM PANEL 736T
26 G5-Z8469 1 BOTTOM PANEL 736T
27 2A-Z4614 4 FOOT ALL MODELS ALL
736T Ultra-Max Electric Griddles
Star Manufacturing International, Inc.

13
2M-Z8514, Ultra-Max Electric Griddle
PARTS LIST July 17, 2008, Rev. E
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Per
Unit Description and Model Designation
Part
Number
Key
Number
MODEL
748T Ultra-Max Electric Griddles
Star Manufacturing International, Inc.
1 G5-Z8493 1 REAR PANEL 748T
2 G5-824023 1 JUNCTION BOX ASSY. 748T
G5-Z10348 1 ELECTRICAL BOX 748T-230V
3 G5-Z8481 1 JUNCTION BOX COVER 748T
G5-Z10349 1 ELECTRICAL BOX COVER 748T-230V
4 2E-Z8482 1 TERMINAL BLOCK 748T
2E-Z9565 1 TERMINAL BLOCK 5 POS 748T-230V
5 2E-Z8423 1 GROUND LUG 748T
6 G5-848018 1 GRIDDLE PLATE ASSY. 748T
6 G5-848021 1 GRIDDLE PLATE ASSY. CHROME 748T
7 G5-848019 1 BODY ASSY. 748T
8 2E-Z8358 1 3/4” EMT CONNECTOR 748T
9 2E-Z8361 1 3/4” EMT TUBE - 22 3/4” L. 748T
10 2E-Z8356 1 3/4” PLASTIC BUSHING 748T
11 G5-848020 1 FRONT PANEL ASSY. 748T
12 2M-Z8475 1 FRONT PANEL OVERLAY 748T
13 2P-Z8478 2 HINGE ALL MODELS ALL
14 2E-30700-03 4 3 POLE CONTACTOR 748T - 230V ONLY
15 2T-Z5958 4 THERMOSTAT 748T
16 2J-Y6690 4 PILOT LIGHT 748T
17 2R-Z8490 4 KNOB 748T
19 2N-Z8484 4 HEATER ELEMENT 4350 W 208V 748T (208V MODELS)
19 2N-Z8485 4 HEATER ELEMENT 4350 W 240V 748T (240V MODELS)
20 2N-Z8487 12 HEATER ELEMENT 1450 W 230V 748T (230V MODELS)
21 G5-Z8489 24 HEATER ELEMENT CLAMP 748T
22 G5-Z8488 4 HEATER ELEMENT SHIELD 748T
23 G5-824012 1 CHUTE ASSY. 748T
24 G5-Z8515 1 DRAWER SLIDE 748T
25 G5-824014 1 GREASE DRAWER ASSY. 748T
26 G5-Z8468 1 BOTTOM PANEL 748T
26 G5-Z8470 1 BOTTOM PANEL 748T
27 2A-Z4614 4 FOOT ALL MODELS ALL

14
2M-Z8514, Ultra-Max Electric Griddle
PARTS LIST July 17, 2008, Rev. E
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Per
Unit Description and Model Designation
Part
Number
Key
Number
MODEL
760T Ultra-Max Electric Griddles
Star Manufacturing International, Inc.
1 G5-Z8494 1 REAR PANEL 760T
2 G5-824023 2 JUNCTION BOX ASSY. 760T
3 G5-Z8481 2 JUNCTION BOX COVER 760T
4 2E-Z8482 2 TERMINAL BLOCK 760T-208/240V
2E-Z9565 1 TERMINAL BLOCK 5 POS #4 760T-230V
5 2E-Z8423 2 GROUND LUG 760T
6 G5-860018 1 GRIDDLE PLATE ASSY. 760T
6 G5-860021 1 GRIDDLE PLATE ASSY. CHROME 760T
7 G5-860019 1 BODY ASSY. 760T
G5-860012 1 BODY ASSY 760T-230V
8 2E-Z8358 2 3/4” EMT CONNECTOR 760T
9 2E-Z8361 2 3/4” EMT TUBE - 22 3/4” L. 760T
10 2E-Z8356 2 3/4” PLASTIC BUSHING 760T
11 G5-860020 1 FRONT PANEL ASSY. 760T
12 2M-Z8476 1 FRONT PANEL OVERLAY 760T
13 2P-Z8478 2 HINGE ALL MODELS ALL
14 2E-30700-03 5 CONTACTOR, 3PH SP7.10-CO 760T-230V
15 2T-Z5958 5 THERMOSTAT 760T
16 2J-Y6690 5 PILOT LIGHT 760T
17 2R-Z8490 5 KNOB 760T
19 2N-Z8484 5 HEATING ELEMENT 4350 W 208V 760T (208V MODELS)
2N-Z8485 5 HEATING ELEMENT 4350 W 240V 760T (240V MODELS)
2N-Z8487 15 HEATING ELEMENT 1450W 230V 760T-230V
21 G5-Z8489 30 HEATER ELEMENT CLAMP 760T
22 G5-Z8488 5 HEATER ELEMENT SHIELD 760T
23 G5-824012 2 CHUTE ASSY. 760T
24 G5-Z8515 2 DRAWER SLIDE 760T
25 G5-824014 2 GREASE DRAWER ASSY. 760T
26 G5-Z8468 2 BOTTOM PANEL 760T
G5-Z8471 1 BOTTOM PANEL 760T
27 2A-Z4614 4 FOOT ALL MODELS ALL

15
2M-Z8514, Ultra-Max Electric Griddle
PARTS LIST July 17, 2008, Rev. E
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Per
Unit Description and Model Designation
Part
Number
Key
Number
MODEL
772T Ultra-Max Electric Griddles
Star Manufacturing International, Inc.
1 G5-Z8495 1 REAR PANEL 772T
2 G5-824023 2 JUNCTION BOX ASSY. 772T
3 G5-Z8481 2 JUNCTION BOX COVER 772T
4 2E-Z8482 2 TERMINAL BLOCK 772T
5 2E-Z8423 2 GROUND LUG 772T
6 G5-872018 1 GRIDDLE PLATE ASSY. 772T
6 G5-872021 1 GRIDDLE PLATE ASSY. CHROME 772T
7 G5-872019 1 BODY ASSY. 772T
8 2E-Z8358 2 3/4” EMT CONNECTOR 772T
9 2E-Z8361 2 3/4” EMT TUBE - 22 3/4” L. 772T
10 2E-Z8356 2 3/4” PLASTIC BUSHING 772T
11 G5-872020 1 FRONT PANEL ASSY. 772T
12 2M-Z8477 1 FRONT PANEL OVERLAY 772T
13 2P-Z8478 2 HINGE ALL MODELS ALL
15 2T-Z5958 6 THERMOSTAT 772T
16 2J-Y6690 6 PILOT LIGHT 772T
17 2R-Z8490 6 KNOB 772T
19 2N-Z8484 6 HEATER ELEMENT 4350 W 208V 772T (208V MODELS)
19 2N-Z8485 6 HEATER ELEMENT 4350 W 240V 772T (240V MODELS)
21 G5-Z8489 36 HEATER ELEMENT CLAMP 772T
22 G5-Z8488 6 HEATER ELEMENT SHIELD 772T
23 G5-824012 2 CHUTE ASSY. 772T
24 G5-Z8515 2 DRAWER SLIDE 772T
25 G5-824014 2 GREASE DRAWER ASSY. 772T
26 G5-Z8468 2 BOTTOM PANEL 772T
26 G5-Z8472 1 BOTTOM PANEL 772T
27 2A-Z4614 4 FOOT ALL MODELS ALL

STAR MANUFACTURING INTERNATIONAL INC.
Star - Holman - Lang - Wells - Toastmaster
265 HOBSON ST. SMITHVILLE, TN 37166
[phone]
www.star-mfg.com