StarTech.com ARMSLIM User manual

Manual Revision: 07/23/2018
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ARMSLIM
Slim Desk Mount Articulating Monitor Arm
with Cable Management
*actual product may vary from photos

Instruction Manual
Use of Trademarks, RegisteredTrademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ........................................................................................................................ 1
Product Overview ..................................................................................2
Installation ..............................................................................................3
Desk / Grommet Mounting ................................................................................................................... 3
Attaching the Display.............................................................................................................................. 7
Adjusting Monitor Mount Resistance................................................................................................ 9
Specications..........................................................................................11
Technical Support ..................................................................................12
Warranty Information............................................................................12

Instruction Manual
1
Introduction
Packaging Contents
Monitor Arm
Qty: 1
2-in-1 Desk/Grommet
Clamp
Qty: 1
Thumb Screws
Qty: 4
6mm Allen Wrench
Qty: 1
3mm Allen Wrench
Qty: 1
1 2 3
4 5

Instruction Manual
2
Product Overview
147 mm
<7 kg

Instruction Manual
3
Note: The Desk Clamp can support a desk / table thickness from ¾ - 3.94 in (20
– 100 mm). Depending on the thickness of your desk / table, the clamp can be
adjusted smaller by removing the 4 screws and raising the bottom portion of the
clamp as shown below.
Installation
Warning! It is the installer’s responsibility to ensure that the combined weight of all
components does not exceed the maximum 7 kg (15.43 lbs) weight capacity of the
mounting arm.
Desk / Grommet Mounting
The Monitor Arm can be clamped to a desk / table, or mounted through a grommet
hole. Instructions for both will be provided in the following sections.
Desk Mount
1. Slide the 2-in-1 Clamp (2) opening around the edge of your desk in your desired
location. Tighten by hand to secure, ensuring that the Pressure Plate is making full
contact with the bottom of the desk surface.

Instruction Manual
4
2. Slide the Monitor Arm (1) onto the base and tighten the set screw on the back of the
base, using the 3mm Allen Wrench (5).

Instruction Manual
5
2. Remove the Phillips Screw and the 2 Washers from the top of the Pressure Plate and
then slide the Hand Screw out of the clamp.
Grommet Mount
1. To convert the 2-in-1 Clamp to a Grommet Mount, turn the Clamp upside-down and
remove the 4 screws that join the clamp to the base of the monitor arm, using the
3mm Allen Wrench (5).
3. Slide the Pressure Plate back onto the Hand Screw (without the Washers or Phillips
Screw from above).

Instruction Manual
6
4. Place the base of the Monitor Arm (1) over the grommet hole and thread the Hand
Screw from below until secure. Ensure that the Pressure Plate is making full contact
with the desk surface.
Note: The Grommet Clamp can support a desk / table thickness from ¾ - 1.97 in
(20 – 50 mm)

Instruction Manual
7
5. Slide the Monitor Arm (1) onto the base and tighten the set screw on the back of the
base, using the 3mm Allen Wrench (5).
Attaching the Display
1. Carefully place your display face down on a protective surface to access the
mounting points.
2. Press in on the latch at the top of the Monitor Arm and pull up to remove the
Mounting Bracket.