STATESMAN GH60GB User manual

Please read these instructions carefully before use and retain for future reference.
Before switching on your appliance – Always check for any damage that may have been caused in transit.
Instruction Manual
GH60GB | 60cm 4 Zone Gas Hob Black
Serial Number:

2
CONTENTS
Important Safety Instructions.................................. 2 - 3
Specication..................................................................4
Appliance Overview.......................................................4
Installation ............................................................. 5 - 10
Operating Instructions......................................... 11 - 12
Cleaning and Maintenance..........................................13
Fuse Replacement ......................................................14
Disposal Information ...................................................14
Trouble Shooting Guide...............................................15
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all of the instructions even if you feel you are familiar with the product, and
nd a place to keep this manual handy for future reference.
Important: This product is intended for domestic household use only.
When using gas appliances, basic safety precautions should always be followed:
1. Only a registered CORGI gas safe engineer can install, connect or repair this appliance. Do not
install or operate the appliance if it has been damaged.
2. Ensure the appliance is installed according to the installation instructions provided.
3. Do not change the specications or modify this appliance.
4. Prior to installation, ensure that the gas supply conditions (nature of the gas and gas pressure)
are compatible with the appliance.
5. Before installing ensure to turn o the gas and electricity supply to the appliance.
6. Check the voltage of the appliance matches the household voltage, which is located on the
rating label.
7. All appliances containing any electrical components must be earthed.
8. When installing, ensure that the gas pipe and electrical cable do not touch any part of the
appliance.
9. Ensure that the gas pipe or connectors are not bent or blocked by any other appliances.
10.The appliance is not intended to be operated by means of an external timer or remote control.
11.This appliance should only be used by adults.
12.Cleaning and user maintenance shall not be made by children.
13.Children shall not play with the appliance.
14.This appliance can be used by persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
15.Never leave the appliance unattended when in use.
16.Always ensure children are not left alone or unattended in the area of the appliance.
17.This appliance should not be used to warm or heat the room.
18.No combustible material or products should be placed on this appliance at any time.

3
19.It is not recommended to use plastic or aluminium foil dishes on the appliance.
20.Care should be taken when using this appliance as the cooker top can become extremely hot.
21.Do not allow clothing or any items other than suitable cookware contact with the appliance.
22.Ensure saucepan handles do not overhang burners that are switched on as they may become
hot.
23.It is not recommended to store anything on top of the appliance.
24.After use, always ensure that burners are switched o.
25.After use the appliance will stay hot for some time, even after it is switched o. Keep children
well away at all times.
26.Do not store ammable liquids and materials on or near the appliance.
27.Ensure that the kitchen is well ventilated or a mechanical extractor hood is tted.
28.It is not recommended to use this appliance if it comes into contact with water or with wet
hands.
29.Do not spray aerosols in the vicinity of the appliance whilst in operation.
30.When frying foods always try to ensure that food is as dry as possible as frost or moisture on
food may cause hot fat to bubble up and over the sides of the pan.
31.Do not try to move a pan of hot fat, always allow to completely cool.
32.The manufacturer shall not be responsible for any damages to persons or property caused by
incorrect installation or use of the appliance.
WARNING: In the event of a re, do not take any risks. If safe, turn the burner o, leave the
building and call 999. Never throw water over it and do not tackle the re yourself.
WARNING: In the event of a gas leak, stop using the appliance and ensure that all control
knobs are set to the o position. Open a window to ventilate and leave the room and contact a
registered CORGI gas safe engineer by the use of a neighbours phone or a mobile phone but not in
the vicinity of the appliance. Do not switch on/o any electrical appliances including lights. Gas can
have the smell of rotten egg or garlic.

4
Supplier Name
Model
Type of Hob
Pan Support
Top Plate
Dimensions (H x W x D) mm
Ignition Device
Type of Ignition
Gas Connection
Electric Supply
Energy Eciency Per Gas Burner
Statesman
GH60GB
Gas
Cast Iron
Black
90 x 600 x 515
Continous Ignition
Electricity Cord
G1/2 Thread
220 - 240V, 50Hz/60Hz, 0.6W
G20 20mbar 54.95%
Triple Crown
57.38%
Semi Rapid
Burner
53.74%
Auxiliary
N/A
APPLIANCE OVERVIEW
1. Triple Crown Burner
2. Semi-rapid Burner
3. Control Knobs
4. Auxiliary Burner
Accessories
TECHNICAL SPECIFICATION
1
2
3
4
Bracket (4) Sealing Strip (4) Screw (4) Injector (4) Gas Pipe Bend (1)
Energy Eciency Per Gas Hob
Triple Crown
(Top left)
3.6kW
Semi Rapid x2
(Rear & front right)
1.75kW
Auxiliary
(Front left)
1kW
Burner Power

5
INSTALLATION
This appliance should only be installed by a registered CORGI gas safe engineer. Before installing
the appliance ensure that the area that you have selected is suitable and allows enough ventilation
for the appliance. The appliance can be tted into a kitchen unit or 600mm wide worktop, providing
that the stated minimum distances are allowed. Ensure that the selected worktop or unit and all
surrounding materials are made of non-ammable materials. Install a mechanical ventilation device.
Important: Always ensure the appliance is well ventilated and the air inlet and outlet are not
blocked.
Product Dimensions
W (mm) D (mm) H (mm)
600 515 90

6
FO 0813
400mm
560mm
490mm
400mm
700mm
0in.
0mm
60mm
0mm
M
2
60
• Cut a hole in the worktop that corresponds with the above diagram.
• The edges of the hob must be a minimum distance of 60mm from the rear wall.
• 700mm between the highest point of the hob surface (including the burners) and the underside of
any horizontal surface directly above it.
• 400mm between the hob surfaces, providing that the underside of the horizontal surface is in line
with the outer edge of the hob.
• The underside of the horizontal surface must be at least 50mm away from the outer edges of the
hob.
• 50mm clearance around the appliance and between the hob surface and any combustible
materials.
• You must have a gap of a minimum of 25mm and a maximum of 74mm between the underneath
of the appliance and any surface that is below it.
45 mm

7
515
Top View Bottom View
Important: Ensure the worktop is heat-resistant to avoid deformation caused by the heat radiation
from the burners.
• Remove the pan supports, the burner lid and ame spreader and carefully turn the appliance
upside down and place onto a cushioned mat. Taking care not to damage the ignition devices
and ame safety devices.
• Apply the provided Sealing Strip around the edge of the appliance. Ensuring not to leave a gap
or overlapping the sealing agent.
• Locate the screw holes on the base of the appliance.
• Place the bracket over the matching holes and secure with a screw ensuring to allow the bracket
to move.
• Carefully turn the hob back over and then gently lower into the cut
hole.
• On the underneath of the hob, adjust the brackets into a position that
secures the appliance to the worktop or unit. Screw can now be fully
tightened.
(A) SEALING STRIP
(C)S CREW (B)B RACKET
WARNING: Do not use a silicon sealant to seal the appliance
against the worktop or unit. This will make it dicult to remove the
appliance from worktops or units in the future, particularly if it needs
to be serviced.
600

8
Connecting to the Gas Supply
WARNING: This appliance must be installed by a registered CORGI gas safe engineer. The
appliance must be installed and connected in accordance with the manufacturer’s instructions and
to the relevant British Standards.
Note: This appliance is supplied to run on LPG and natural gas. Conversion for use on LPG and natural gases must
only be undertaken by a registered CORGI gas safe engineer.
seal
G1/2"Female󴖦coupler
The󴖦gas󴖦rail
seal
The󴖦gas󴖦rail
NG > LPGLPG > NG
Gas supply replacement and installation guidelines:
• It is law that all gas appliances are installed by competent persons in accordance with the
current edition of the Gas Safety Installation and Use Regulations.
• It is in your interest and that of safety to ensure compliance with the law.
• In the UK, GASSAFE registered installers work to safe standards of practice. The appliance
must also be installed in accordance with the current edition of BS 6172. Failure to install the
appliance correctly could invalidate the warranty, liability claims and lead to prosecution.
I3+(28-30/37) G30 Butane at28-30mbar and G31 Propane at 37mbar
I3B/P(30) G30 Butane and G31 Propane at 30mbar
BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT, LU, LV, PT, SK, SI
I2H/I2E/I2E+
BE, CY, DK, EE, GB, HU, IT, LT, NL, NO, SE, SI, SK, RO, HR,
TR, BG, IS, LU, MT, FI
G20 M ethane at 20mbar
II2H3+ CH, CZ,ES,GB,GR,IE, IT,PT,SI
G20 at 20mbar, G 30 B utane a t 28-30mbar a nd G 31
Propane at 37mbar
II2H3B/P(30)
AT,CH,CZ,DK,ES,FI,GB,GR,IE,IS,IT,PT,SE,SI,SK,DE,LU,GE,FR
G20 at 20mbar, G30 Butane and G31 Propane at 30mbar
II2E+3+
CH,CZ,DK,FI,GR,SE,SI,SK
BE, FR
G20/G25 a t 20/25mbar, G 30 B utane a t 28-30mbar and
G31 Propane at 37mbar
II2H3B/P
I2H: G20 Methane at 20mbar
I3B/P: G30 butane and G31 propane at 30mbar CH,CZ,DK,FI,GR,SE,SI,SK
II2H3+ CH, CZ,ES,GB,GR,IE, IT,PT,SI
I2H: G20 Methane at 20mbar
I3+: G30 butane at 30mbar and G31 propane at 37mbar
II2E+3+ BE, FR,
I2E: G20 Methane at 20mbar
I3+: G30 butane at 30mbar and G31 propane at 37mbar

9
Gas Adjustment
All adjustments when converting from one gas to another must be done by a registered CORGI gas
safe engineer.
WARNING: Ensure the gas and electricity supply to the appliance are switched o before
making any adjustments to the appliance.
Change the Injector of the Burners
• Remove the pan support, burner lid and ame spreader.
• Unscrew the injector using a 7mm box spanner and replace with new injector correct for the new
gas supply. Ensuring that the new injector is rmly tightened.
• Carefully reassemble all the Burner Cap, Burner Crown and Flame Spreader.
Injector
GH60GB

10
WARNING: Do not dismantle the Gas Tap Shaft: In the event of a malfunction, change the
whole tap.
• Before replacing the Flame Spreader and Burner Cap, ensure that the Injector is not blocked.
• A full operational test and a test for possible leaks must be carried out after a gas conversion.
• After completing conversion, the quailied gas engineer will need to mark “V” on the right gas
category to match with the setting on the rating plate. Remove the previous setting mark.
Control handle
Sealing ring
Tap
Important: For butane/propane gas, the adjusting screw must be tightly screwed in.
• Ret the control knobs to each Gas Tap.
• Test the ame by quickly turning the Control Knob from maximum to minimum, if the ame goes
out then you will need to make further adjustments to the gas ow.
• Repeat the process again until the gas ow is correct.
Adjustment of Minimum Level of the Flame
• Ignite the burner and set to MIN
• Remove the Control Knob and place a small bladed screwdriver in the centre of the Gas Tap
Shaft.
• Adjust until a steady ame is reached, about 3 – 4mm and does not extinguish when the Control
Knob is turned down to MIN.
• Repeat this procedure for all burners

11
OPERATING INSTRUCTIONS
The appliance is tted with a ame failure safety device on each burner, which is designed to stop
the ow of gas to the burner in the event of the ame going out.
• To light a burner, press in the relevant control knob and turn in an anticlockwise direction to the
maximum setting.
• Keep the Control Knob depressed, the automatic ignition for the burner will, automatically ignite
the ame.
• Keep the Control Knob depressed for a further 15 seconds after the ame has ignited.
• If the ame does not ignite or stay on, then repeat the process.
• The required setting can now be selected by turning the control knob.
• To switch the burner o, turn the Control Knob fully clockwise to the o position.
• In case of a power cut, the burners can be manually lit by using a match, although extreme care
should be taken.
Important: Once liquids start to boil, reduce the ame so a gentle boil is reached. This will help
prevent over spills.
Black Circle: Gas o
Large Flame: Maximum setting
Small Flame: Minimum setting

12
Choosing the Correct Cookware
The diameter of the bottom of the pan should correspond to that of the burner.
Important: Do not use cookware that overlaps the edge of the burner.
WARNING: Do not touch burners or trivets whilst in use or for a good period after use as
they will be extremely hot. It is not recommended to use roasting pans, frying pans or grill stones
simultaneously on several burners as this may damage the appliance.
NO YES
is
lid half off
one side.
them that they increase the temperature in
this area and may cause damage.
the trivet.
support as serious damage to the
appliance may result.
cooktop
Burners
Pans
Minimum Maximum
Triple Crown
Semi Rapid
Auxiliary
200mm
160mm
120mm
240mm
180mm
160mm

13
CLEANING AND MAINTENANCE
WARNING: Allow burners to cool before cleaning. Do not clean parts in the dishwasher.
Cleaning the Top Plate
Before cleaning and maintenance ensure the appliance is disconnected from the mains electricity
supply.
• Regularly wipe the appliance using a soft cloth with warm water and a little washing up liquid,
ensuring to thoroughly dry before use.
• It is not recommended to clean the appliance with abrasive cleaners, cloths or sharp objects as
this may damage the appliance.
• If the appliance becomes heavily soiled use a suitable cleaner for gas hobs. All cleaners should
be thoroughly removed before use.
• Thoroughly remove salty foods or liquids from the appliance as soon as possible to avoid the risk
of corrosion.
• Stainless steel parts of the appliance may become discoloured over time. This is normal due
to the high temperatures. It is recommended to wipe these parts with a cleaner suitable for
stainless steel.
Cleaning the Pan Support and Control Handles
• Remove the pan supports.
• Clean these and the control knobs with a clean damp cloth, washing up liquid and warm water.
For stubborn soiling, soak beforehand in warm water and a little washing up liquid.
• Dry everything with a dry clean cloth before replacing.
Cleaning the Burners
• Remove the burner lids and ame spreaders, these can be soaked in hot water and washing up
liquid. Once clean dry thoroughly.
• Wipe the xed parts of the burner with a clean damp cloth and dry afterwards.
• Gently wipe the ignition device and ame failure safety device with a well wrung out cloth and
immediately wipe dry.
• Check that the ignition shaft is clear from debris.

14
RE-ASSEMBLING THE AUXILIARY, SEMI-RAPID AND TRIPLE-CROWN
BURNER
1/2/3
4
5
6
7
Burner Lid
Flame Spreader
Burner Cup
Ignition Needle
Thermocouple
• Place the ame spreader on the burner cup so that the ignition and ame failure safety device
extends through the holes in the ame spreader. The ame spreader should click into place.
• Position the burner lid onto the ame spreader so that the retaining pins t exactly into the
supplied holes.
Important: Do not mix up the burner lids.
1
2
3
4
5
6
7
DISPOSAL
The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be disposed of in normal unsorted municipal
waste.
Old appliances must be collected separately in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when
you dispose of the appliance it must be separately collected. Consumers should contact their local
authority or retailer for information concerning the correct disposal of their old appliance.
FUSE REPLACEMENT (MOULDED PLUG TOP – CLASS I OR II)
Remove the fuse cover with a small at head screw driver.
Take out the fuse and replace with a new fuse of the same Amp.
Replace the fuse cover and push back into place. FuseCover
Triple Crown Burner Auxiliary & Semi Rapid Burner

15
Trouble Shooting
Fault Possible Causes Solution
Not Ignited No spark Check the electric supply
The burner assembly is not put
together correctly
Ensure the burner assembly
is securely tted together
The gas supply is closed Open the gas supply
completely
The fuse has blown Change the fuse
Inconsistent/unstable
ame
The gas supply is not completely
open
Open the gas supply
completely
The burner assembly is not put
together correctly
Ensure the burner assembly
is securely tted together
The ignition shaft has debris in it Clean the debris with a dry
cloth
The burners are wet Turn down the boiling pan
and wipe dry once cold
The holes in the ame spreader
are clogged
Clean the ame spreader.
Refer to ‘Cleaning and
Maintenance’
Noise made when ignited The burner assembly is not put
together correctly
Ensure the burner assembly
is securely tted together
Yellow Flame The holes in the ame spreader
are clogged
Clean the ame spreader.
Refer to ‘Cleaning and
Maintenance’
Dierent gas is used Check the gas used is
correct
Gas Smell Gas leakage Stop using the appliance
and close any functioning
burners. Open a window
to ventilate and contact
a registered CORGI gas
safe engineer by the use
of a neighbours phone or a
mobile phone.
Note: Do not switch on/o
any electrical appliances
including lights. Gas can
have the smell of rotten
garlic or eggs.
If you are having problems with your appliance, please use our troubleshooting guide below.
If you are unable to resolve the issue using this guide please ring our Customer Service Department
on 0844 848 5861. Please have the model code and purchase information available.

0844 848 5861
38 Bluestem Road,
Ransomes Europark
Ipswich, IP3 9RR
Disclaimer: Statesman operate a policy of continual improvement and development.
We therefore reserve the right to change/alter the specication and appearance of our appliances without prior notice.
All diagrams and images shown in this manual are for illustration purposes only.