Stiga ELITE T8624 User manual

MODEL NO.
T8624
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2L-7627-00
2017 Escalade Sports
Ó
“ E L I T E ”
T A B L E T E N N I S T A B L E

P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
1-866-873-3528
2L-7627-00
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for
kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 9/16” Wrenches, Two 7/16” Wrenches (Ratchet and 9/16”, 7/16” Sockets are
recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten the
and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
P R E - A S S E M B L Y T I P S
2017 Escalade Sports
Ó

1/4"
Plastic
Washer Washer
Plastic
3/8"
28 30
31
32 5
34
35 37
1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16
SMS
#8-32 X 1 1/4
Sheet Metal Screw 3/8" Long Spacer
3/4" Long Spacer
39
36
29
HARDWARE IDENTIFIER
3/8-16
Nyloc
Locknut 1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
3/8-16X2 3/4 Hex Head Bolt 1/4-20 X 2 1/2” Hex Head Bolt 3/8 Push Nut
13 24 11
(Qty. 4) (Qty. 12)
(Qty. 12)
(Qty. 4) (Qty. 4) (Qty. 172)
(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 12) (Qty. 8)
(Qty. 8) (Qty. 8) (Qty. 4)
38
(Qty. 4)
1/4-20 Wing Nut
#10-24
Locknut
(Qty. 4)
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 4)
33
Sorting your hardware ahead of time will speed up assembly time. Sort
all your hardware now so it will be ready before you start assembly.
NOTE:
3

1A. Attach Caster Wheels (#9 & #10) to Caster Beam. Slide a Caster Wheel with Lock (#10) through Caster Beam (#8) and
secure it with a Push Nut (#11) as shown in Figure 1. Gently tap the Push Nut (#11) with a hammer or rubber mallet to
secure it in place. On the other end of the Caster Beam attach a Caster Wheel without Lock (#9). Make sure you have one
Caster Wheel with Lock and a Caster Wheel without Lock for each Caster Beam. Repeat step for second Caster Beam.
1B. Attach Tube Plugs (#14) to Caster Beams (#8) as shown in Figure 1. Repeat step for second Caster Beam.
8
11
9
10 14
Caster
with
Lock
Caster
without
Lock
11
HARDWARE NEEDED
3/8 Push Nut
(Qty. 4)
NOTE: Make sure logo is
right side up and
facing as shown.
1
Figure
4
ASSEMBLY TIP
On the top of each page you will find a picture of the
Hardware Needed (to scale) along with the Quantity,
Key# and Description. You can lay the hardware on
the picture to identify and sort the hardware.
Having a second person sort hardware and
hold parts will speed up assembly time
and make it easier to assemble your table.
NOTE:

8
10
10
43
2. Lay Support Plates (#43) on Caster Beam (#8) to line up holes, the distance between middle holes to
side holes is different, see Front View of Figure 2. Attach Stop Spools (#12) and Support Plates
(#43) to side of Caster Beam without logo with Bolts (#13) and Nuts (#28) as shown in Figure 2.
DO NOT tighten completely yet this will be done in a later step. Repeat step for second Caster Beam.
Longer
Shorter
Longer
Shorter
Match holes in Support Plate (#43)
with Caster Beam (#8).
2813 3/8-16 X 2 3/4 Hex Head Bolt
(Qty. 8) 3/8-16 Locknut
(Qty. 8)
Front View
HARDWARE NEEDED
2
Figure
5
8
Logo on
this side
13
28
43
12

3. Attach Wood Bottom Board (#15) to Caster Beam Assemblies (#8)
as shown in Figure 3. Turn Caster Beams as shown and attach
board with four Carriage Bolts (#31) and four Wing Nuts (#32).
Tighten Wing Nuts securely.
32
31
(Qty. 4)
1/4-20 Wing Nut
8
Caster
with
Lock
HARDWARE NEEDED
1/4-20 X 3 1/4 Carriage Bolt
(Qty. 4)
NOTE: Make sure logos are right side up and
facing the outside as shown.
3
Figure
6
32
31
15
31
32 Caster
with
Lock
8
43
Note: Support Plate (#43)
is on the inside of Caster
Rail (#8) as shown.
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
CAUTION:

4. Attach Strut Tubes (#17) and Red Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 4.
a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster
Beam (#8) as shown in the Top View and Figure 4.
b) Slide one Hex Bolt (#27) through one linkage (#16) one Spacer (#36) pass through Caster Beam (#8), followed by one
Plastic Washer (#39), Strut Tube (#17), another Plastic Washer (#39), inner Support Plate (#43) and Lock Nut (#28).
c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.
d) Tighten Nuts (#28) on Bolts (#13) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely.
17
8
39
16
13
8
43
Note: Linkages & Strut
tubes must be turned as
shown or table will not
operate correctly.
36
27
28
17
16
43
39 12
36
8
28
13
(Inner Plate)
27
28
TOP VIEW
3/8-16
Locknut
(Qty. 4)
28
HARDWARE NEEDED
27 3/8-16 x 3 1/2 Hex Head Bolt
(Qty. 4)
36 39
3/4" Long Spacer
(Qty. 4)
3/8" Plastic
Washer (Qty. 8)
4
Figure
7

ASSEMBLY TIP
Note: This end has NO stripe
and NO indentations.
5
21 22
Slot in
U-Clip
Note: All Indentations
guides in table top are
small so look closely.
1
5. Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the
shipping container to protect the painted surface of table top.
6. Align the ”U” Support (#21) on Table Top (#1) as shown in Figure 5.
7. Align all four holes in each U-Clip (#22) with the four Indentations in table
top. Be sure that Slot in the Three U-Clips (#22) all face the same direction
toward the end of the table with no stripe and no Indentations. Secure U-
Clips (#22) with Screws (#5) as shown in Figure 5 & Detail A.
Note: All four holes in each U-Clip (#22) must align with four
Indentations in table top. See Detail A.
Note: Indentations in table top are small so look closely.
Detail A
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#22) BE
TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY, YOU WILL DO
IRREPARABLE DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT TO OPEN IT TO THE
PLAYING POSITION.
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
21
5
Figure
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 12)
Table top can be set on two saw horses. Although this will make
assembly easier it is not necessary to complete assembly. Always use
shipping container to protect the painted surface of the table top.
CAUTION: Make sure that the table top is secure on the
sawhorses and NEVER leave the table top unattended.
NOTICE
NOTICE
8

22
35
1
If you want to see a video on how to insert Screw (#35) go to:
http://www.escaladesports.com/customer-service/instruction-videos
Or
Scan with your smartphone:
8. Rotate U-support (#21) that is on bottom of Table Top until you see the
screw holes in the slots of U-clips (#22). If necessary Slide U-support (#21)
side to side and back and forth to see holes. See Figure 6 & Detail B.
9. Insert Screw (#35) through slot in U-clip (#22) and into U-support (#21).
See Figure 6 & Detail B. Thread screw all the way into U-support until it
touches the back of the tube. There should be about 3/8” of screw (#35)
left sticking out. Repeat for second Screw (#35) and U Clip (#22).
Note: To aid in assembly use a cordless drill but DO
NOT over tighten screws. Wear safety glasses.
35
HARDWARE NEEDED
#8-32 X 1 1/4
Sheet Metal Screw
(Qty. 2)
Detail B
Note: This end has NO stripe
and NO indentations.
6
Figure
9
21

20
25
5 5
Detail C
Note: Indentations
in table top are small
so look closely.
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 28)
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE
AND USE CAUTION BECAUSE YOU COULD OVER-TIGHTEN THE
HARDWARE AND STRIP SCREW IN WOOD DOING IRREPARABLE
DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
NOTICE
10. Assemble parts to the bottom of the table top with Screws (#5) as shown in Figure 7,
Detail C and Detail D.
a) Align the holes in the Mounting Brackets (#25) & (#20) with Indentations in table
top assembly and secure with screws (#5) as shown. All holes in each Mounting
Bracket must align with Indentations in the top. See Figure 7 and Detail C.
b) Align the holes in the two U-Support Clips (#6) with Indentations in table top. Be
sure that the two U-Support Clips (#6) are positioned exactly as shown in Figure 7 &
Detail D.
6
5
Detail D
6
7
Figure
10

8A
Figure
8B
Figure
Note: You Will Need one hinge in position A and one in position C for the next page. Hinges
are universal and can be rotated into either position A or C. See Figure 8A. Or
Scan with your Smartphone/Tablet:
If you want to see a video on how to rotate hinges go to:
http://www.escaladesports.com/customer-service/instruction-videos
1. Determine in which position your hinges are rotated, if you already have one hinge in Position
A and one in Position C continue to next page.
2. If you have two hinges in Position A rotate one hinge into position C as shown in Figure 8A.
3. If you have two hinges in Position C rotate one hinge into position A as shown in Figure 8B.
FLIP HINGE ASSEMBLY
180 DEGREES
ROTATE BRACKET
180 DEGREES.
NOTE MAKE SURE TO
ONLY ROTATE BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
ABC
CB A
FLIP BRACKET 180
DEGREES.
NOTE MAKE SURE TO
ONLY FLIP BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
FLIP HINGE ASSEMBLY
180 DEGREES
Rotating hinge from position A to position C.
Rotating hinge from position C to position A.
NOTE:
11

9
Figure
Note: Hinges must always be positioned as shown, with the “elbow” of the hinge pointing
toward the bottom of the table. In the correct position hinge will look like a “V“,
rotate hinges into position if necessary.
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREWS IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
11. Align the holes in the Hinge Bracket Assembly (#18) with indentations in table
top. Be sure that the straight part of the hinge is facing toward the middle of
the table and placed exactly as shown in Figure 9, Detail E1 & E2.
NOTE:
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 8)
Detail E1
Detail E2
NOTICE
18
5
Hole on the straight
leg of hinge should
be facing up
18
NOTE: If using electric
screwdriver set at low
torque. Do not over
tighten screws.
The “elbow“
of the hinge should
be pointing towards the
bottom of the table
Hole on the straight
leg of hinge should
be facing up
The “elbow“
of the hinge should
be pointing towards
the bottom of the table
(Position A)
(Position C)
The straight leg on
both hinges should
be facing toward the
middle of the table
12

38
34
33
29
19
Leg Brace
24
25 20
Detail F
26
12. Attach legs (#19) to Mounting Brackets (#20 & 25) with Hex Bolt (#24), two Plastic Washers (#38) and Locknut (#34). Attach
leg brace to Leg Mounting Bracket (#25) with Phillips Head Screw (#29) and Locknut (#33) as shown in Detail F.
13. Attach leg caps (#26) to bottom of the legs (#19) as shown in Figure 10. Repeat the last two steps to instal the second leg.
10
Figure
13
HARDWARE NEEDED
1/4-20 X 2 1/2” Hex Head Bolt
24
(Qty. 2)
1/4"
Plastic
Washer
(Qty. 4)
38
34
1/4-20 Nyloc Locknut
(Qty. 2)
29
#10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 2)
33
#10-24
Locknut
(Qty. 2)

IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREWS IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
NOTICE
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 29)
14
14. Lay out Rails (#2, #3, #23 & #44) around
edges of table top. See Figure 11.
16. Line up holes in rails with Indentations in table top and
secure using Screws (#5). See Figure 11 & Detail H.
2
*NOTE: Legs not
shown for clarity.
Note: All Indentations
guides in table top are
small so look closely.
Detail G
15. Place Ball Holder end Plugs (#7) in both ends of Ball
Holder End Rail (#4). See Figure 11 & Detail G.
23
3
5
74
44
44
23
Stiga logo
on this side
Stiga logo
on this side
Bends on Rails
face each other
5
Detail H
11
Figure

Detail J
5
40
40
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 12)
17. Attach Corner Protectors to Table Top using Screw (#5) as shown in Detail J & K.
NOTE: Prepare an area for the assembly of the second table top half. If necessary, move the first table
top half aside with the aid of a helper. Be sure to place it in a location where it won't be disturbed or
damaged. If setting on its side, be sure to place the bottom edge no less than 12 inches away from the
wall. Also be sure to place carpet or pieces of the shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a heavy object to keep it from sliding.
19. Repeat steps 5-17 to complete second Table Top Assembly.
12
Figure
*NOTE: Legs not
shown for clarity.
15
Detail K
NOTE: There are no Indentations guides for the nut plates (#45) on the table top.
18. Attach Net Plate (#45) as shown in Detail L & Detail M. Make sure the Nut
Plate is flush with the corner of the table and make sure to use the top three
holes in the nut plates. Note: Nut Plates Mount to one Table Top Only.
5
45
Detail L
Flush
Flush
No screw in
this hole
45
Detail M
No screw in
this hole

DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
TUBES UP
Table Top
Assembly
21
U-Support
17
Strut Tube
8
8
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes (#17).
17
Strut Tube
PIVOT STRUT
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, U-
SUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
TOPS IN A VERTICAL POSITION. DO NOT OPEN
Y TO ASSEMBLE. TABLE TOPS ARE
LEGS AND TR
HEAVY -
ALONE!
DO NOT ATTEMPT TO ASSEMBLE
HEAVY -
AT LEAST TWO (2) ADULTS ARE NEEDED TO
16
13
Figure
20. Attach Table Top Assembly to Base Assembly as shown in
Figure 13. Pivot Strut Tubes (#17) up as shown; then, with
at least one adult on each side of Table Top, lift top and
align ends of U-support tube (#21) with tops of Strut Tubes
(#17) as shown in Figure 13. Lower the table in a
controlled manner and as even as possible so the Strut Tube
goes in the U-Support evenly. Carefully slide tubes together.

ATTENTION: If hinge is positioned as
shown here (Detail N), Rotate the hinge as
shown in Detail O. Do not take hinge off.
18
Hinge Assembly
with “elbow”
pointing down.
18
17
17
38
Plastic Washer goes
between Strut Tube
(#17) and Hinge (#18)
30
38
34
30
17
34
HARDWARE NEEDED
30 38
1/4" Plastic
Washer
1/4-20 Locknut
(Qty. 2) (Qty. 2)
1/4-20 X 1 1/2 Phillips
Truss Head Screw
(Qty. 2)
CAUTION: Position hinges exactly as
shown in Detail O or table will not
operate correctly and could be damaged.
34
38
30
18
17
Elbow
17
Detail N
Detail O
Incorrect position
of hinge with elbow
pointing up.
In the correct position Hinge #18
will look like a “V” when attached
to Strut Tube (#17).
Hinge Assembly
with “elbow”
pointing down.
Correct position
of hinge with elbow pointing down
Elbow
21. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 14 & Detail O. With
hinge positioned as shown, align hole in hinge with hole in Strut Tube and attach with
¼” Screw (#30), Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38) goes
between Strut Tube and Hinge. Tighten nut securely. Repeat for other Hinge.
CAUTION: Hinges must be positioned exactly as shown or table will not
operate correctly and could be damaged.
Note: If hinge (#18) is positioned as shown in Detail N, you will have to rotate the hinge
to the position shown in Detail O. DO NOT unscrew the hinge, you can rotate the hinge
without unscrewing it from the table.
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE
INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS
BODILY INJURY OR PROPERTY DAMAGE.
14
Figure

16 5
22. Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#5) as
shown in Figure 15. Align holes in U-support with holes in Strut Tubes
and thread screw (#5) into hole in Strut Tube (#17). Tighten screws all the
way but be careful not to over tighten as you could strip threads on screws.
16
16
21
19
34
37
24
24
34
37
17
17
Spacer goes
between Linkage Arm
(#16) and Leg (#19)
5
19
DO NOT OPEN THE TABLE TO PLAYING
POSITION UNTIL BOTH TOPS ARE
INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD
BE KNOCKED OVER CAUSING SERIOUS
BODILY INJURY OR PROPERTY
DAMAGE.
34
24
HARDWARE NEEDED
1/4-20 Locknut
(Qty. 2)
37 5
3/8" Long Spacer
(Qty. 2)
#8 X 9/16
Screw
(Qty. 2)
23. Attach Linkages (#16) to Leg (#19) as shown in Figure 15. Pivot Leg
(#19) out from the table top and pivot both linkages (#16) up and align
hole in Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg (#19)
using Hex Head Bolt (#24), Spacer (#37) and Locknut (#34). Spacer
(#37) goes between Linkage and Leg. Attach other Linkage to Leg
the same way. Tighten nuts securely.
18
15
Figure
24. With at least two adults, repeat Steps 20-23
for other table top assembly.
Note: Make sure to
install screw #5.
Note: Make sure to
install screw #5.
1/4-20 X 2 1/2” Hex Head Bolt
(Qty. 2)

19
TO CLOSE:
1. Remove net and net posts from table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
plastic clips are engaged. Then continue
lifting until closed.
4. Raise other table half in the same manner.
....as shown in Figure 19.
TO OPEN:
1. Hold center of top edge. Gently pull outward to midway position.
.... Continue to pull until disengaged from plastic clips and legs rest on the
....floor as shown in Figure 16A and 16B. Do not leave table partially
....opened at midway position.
2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 17.
4. Attach net posts and net to table as shown in Figure 18.
NOTE: Net will be tight. It may be necessary to stretch net. This will insure
proper net tension.
PLAYING POSITION
IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 19)
1. Set the table to the Playing Position and lock hinges as shown in
....Figure 17.
2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create
....enough slack to align table tops. See (Pg.6).Figure 3
3. With the help of two other adults, push the two table top halves so
.... they are in line with each other and re-tighten the Wing Nuts (#32) as
....shown in .Figure 19
OPENING AND CLOSING INSTRUCTIONS
Push to lock hinge.
Plastic
Clip
EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR CHILDREN NOT
PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE TABLE.
IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.
DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.
Midway
Position
PLAYBACK POSITION
Hinge
Locked
To lock hinge push up on
the table and push hinge
as shown in Figure 16B.
STORAGE POSITION
TOP VIEW
Figure 16A Figure 16B
17
Figure
CAUTION:
18
Figure
19
Figure
Caution: To prevent damage to the net system
and/or table top, the post assembly must be
pivoted toward side of table before lifting table
tops to storage position. Loosen knob and
pivot net post toward table side as far as it will
go. Re-tighten knob.

3. Storage
Caution: To prevent damage to the net system and/or
table top, the post assembly must be pivoted toward side
of table before lifting table tops to storage position.
Loosen knob and pivot net post toward table side as far
as it will go. Retighten Knob.
Knob
by firmly gripping the vertical net post within height adjustment slot
20