StarTech.com ITB20D3250 User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: July 18, 2019 11:29 AM
Product Diagram (ITB20D3250)
Component Function
1Power Connector (side) • Used to power the Adapter.
2LED Indicator
• Solid: Indicates that the Adapter is powered
On.
• O: Indicates that the Adapter is not receiving
power.
3Terminal Block Wires
• Used to connect and power a Device.
• Red Wire = Positive
• Black Wire = Negative
• Output = 20V
• Current = 3.25A 65W
Requirements
For the latest requirements, please visit www.startech.com/ITB20D3250
• (Optional) Small Flat Head Screwdriver x 1
• Device with a Two or Three Conductor Terminal Block Connector x 1
Using the Two Conductor Terminal Block Connector
1. Remove the Two Conductor Terminal Block Connector from the Device, you want
to power.
2. Plug the Two Conductor Terminal Block Connector on the Adapter into the
Terminal Connector on the Device.
Note: Ensure the polarity of the input power is correctly matched with the Terminal
Block Pins to ensure proper functionality. Refer to the Device’s vendor manual for
further information on properly wiring the Device.
Universal 65W DC Power Adapter | 20V 3.25A | Industrial
Two Conductor Terminal Block Connector
Using the Three Conductor Terminal Block Connector
1. Using a small screwdriver (Flat Head), loosen the screws on the Two Conductor
Terminal Block Connector and carefully remove the Terminal Block Wires from
the Two Conductor Terminal Block Connector.
2. Using a small screwdriver, loosen the screws on the Three Conductor Terminal
Block Connector (included) and carefully insert the Terminal Block Wires into the
Three Conductor Terminal Block Connector (Red Wire = Positive and Black Wire =
Negative).
Note: Ensure the polarity of the input power is correctly matched with the Terminal
Block Pins to ensure proper functionality. Refer to the Device’s vendor manual for
further information on properly wiring the Device.
3. Tighten the screws on the Three Conductor Terminal Block Connector, to secure
the Terminal Block Wires into the Three Conductor Terminal Block Connector.
Three Conductor Terminal Block Connector
4. Plug the Three Conductor Terminal Block Connector on the Adapter into the
Terminal Connector on the Device.
Powering the Adapter
• Connect the Power Cord to the Power Connector on the Adapter and to an AC
Electrical Outlet.
1
2
3

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Connecting the Adapter to a Terminal Block
1. Before terminating the Adapter make sure that the Adapter is disconnected from
the Power Cord.
2. Refer to the vendor manual that came with the Device in order to properly terminate
the Adapter.
Note: The Terminal Wires are Red Wire = Positive and Black Wire = Negative. The
Output is 20V and the Current is 3.25A 65W.