StarTech.com ADJDINKIT User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: August 8, 2023 8:47 AM
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support
Product Diagram
ADJDINKIT
Component Function
1Rack Mount DIN Rail
Bracket
• Used to fasten the Adjustable DIN Rail onto the
Mounting Posts of a Rack
2Adjustable DIN Rail
Mount
• Loosen the Wing Nuts on either side and slide for
Variable Depth
• Allows for depths of up to 9.3 inches (23.6 cm)
3DIN Rail
• Use to securely attach DIN Rail Mountable Devices
onto a rack
• Three types of DIN Rails are included: Top-Hat,
Miniature Top-Hat, and G-Type
• DIN Rail Mounting Screws secure the DIN Rail
4Cable Management
Holes
• Allow cables to pass through to the various mounted
devices
Product Information
For the latest manuals, product information, technical specications, and declarations
of conformance, please visit: www.StarTech.com/ADJDINKIT
2U Adjustable DIN Rail Rack Mount Kit
How to Identify the LOT Code Revision Number
The Revision Number (Rev #) appears as the fth and sixth digits of the LOT code,
located on the sticker axed to the product and its packaging. If the LOT code sticker
is missing, the product is Rev 01.
Requirements
• Phillips Head Screwdriver
Package Contents
Revision 01 Revision 02 or Above
• Rack Mount DIN Rail Bracket x1
• Adjustable DIN Rail Mount with Top
Hat DIN Rail Pre-Installed x 1
• Miniature Top-Hat DIN Rail x 1
• G-Type Top-Hat DIN Rail x 1
• M5 Screws x 4
• M5 Cage Nuts x 4
• Carriage Bolts x 2
• DIN Rail Mounting Screws x 2
• Wing Nuts x 2
• Rack Mount DIN Rail Bracket x1
• Adjustable DIN Rail Mount with Top
Hat DIN Rail Pre-Installed x 1
• Miniature Top-Hat DIN Rail x 1
• G-Type Top-Hat DIN Rail x 1
• M5 Screws x 4
• M5 Cage Nuts x 4
• Carriage Bolts x 4
• DIN Rail Mounting Screws x 4
• Wing Nuts x 4
Warnings!
Ensure the weight of the equipment does not exceed the weight capacity of this
product. If the weight capacity is exceeded, personal injury or damage to the
equipment is possible. This product can support the following weight: up to 27 lb
(12.5 kg).
Installation
1. Determine the Mounting Depth according to your application.
2. Loosen the Wing Nuts (x 4) on either side of the Adjustable DIN Rail Mount by
hand. Slide the Adjustable DIN Rail Mount to match the desired Mounting Depth.
Tighten the Wing Nuts by hand.
3. Find a suitable location on the Rack to mount the Rack Mount DIN Rail Bracket.
The Rack Mount DIN Rail Bracket requires 2U of Mounting Space.
4. Follow the Rack’s Manufacturer Instructions to install the M5 Cage Nuts on the
Mounting Posts.
Note: M5 Screws and Cage Nuts are provided for convenience. Alternative mounting
*Product may vary from image
1
3
4
2

3. Insert the DIN Rail Mounting Screws through the DIN Rail. Secure the DIN Rail
Mounting Screws using a Phillips Head Screwdriver.
hardware may be needed from the Rack’s manufacturer.
5. Place the Rack Mount DIN Rail Bracket into the Rack and align it with the Mounting
Posts of the Rack.
6. Install the M5 Screws (x 4) through the Rack Mount DIN Rail Bracket, the M5
Cage Nuts and onto the Mounting Posts of the Rack. Ensure the M5 Screws are
appropriately tightened using a Phillips Head Screwdriver before mounting
equipment.
7. Mount DIN Rail Compatible Devices to the DIN Rail according to the instructions of
their respective manufacturer.
Switch Between Dierent Types of DIN Rail
The Adjustable DIN Rail Mount comes pre-installed with the Top-Hat DIN Rail. To switch
to a dierent type of DIN Rail, follow these instructions:
1. Using a Phillips Head Screwdriver remove the DIN Rail Mounting Screws that hold
the DIN Rail to the Adjustable DIN Rail Mount.
2. Place the new DIN Rail onto the Adjustable Mount.
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
Assemble this product according to the instructions. Read the entire manual and ensure the instructions are fully understood
before assembling and/or using this product.
Mesures de Sécurité
Assemblez ce produit conformément aux instructions. Lisez l’intégralité du manuel et assurez-vous que les instructions sont
bien comprises avant d’assembler et/ou d’utiliser ce produit.
Veiligheidsmaatregelen
Monteer dit product volgens de instructies. Lees de gehele handleiding en zorg ervoor dat u de instructies volledig begrijpt
voordat u dit product monteert en/of gebruikt.
Säkerhetsåtgärder
Montera produkten enligt instruktionerna. Läs hela manualen och se till att du har förstått instruktionerna innan du monterar
och/eller använder produkten.
Sicherheitsmaßnahmen
Bauen Sie dieses Produkt gemäß der Anleitung zusammen. Lesen Sie das gesamte Handbuch und stellen Sie sicher, dass Sie die
Anweisungen vollständig verstanden haben, bevor Sie dieses Produkt zusammenbauen und/oder verwenden.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
FR
www.quefairedemesdechets.fr
ASSOCIATION MAGASIN DÉCHÈTERIE
OU OU
Pensez à
donner ou
recycler
FR
安全対策
最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解してから組み立て作業を始めて下さい。
Misure di Sicurezza
Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo
prodotto.
Medidas de Seguridad
Monte este producto siguiendo las instrucciones. Lea todo el manual y asegúrese de que las instrucciones se entienden
completamente antes de montar y/o utilizar este producto.