StarTech.com DKT30CHVGPD User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Product Diagram (DKT30CHVGPD)
Front View:
Side View:
Port/Connection Function
1USB-A Port • Connect a USB Device to the Host
2RJ45 Port • Connect a Network Device to the Host
3VGA Port • Connect a VGA Video Display Device to the
Host
4HDMI Port • Connect an HDMI Video Display Device to
the Host
Note: The Multiport Adapter is a single
video display adapter. You can connect either
an HDMI Display or a VGA Display.
5USB-C Host
Connector
• Connect the Multiport Adapter to the Host
• Power Delivery 3.0 (charging/power)
USB-C Multiport Adapter | HDMI | VGA | PD
1
6USB-C Power Port • Connect a USB-C Power Adapter to the
Host Computer
• Power Delivery 3.0 (charging/power)
Requirements
For the latest requirements, please visit www.startech.com/DKT30CHVGPD.
Powering the Multiport Adapter
USB Power Delivery 3.0
Fast Role Swap:
A Fast Role Swap function is available when using Power Delivery 3.0. This function
prevents USB data disruption when switching power sources (bus power to USB-C
power adapter or USB-C power adapter to bus power). For this function to work, the
host laptop must also support Power Delivery 3.0.
Bus Power:
The Multiport Adapter is powered by the Host Computer’s USB-C Port and does not
require a separate power adapter.
1. Connect the USB-C Connector on the Multiport Adapter to a USB-C Port on the
Host Computer.
2. The Host Computer’s operating system will automatically detect and install the
required driver.
Note: Host Computers that have a USB-C port that supports a maximum of 4.5W of
Bus Power will only get RJ45 Port functionality. All other ports on the Multiport Adapter
will be disabled due to insucient Bus Power.
USB-C Power Adapter:
The Multiport Adapter is powered using the Host Computer’s USB-C Power
Adapter. The maximum power delivery input is 95W. The Multiport Adapter requires
10W of Power Delivery capacity to power the Multiport Adapter and its connected
devices leaving a maximum power delivery of 85W for laptop charging.
Note: The Multiport Adapter’s Maximum Power Delivery is based on the limitations
of the Host Computer’s USB-C Power Adapter.
1. Connect the Multiport Adapter’s USB-C Connector to a USB-C Port on the Host
Computer.
2. Connect the USB-C Connector on the Host Computer’s Power Adapter to the
USB-C Power Port on the Multiport Adapter. The Universal Adapter will power
the Multiport Adapter and pass power through to the Host Computer.
24
3
5
6

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0.5cm
between the radiator and your body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策•製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
2. Connect the other end of the HDMI Cable to an HDMI In Port on a Video Display
Device.
RJ45 Port
The RJ45 Port is used to connect the Multiport Adapter to a Network Device.
1. Connect a CAT5e/CAT6 Cable to the RJ45 Port on the Multiport Adapter.
2. Connect the other end of the CAT5e/CAT6 cable to an RJ45 Port on a compatible
Network Device.
VGA Port
The VGA Port is used to connect the Multiport Adapter to a Video Display Device.
1. Connect a VGA Cable to the VGA Port on the Multiport Adapter.
2. Connect the other end of the VGA Cable to the VGA Port on a Video Display
Device and tighten the two screws of either side on the VGA Connector.
3. Depending on the Host Computer’s operating system, the Multiport Adapter will
automatically detect and install the required driver.
Connecting the Multiport Adapter
USB-A Port
The USB-A Port can be used as a charging port (e.g. cell phone, laptop, tablet, etc.), or to
connect a USB storage device (e.g. ash drive) or a USB peripheral device (e.g. keyboard,
mouse, etc.).
If connecting a USB-A Device that has a cable (e.g. cell phone):
1. Connect the USB-A Device’s USB-A Cable to the USB-A Port on the Multiport
Adapter.
2. Connect the other end of the USB-A Cable to a USB Port on your USB Device.
If connecting a USB-A Device with no cable (e.g. ash drive):
• Connect the USB-A Device to the USB-A Port on the Multiport Adapter.
If connecting a USB-A Device that has a built-in cable (e.g. mouse):
• Connect the USB-A Device’s USB-A Cable to the USB-A Port on the Multiport
Adapter.
HDMI Port
The HDMI Port is used to connect the Multiport Adapter to a Video Display Device.
1. Connect an HDMI Cable to the HDMI Port on the Multiport Adapter.