Stiga T8755W/F User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
Leave bolts slightly loose until you are instructed to tighten them.
4. To make assembly as easy as possible, place all parts of the table tennis in a cleared area and
remove the packaging material. Organize all parts as per parts identifier in the assembly manual.
Do not dispose of the packing material until assembly is completed.
5. Avoid scratching table tennis top and metal tube parts during the assembly process.
6. Assemble product on clean, level and flat surface.
7. Take time to correctly orientate parts exactly as per each assembly diagram.
8. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
O W N E R ’ S M A N U A L
Please visit our website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Escalade Sport products may be manufactured and/or licensed under the following patents.
6120397 , 5816957 , 5769744 , 5119741 , 4911085 , 4717157 , D460140 , D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2021 Escalade Sports
R
C
R
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
R
READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS
CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!
Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as
Manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT
TO THE STORE!
Be sure to write your model number and serial number here
for future reference. You can find these numbers printed on
the bottom of the table.
MODEL NO.: T8755W/F
DATE CODE : CPSIA#2-T8755W/F-_______-SY
PURCHASE DATE : _______________________
Please provide model number and/or part number of the product and/or part when you call or write. These numbers can be found on the
product, packaging, and/or in this Owner’s Manual.
CAUTION:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [e-mail]
Mailing Address
(correspondence only):
Escalade Sports
PO Box 889, Evansville, IN 47706
Physical Location:
Escalade Sports
817 Maxwell Ave.
Evansville, IN 47711
V.2

- 2 -
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple
maintenance steps, you will add to the life of your new table.
The top (playing surface) of your table is made of Mid-Density Board. Like all products made of wood, it
can be affected by atmospheric changes in both temperature and humidity. This may cause a slight
sag or distortion as the top expands or contracts. This is normal and should not cause concern as it
does not detract from the play or utility value of the table. After assembly of the table, you can minimize
the effects of temperature and humidity changes by storing the table in a dry area when table is not
in use.
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes can cause the wood to warp, swell, crack or blister. When your table is not in
use, it should be stored in a dry area. Due to the nature of particle board, table top may bow.
Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
THE TABLE TOP
STORAGE OF YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table’s playing
surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING PRODUCTS on your table’s playing
surface.
CLEANING YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease
of use of your table.
MAINTENANCE OF YOUR TABLE
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING
POSITION and move table several inches in different directions to find the best location for the table.
If the floor is extremely unlevel, table may not play or operate properly.
I
The table has leg levelers - Adjust leg levelers as required.
f table is high in the center, shim up under the outer legs.
UNLEVEL FLOORS
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or
blister.

- 3 -
HARDWARE IDENTIFIER (To Scale)
PARTS IDENTIFIER (Not to Scale)
P1 - Table Tennis Table Top
Frame Assembly
(2 pcs)
P2 - Leg (4 pcs) P3 - Leg Support Tube
(2 pcs)
P6 - Net Post
(2 pcs)
P7 - Net (1 pc)
H1 - 8 mm x 20 mm
Hex Head Bolt
(8 pcs)
H5 - 8 mm x 20 mm
Flat Washer
(32 pcs)
H6 - 8 mm Nylon
Lock Nut
(22 pcs)
H2 - 8 mm x 40 mm
Hex Head Bolt
(8 pcs)
H3 - 8 mm x 45 mm
Hex Head Bolt
(6 pcs)
H8 - 12 mm x 50 mm
Hex Head Bolt
(4 pcs)
H4 - 8 mm x 70 mm
Hex Head Bolt
(4 pcs)
H9 - 12 mm x 25 mm
Flat Washer
(4 pcs)
H10 - M12
Lock Washer
(4 pcs)
H11 - 12 mm Nut
(4 pcs)
P4 - Leg Support Brace
(4 pcs)
P5 - Leg Leveler
(4 pcs)
H7 - Plastic
Step Washer
(16 pcs)
FOR LEG LEVELER (To Scale)

- 4 -
PARTS REQUIRED
1 pc P1 Table Tennis Table Top and Frame Assembly
STEP 1:
IMPORTANT NOTE: Place table half top with playing surface face down on a CLEAN flat surface
for ease of correct assembly and to prevent any scratches or blemishes to the playing surface.
-
Lay one piece
Install P2 Legs using H2 Bolts with H7 Step Washers and H6 Nuts as shown in FIGURE 1..
Tighten, but do not overtighten on this step.
P1 Table Tennis Table Top and Frame Assembly flat with playing surface facing down as shown in FIGURE 1.
2 pcs P2 Leg-
4 pcs H2 8x40mm Hex Head Bolt-
4 pcs H6 8mm Nylon Lock Nut-
8 pcs H7 Plastic Step Washer-
FIGURE 1
STEP 2:
Install H8 Bolt with H10 Lock Washer, H9 Washer and H11 Nut onto P5 Leg Leveler
as shown in FIGURE 2. Tighten, but do not overtighten.
Repeat procedure for the other three P5 Leg Levelers.
H11
H10
H9
H8
P5
H2
H7
H7
H6
PARTS REQUIRED
4 pcs - P5 Leg Leveler
4 pcs - H8 12x50mm Hex Head Bolt
4 pcs - H9 12mm Flat Washer
4 pcs - H10 M12 Lock Washer
4 pcs - H11 12mm Nut
FIGURE 2
P2
P1
C1
IMPORTANT NOTE!
Metal Badge in here.
This end is the front
of the table.
IMPORTANT NOTE!
This end is the middle
of the table.

- 5 -
PARTS REQUIRED
1 pc P3 Leg Support Tube
STEP 3:
-
Install P3 Tube using H3 Bolts with H5 Flat Washers as shown in FIGURE 3. Tighten, but do not overtighten on this step.
Thread P5 Leg Levelers assembly from STEP 2 onto the P2 Legs as shown in FIGURE 3.
2 pcs H3 8x45mm Hex Head Bolt- 2 pcs H5 Flat Washer-
FIGURE 3
H3
H5
H5
H3
P3
P5
PARTS REQUIRED
1 pc P4 Leg Support Brace
STEP 4:
-
Install P4 Leg Support Brace using H4 Bolts with H5 Flat Washers and H6 Lock Nuts as shown in FIGURE 4.
Install P4 Leg Support Brace using H3 Bolt with H5 Flat Washers and H6 Lock Nut as shown in FIGURE 4.
Tighten, but do not overtighten on this step.
REPEAT PROCEDURE FROM STEP 1 TO STEP 4 FOR OTHER HALF TABLE TOP.
1 pc H3 8x45mm Hex Head Bolt- 6 pcs H5 Flat Washer-
2 pcs H4 8x70mm Hex Head Bolt- 3 pcs H6 Lock Nut-
FIGURE 4
H4
H5
H6
P4
P4
H3
H5
H5
H6
P2

- 6 -
PARTS REQUIRED
8 pcs H1 8x20mm Hex Head Bolt
STEP 5:
-
Connect two Half Table Top using H1 Bolts with H5 Flat Washers and H6 Lock Nuts as shown in FIGURE 5 and DETAIL A.
Tighten All Hardware on this step.
16 pcs H5 Flat Washer- 8 pcs H6 Lock Nut-
FIGURE 5
DETAIL A
H6
H5
H5
H1
WARNING:
THIS STEP REQUIRES FOUR OR MORE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON
ITS LEGS. BE CAREFUL, THE TABLE IS VERY HEAVY.
CAUTION:
DO NOT CLIMB, STAND OR JUMP ON TABLE!
SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY!

- 7 -
H1 T8755SY-H1 tloBdaeHxeHmm02xmm8 8
H2 T8755SY-H2 tloBdaeHxeHmm04xmm8 8
H3 T8755SY-H3 8 mm x 45 mm Hex Head Bolt 6
H4 T8755SY-H4 8 mm x 70 mm Hex Head Bolt 4
H5 T8755SY-H5 8 mm x 20 mm Flat Washer 32
H6 T8755SY-H6 8 mm Nylon Lock Nut
12 mm x 50 mm Hex Head Bolt
22
H7 T8755SY-H7 Plastic Step Washer
12 mm x 25 mm Flat Washer
16
H8 T8755SY-H8 4
H9 T8755SY-H9 4
H10 T8755SY-H10 M12 Lock Washer 4
H11 T8755SY-H11 tuNmm21 4
P1 T8755SY-P1 Table Tennis Table Top Frame Assembly 2
P2 T8755SY-P2 Leg 4
P3 T8755SY-P3 Leg Support Tube 2
P4 T8755SY-P4 Leg Support Brace
Net Post
4
P5 T8755SY-P5 Leg Leveler
Net
4
P6 T8755SY-P6 2
P7 T8755SY-P7 1
C1 T8755SY-C1 Steel Bracket (Pre-installed) 8
M1 T8755SY-M1 Owner’s Manual 1
K1 T8755SY-K1 Hardware Kit 1

3 YEARS LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the “Product”).
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
three (3) years from the original purchase.
WARRANTY PERFORMANCE: During the above three (3) years warranty period, ESCALADE SPORTS shall
repair or replace with a comparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our
satisfaction to be thus defective, please contact our Warranty Dept.
R
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED
BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
R
WORKMANSHIP.
R
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Produts. ESCALADE SPORTS strongly recommends that the Product is insured for value prior to mailing.
R
R
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE ABOVE THREE (3) YEARS WARRANTY PERIOD. ESCALADE SPORTS SHALL
NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
R
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty give you specific legal rights and you may also have other rights which
may vary from state to state.