State Water Heaters Sandblaster SBD30 150 NE User manual

COMMERCIAL
For more Information on the Sandblaster®contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015
800-365 0024 Toll-free USA
www.statewaterheaters.com
SCGSS00105 July 2007R
SANDBLASTER ®
Self-Cleaning Commercial Gas Water Heaters
BOOSTER
MODELS
Sandblaster ® Booster commercial gas water heaters are designed to provide high temperature water (usually 180ºF)
to commercial dishwashers. In these applications, the booster water heater is installed in conjunction with a standard
water heater, which delivers lower-temperature water to serve the non-dishwashing needs of a restaurant or other
foodservice application.
State Hydro Cannon™Self-Cleaning Device
• Significantly reduces buildup of lime, sand and other sediment in the tank
• Helps water heaters retain their rated efficiency longer and last
longer, with low water heating costs
Induced-Draft Design
• Built-in blower produces power-induced draft of makeup air prior to burner
ignition, for more efficient control of heat through the flue collector
• Eliminates performance problems caused by negative indoor air pressure
• Requires no draft hood or barometric damper
Rated as Category 1 Appliance
• Can be commonly vented with other Category 1 appliances, using standard
metal type “B” vent
Multiple Anode Rods
• Protects tank from corrosion
Three Water Connection Options
• Hot and cold water connections can be made through top, front or rear
of water heater
• Hydro Cannon device operates when front cold water connection is used
Intermittent Electronic Ignition
• Provides flame failure response in less than one second
• Includes power ON/OFF switch
• Eliminates standing pilot
Factory-installed Temperature and Pressure Relief Valve
Maximum Hydrostatic Working Pressure: 160 psi
80% Thermal Efficiency
Meets ASHRAE/IESNA 90.1-1999
• Also, design-certified by CSA International, according to to ANS Z21.10.3
standards governing storage-type water heaters
SANDBLASTER
¤

COMMERCIAL
For more Information on the SandBlaster® contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015
800-365-0024 Toll-free
www.statewaterheaters.com
SCGSS00105 July 2007R ©2007 State Industries
For complete information on limited warranties, consult written warranty, or contact the State Customer Care Center, 1-800-365-0024.
State Industries reserves the right to make product changes or improvements without prior notice.
SANDBLASTER®
Self-Cleaning Commercial Gas Water Heaters
MODEL
NUMBER
GAL
CAP.
INPUT
PER
HOUR
NATURAL/
PROPANE
FIRST
HOUR
RATING
100°F
RISE 40° 100° 140°
SBD30 150 NE 32 150,000 167 364 145 104
SBD30 199 NE 32 199,000 216 485 194 139
RECOVERY – GALLONS
PER HOUR AT °F TEMPERATURE RISE
MODEL
NUMBER
A B C D E F G H
GAS
CONN.
WATER
CONN.
APPROX.
SHIPPING
WEIGHT
(LBS.)
SBD30 150 NE 45 40 27-3/4 32-1/4 15-3/4 5 6-1/2 6 3/4" 1-1/2" 400
SBD30 199 NE 45 40 27-3/4 32-1/4 15-3/4 5 6-1/2 6 3/4" 1-1/2" 400
DIMENSIONS AND WEIGHT
CAPACITY, INPUT AND OUTPUT
BOOSTER
MODELS
B
E
F
C
D
H
G
A
1-1/2" NPI
OUTLET
1-1/2" NPI
INLET CLEARANCE
1" NPI RELIEF
VALVE OPENING
15.2cm
1.5
3.8cm
SUGGESTED SPECIFICATION
Gas booster water heater(s) shall be State Sandblaster, Model Number ___________________, with
a 32-gallon storage capacity, an input rate of __________________ BTU/HR, _________________gas,
and a recovery rate of________ gallons per hour at a________ degree Fahrenheit temperature rise, and a
maximum hydrostatic working pressure of 160 psi.
Unit(s) shall have a fan-assisted combustion system, providing a power-induced draft of makeup air prior to
burner ignition. Unit(s) shall be equipped with intermittent electronic ignition with power on/off switch, which
shall provide flame failure response in less than one second. The burner for the unit(s) shall be easily
removable. Unit(s) shall be equipped with a factory-installed temperature and pressure relief valve, and a
2-3/4" x 3-3/4" tank inspection port.
The water heater tank shall be glass-lined and protected against premature failure in the following ways:
1. Against electrolytic corrosion by multiple, factory-installed anode rods.
2.Against failure due to overheating caused by the buildup of scale, film and other sediment by a
self-cleaning device,positioned inside the tank so that it directs the flow of inlet water in such a way
that microscopic particles of precipitated solids shall be kept in suspension and exhausted from the
water heater on that or successive hot water draws.
Unit(s) shall meet or exceed ASHRAE/IESNA 90.1-1999, and be design-certified by CSA International, according
to ANS Z21.10.3 standards governing storage-type water heaters.
DIMENSIONS IN INCHES