stilum Tamino 1 User guide

State: 19.09.2017 p. 1
Mounting instruction climbing equipment „Tamino 1“
Item-No. 51 5559 601
© stilum GmbH, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
balance board
double bow
hexagons
slide climbing net
ladder bow
Diagram 1: Overall view of play equipment with description of individual elements

State: 19.09.2017 p. 2
Mounting instruction climbing equipment „Tamino 1“
Item-No. 51 5559 601
© stilum GmbH, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
1. Select the play equipment location in consideration of the required safety
area (see Diagram 4: 6400 x 7700 mm).
2. Carry out excavation work for 9 foundations as shown in Diagram 2a and 2b.
After excavation, compress the foundation oor.
Note: The combination equipment is built in on the play level. Pay attention
to items marked „game level” of play equipment!
3. Setup the main foundation (T-form: LxWxH 1000x1353x300mm), and the
foundation for the double bow and the ladder bow (LxWxH 600 x 600 x
300mm), the foundation for the climbing net (1100 x 300 x 300mm), the foun-
dation of the slide (800 x 600 x 300mm) and the four other foundations acc.
to the dimensions indicated in diagram 2a and 2b the quality class C 20/25
with horizontal reinforcement.
4. After a setting period of 10-14 days, depending on weather conditions and
foundation size - clean the surface of the foundations and start with the instal-
lation of the combination equipment.
Diagram 2: Side view with dimensions „Tamino 1“
300
2418
450 857
1865
A A
600
1000
1000
250
353
500
600
600
600
600
600
300
1100
100
750
1489
800
600
3980
4338
1701
1398
1953
2255
981
463
30
430
2988
2825
2725
2562
2426
2263
1007
1362
1940
2422
2999
488
1109
1627
1730
1428
676
525
1230
A-A (1 : 25)
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
Tamino 1
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Gewicht
Name
Name
Fundamentplan
1013-00-00
10356.9 Maßstab
Behnke 14.06.17
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
Legende
Reinforcement plan:
Concrete foundation with reinforcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C 20/25
Foundations for attachment parts are no-reinforced
450
299
535
1848
2401
1466
4170
532
272
885
298
1430
15°
30°
826
2155
185
784
2980
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
2
Tamino 1
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:25
A3
Gewicht
Name
Name
Übersicht
1013-00-00
650.2 Maßstab
Behnke 02.06.17
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Diagram 3: Position of the elements „Tamino 1“

State: 19.09.2017 p. 3
Mounting instruction climbing equipment „Tamino 1“
Item-No. 51 5559 601
© stilum GmbH, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
5. Place the head of the catarpillar as described in diagramm 1 and 3
onto the foundation.
Note: Do not screw the base plates onto the foundations yet!
6. Place the balance board and the other hexagons according to the
postitions in diagram 3.
7. Add the addition parts (double bow, slide, ladder bow and climbing
net) as shown in diagram 2b and connect it with the screws inclu-
ded in the delivery.
8. Align the play equipment once more on the foundations.
Note: Avoid sagging of the climbing net.
9. Drill holes into all foundations and screw the play equipment into
the foundations with the included heavy-duty dowels.
10. Fill up and compress the holes between the foundation and the
foundation hole with the excavation.
Diagram 2b: Position of the foundations
A A
600
1000
1000
250
353
500
600
600
600
600
600
300
1100
100
750
1489
800
600
3980
4338
1701
1398
1953
2255
981
463
30
430
2988 2825
2725
2562
2426
2263
1007
1362
1940
2422
2999
488
1109
1627
1730
1428
676
525
1230
A-A (1 : 25)
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
2
Tamino 1
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Gewicht
Name
Name
Fundamentplan
1013-00-00
10356.9 Maßstab
Behnke 14.06.17
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
Legende
slide
Main found-
ation
climbing
net
ladder bow
Climbing
bow

State: 19.09.2017 p. 4
Mounting instruction climbing equipment „Tamino 1“
Item-No. 51 5559 601
© stilum GmbH, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
11. Seal the foundation with the safety cover required for the height of fall
indicated.
Critical drop height: 800 mm.
Recommended surface material: grass, sand, wood chip, gravel,
synth. fall protection.
12. Do not allow children to use the equipment before the installation has
been nished.
13. After 3 months, check the screws at the joints and retighten them if
necessary.
Attention: If the play equipment has been incompletely installed or partly
dismantled when carrying out maintenance and repair work, this may
lead to
particular risks of injury for the user. For this reason, make clearly visible
that the equipment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless
steel should not come with „normal“ steel parts in contact. Those steel
parts may rub off and leave small steel particles in combination with
moisture brown rust stains. If such corrosion occur on stainless steel
parts, they are ne to remove with an abrasive (240 grit).
Please take care when transporting and setting up the fact that the com-
ponents are made of stainless steel with no „normal“ steel parts in contact.
With every playground equipment with wooden parts might occur desica-
tion cracks caused by the weather. These desication cracks are admissi-
bly according to the EN 1176 Bbl 1:2009-1, 4.2.7.6.
6400
R1500
R
1500
1760
1545
R
1500
R
2320
7700
1985
1415
1640
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
Tamino 1
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:40
A3
Gewicht
Name
Name
Draufsicht
1013-00-00
526.3 Maßstab
Behnke 13.06.17
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Diagram 4: Top view with the minimum space „Tamino 1“

State: 19.09.2017 p. 5
Mounting instruction climbing equipment „Tamino 1“
Item-No. 51 5559 601
© stilum GmbH, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved
In order to preserve a good visual appearance of your stilum playground equipment
over a long period one should take care of maintenance of the stainless surface
even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently cleaned
from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application time.
During cleaning with mild abrasive components, only wipe over stainless steel sur-
face in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on cars)
or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl alcohol,
isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the surface
again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type and
degree of soiling as well as on demands made on optical characteristics. Therefore
cleaning is advisable at intervals of six to twelve months – whereby in the case of
strong soiling it is appropriate to clean the playground equipment at intervals of 3 to
six months.
MAINTENANCE OF WOODEN ELEMENTS
To ensure a long life of stilum playground equipment, wooden surfaces should be
regularly re-glazed. This provides the wooden surfaces with the necessary protec-
tion and preserves the look. Areas which are not exposed to rain should be regular-
ly freed from deposits.
The cleaning intervals depend on the degree and type of soiling as well as on the
exigencies on cleanliness. It is recommended to clean and / or glaze at every 6
to 12 months, or to shorten the cleaning interval to 3 to 6 months if the wheather
conditions are bad.
LASUR APPLICATION
Use a soft and at brush or / and a glaze application roll to paint.
The wood should be cleaned a few hours before glazing. That can be done with
mild javel water, which should in any case be rubbed off afterwards. For resistant
dirt use a wood cleaner. Eventually a light abrasion is necessary. If water-based de-
tergents are used for cleaning, please ensure that the wood elements are thorough-
ly dried before the glazing is done.
Always brush in one direction, so that the glaze can spread evenly. Apply very
thinly!
Remove glaze with a soft cotton cloth.
Then let the freshly glazed wood dry for at least one day and prohibit the use of the
equipment for this duration.