State Water Heaters Statesman SSE-10 User manual

COMMERCIAL
The Expert’s Choice
®
500 Lindahl Parkway, Ashland City, TN 37015 • www.stateind.com
Premium Heavy Duty Electric Water Heater
■Other Standard Features
–Simplified circuitry, color-coded for ease of service
–Anode rod for corrosion protection
–Immersion manual reset high limit
–Brass drain valve
–Hinged control compartment door
–ASME T & P relief valve
■Optional International Voltages - 380, 415, 575 and 600 volts
three-phase available with Y connected elements.
■Limited Warranty Outline
–If the tank should leak any time during the first three years, under
the terms of the warranty. State Water Heaters will repair or replace
the heater; installation, labor, handling and local delivery extra.
– This Outline Is NOTA Warranty. For complete information, consult
the written warranty or State Water Heaters.
–Warranty does not apply to product installed out-side of the United
States of America or its territorial possessions and Canada.
■Meets or exceeds the requirements of ASHRAE/IES-90.1-1999.
■ASME Tank Construction – 125 psi working pressure (65 thru 120
gallons), 150 psi working pressure (5 thru 50 gallons).
■Foam Insulated – To meet rigorous state codes.
■Glass-Lined Tank – Ten tank sizes available; 5 to 120 gallon. Tank
interior is coated with glass specifically developed for water heater
use. Tank cabinet has a baked enamel finish.
■Incoloy Immersion Heaters – Heavy-duty medium watt density
elements (three/immersion heater) have incoloy sheathing and
prewired leads: provide excellent protection against oxidation and
scaling. Input ranges from 3KW to 90KW available (see
accompanying chart).
■Standard Voltages – 208, 240 and 480 volt single and three phase.
Single phase 208 and 240 are convertible to three phase. All 208 and
240 volt at 24KW and below are supplied phase convertible (single to
three and vice versa). 277 volt single phase also available. Consult
factory for 120 volt power circuit availability.
■Terminal Block – To accept copper or aluminum leads (on units with
more than one contactor).
■Immersion Thermostat – Close differential immersion type
thermostat provides the accurate temperature control required for
commercial applications (adjustable through a range of 95° to 180°F).
■120 Volt Control Circuit – 120 volt control circuit powered by fused
transformer.
■Magnetic Contactors – Heavy-duty UL rated for 100,000 cycles.
■Power Circuit Fusing (120 amp current draw and above) – Meets
National Electric Code and UL requirements that water heaters must
have internal fusing when current draw exceeds 120 amps.

RECOVERY RATE IN GALLONS PER HOUR* - Temperature Rise ˚F
Standard Btu/
KW Input Hour 30˚ 40˚ 50˚ 60˚ 70˚ 80˚ 90˚ 100˚ 110˚ 120˚ 130˚ 140˚
3 10,239 41 31 24 20 17 15 13 12 11 10 10 9
6 20,478 82 62 49 41 35 31 27 25 22 21 19 18
9 30,717 123 92 74 62 53 46 41 37 34 31 28 26
12 40,956 164 123 98 82 70 61 55 49 45 41 38 35
15 51,195 205 154 123 102 88 77 68 61 56 51 47 44
18 61,434 246 184 148 123 105 92 82 74 67 62 57 53
24 81,912 328 246 197 164 140 123 109 98 90 82 76 70
30 102,390 410 308 246 205 176 154 137 123 112 103 95 88
36 122,868 492 369 295 246 211 184 164 148 134 123 113 105
45 153,585 615 461 369 307 263 230 205 184 168 154 142 132
54 184,302 738 554 443 359 316 277 246 221 201 185 170 158
60** 204,780 819 615 492 410 351 307 273 246 223 205 189 176
75** 255,975 1025 768 615 512 439 384 341 307 279 256 236 219
90** 307,170 1229 922 738 615 527 461 410 369 335 307 284 263
*Figured at 1 KW (3413 Btu) = 4.1 gallons at 100˚F temperature rise.
**Available on 50 gallon models or larger.
To determine recovery rate per minute, divide recovery rate per hour by 60.
NSF ratings may be obtained by multiplying above figures by 0.98.
RECOVERY RATES
Optional Equipment & Construction
■Silicon Bronze Tank – Available for deionized water.
■Stainless Steel Tank – Available for deionized water.
■150 or 160 PSI Working Pressure – Available when required. Must
be specified at time of order.
■Handhole Cleanout – 4˝ x 6˝ size.
■Combination Temperature/Pressure Gauge – Dial type combination
gauge (shipped loose).
Control Options:
■Low Water Cutoff – Probe type electric low water cutoff prevents
energizing of elements in the event of low water condition.
■Override Switches – A simple form of load control allows all or part
of unit input to be controlled manually. Up to one override switch per
contactor is available.
■Indicating/Pilot Lights – For indicating element operation and/or
switch closure. Up to one indicating light available for each switch
and/or contactor is available.
■Thermostat Step – The simplest form of modulation. Allows
elements to be stepped on in groups or individually by specifying
additional thermostats (up to 1 per contactor).
Premium Heavy Duty Electric Water Heater
COMMERCIAL
The Expert’s Choice
®
500 Lindahl Parkway, Ashland City, TN 37015 • www.stateind.com
Control Options Continued:
■Sequencer – Two or three step time delay sequencer provides for
stepping of elements in groups or individually (maximum of 1 step
per contactor).
■Modulating Step – Solid state electronic control device that
modulates input to match load through progressive sequencing of
steps (up to 3 steps with maximum of 1 per contactor).
■Time Clock – Seven day clock may be programmed for up to 14 on/off
operations per week. Skip a day feature allows for weekend shutdown.
■Immersion Auto Reset High Limit – Adjustable automatic reset type.
Provides additional protection against high temperature conditions.
■Safety Door Interlock – Prevents openings of control panel door
when heater power supply is energized.
NOTE: Once door is open, the heater may be energized if necessary
for service diagnosis.
■Pressure Limit Switches – Both high and low pressure limit
switches available.
■Power Circuit Fusing – Sub-divides internal circuitry with maximum
of 60 amp fuses. Supplied as standard when required by NEC and UL.
■Alarm Horn – Horns may be furnished to warn of any condition in the
heater for which sensors have been specified.

Nominal Maximum Maximum Number* Dimensions In Inches Inlet Approx.
Model Number Gallon KW of Immersion Heaters
Inspection Outlet Relief Ship. Wt.
Capacity Input A B C D Opening Opening Opening (Lbs.)
SSE-5 5 3 1201⁄4161⁄4201⁄8582
SSE-10 10 6 261⁄8183⁄4223⁄47 116
SSE-20 20 18 27 201⁄225 8 3⁄4
3⁄4146
SSE-30 30 24 2 36 201⁄225 8 162
SSE-40 40 36 451⁄2201⁄225 81⁄4Optional 206
SSE-50 50 90 541⁄2201⁄225 8 4˝ x 6˝ 236
SSE-65 65 90 531⁄2261⁄231 113⁄4294
SSE-80 80 90 5 521⁄428 323⁄812 11⁄4
3⁄4310
SSE-100 100 90 61 28 323⁄812 354
SSE-120 119 90 65 30 341⁄4123⁄4420
*Each immersion heater contains three electric elements.
Premium Heavy Duty Electric Water Heater
COMMERCIAL
The Expert’s Choice
®
500 Lindahl Parkway, Ashland City, TN 37015 • www.stateind.com
SPECIFICATIONS
STANDARD KW INPUTS
Standard Immersion Heaters*** Number of 50A Contactors Full Load Current In Amperes
KW Single Phase Three Phase
Ratings No. of Wattage 208V 240V 480V 208V 240V 277V 480V 208V 240V 480V
3 1 3,000 14.4 12.5 10.8 6.3 8.3 7.2 3.6
6 1 6,000 28.8 25.0 21.2 12.5 16.7 14.4 7.2
9 1 9,000 1 1 43.3 37.5 32.5 18.8 25.0 21.7 10.8
12 1 12,000 57.7 50.0 43.3 25.0 33.3 28.9 14.4
15 1 15,000 1 72.1 62.5 54.2 31.3 41.6 36.1 18.0
18 1* 18,000 86.5 75.0 65.0 37.5 50.0 43.3 21.7
24 2 12,000 2 115.4 100.0 86.6 50.0 66.6 57.7 28.9
30 2 15,000 2 144.2 125.0 108.3 62.5 83.3 72.2 36.1
36 2* 18,000 173.1 150.0 130.0 75.0 99.9 86.6 43.3
45 3 15,000 3 3216.3 187.5 162.5 93.8 124.9 108.3 54.1
54 3 18,000 2 N/A 225.0 194.9 112.5 149.9 129.9 65.0
60** 4 15,000 4 4 N/A 250.0 216.6 125 166.7 145 72
75** 5 15,000 55 3 N/A 312.5 270.8 156 208.4 181 90
90** 5 18,000 N/A 375.0 324.9 188 250 217 108
*208V models use one additional immersion heater.
**Available on 50 gallon models or larger.
***Each immersion heater contains three electric elements. ASMECEC
SSE-5 thru 50 SSE-65 thru 120

Statesman Electric Water Heater Model Number Break Down
Premium Heavy Duty Electric Water Heater
Printed in U.S.A.
EC/SSE/1004 ©2004 State Water Heaters
In keeping with our policy of continuous product improvement,
specifications are subject to change without prior notice.
COMMERCIAL
The Expert’s Choice
®
500 Lindahl Parkway, Ashland City, TN 37015 • www.stateind.com
SUGGESTED SPECIFICATIONS
The heater shall be a glass-lined Statesman Premium commercial electric model No.____________________ as manufactured by State Water Heaters. Heater should
be rated at _______ KW, _______ volts, _______ phase, 50/60 cycle AC and constructed in accordance with ASME Code, shall bear appropriate symbol and be listed
with the National Board as required. Heater shall be listed with Underwriters’ Laboratories and approved by National Sanitation Foundation. All internal surfaces of the
tank shall be glass-lined with an alkaline borosilicate composition that has been fused-to-steel by firing at a temperature of 1600°F. Tank shall be cathodically protected
with adequate extruded magnesium rod. The entire vessel is to be enclosed in a round steel enclosure with baked enamel finish. Control compartment to be hinged and
shall house 120 volt control circuit transformer, transformer fusing, magnetic contactor(s), immersion style operating thermostat(s), high limit thermostat(s), element
fusing per N.E.C., and commercial grade incoloy sheathed flange mounted elements with prewired terminal leads. Temperature controls include limiting switch which
will require resetting manually in the event the temperature reaches 190°F. Foam insulation shall exceed latest requirements of ASHRAE 90.1-1999 for heat loss
efficiency. Heater shall include ASME T & P relief valve and drain valve.
Immersion
Thermostats
State Statesman
Electric
Fused
Gallon Capacity KW
Three Year Warranty
SSE 50 60 I F E