stilum supra 2 Robinia User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 13.08.2019 p. 1
Mounting instructions for horizontal bar „supra 2“ Robinia
Item No. 55 1515 601
Diagram 1: Overall view of „supra 2“ Robinia

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 13.08.2019 p. 2
Mounting instructions for horizontal bar „supra 2“ Robinia
Item No. 55 1515 601
1. Select the play equipment location in consideration of the required safety
area (see diagram 4: 3000 x 3000mm).
2. Carry out excavation work for the foundations as shown in diagram 2. After
excavation, compress the foundation oor.
Note: The horizontal bar is built in on the play level. Pay attention to items
marked „play level“ of play equipment!
3. Set up the three concrete foundations acc. to the dimensions indicated in
diagram 2 with central, horizontal reinforcement.
4. After a setting period of 10 - 14 days, depending on weather conditions and
foundation size - clean the surface of the foundations and start with the instal-
lation of the play equipment.
5. Fix the horizontal bars as shown in diagram 3 with the screws and nuts inclu-
ded in the delivery.
6. Place the pre-assemled horizontal bar on the foundation and screw it with the
heavy-duty dowels included in the delivery.
7. Fill up and compress the holes between the foundation and the foundation
hole with the excavation.
8. Seal the whole minimum zone/safety area with the impact protection required
for the fall heights indicated. Set up impact-absorbing playground surfacing
according to EN 1176-1.
Critical drop height: 1350mm
Recommended surface material: synth. fall protection.
9. Do not allow children to use the equipment before the installation has been
nished.
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
supra 1 Robinie_150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:15
A3
Gewicht
Name
Name
Übersicht
2109-00-00
76606.9 Maßstab
x xx.xx.xx
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
supra 1 Robinie_150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:15
A3
Gewicht
Name
Name
Übersicht
2109-00-00
76606.9 Maßstab
x xx.xx.xx
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Diagram 2: Side view with dimension details „supra 2“ Robinia
Diagram 3: Assembly
Reinforcement plan: Concrete foundation with reinforcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C20/25
400
700 700 700
753 753
550
Erde
Ground
Füllmaterial
Filling
Beton
Concrete
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
supra2 Robinie_150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:25
A3
Gewicht
Name
Name
Fundament
2111-00-00
4717110.8 Maßstab
Schramm 07.03.17
700 700753
400
550
700
Beton
Concrete
Füllmaterial
Filling
Erde
Ground
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
supra 1 Robinie_150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Gewicht
Name
Name
Fundament
2109-00-00
3134522.7 Maßstab
Schramm 07.03.17

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 13.08.2019 p. 3
Mounting instructions for horizontal bar „supra 2“ Robinia
Item No. 55 1515 601
Diagram 4: Top view
Extent of the minimum
zone = safety area
3000
3000
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach
DIN ISO 1302
Reihe 2
Zul. Abweichung
DIN 2768 - mH
1
supra2 Robinie_150
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:25
A3
Gewicht
Name
Name
Draufsicht
2111-00-00
98.7 Maßstab
Schramm 07.03.17
A Fallraum kleiner 14.02.19 ES
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to par-
ticular risks of injury for the user. For this reason, make clearly visible that the
equipment shall not be used in such cases.
STAINLESS STEEL
NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may rub
off and leave small steel particles in combination with moisture brown rust stains.
MAINTENANCE: If such corrosion occur on stainless steel parts, they are ne to
remove with an abrasive (240 grit).
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 13.08.2019 p. 4
Mounting instructions for horizontal bar „supra 2“ Robinia
Item No. 55 1515 601
LASUR: Use a soft and at brush or / and a glaze application roll to paint.
The wood should be cleaned a few hours before glazing. That can be done with
mild javel water, which should in any case be rubbed off afterwards. For resistant
dirt use a wood cleaner. Eventually a light abrasion is necessary. If water-based de-
tergents are used for cleaning, please ensure that the wood elements are thorough-
ly dried before the glazing is done.
Always brush in one direction, so that the glaze can spread evenly. Apply very
thinly!
Remove glaze with a soft cotton cloth.
Then let the freshly glazed wood dry for at least one day and prohibit the use of the
equipment for this duration.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type and
degree of soiling as well as on demands made on optical characteristics. Therefore
cleaning is advisable at intervals of six to twelve months – whereby in the case of
strong soiling it is appropriate to clean the playground equipment at intervals of three
to six months.
WOOD
NOTE: For all play equipment with wooden elements, it cannot be ruled out that dry
cracks may develop. These natural changes of wood are dependent on climate con-
ditions as well as on the age and usage of the play equipment. Longer dry periods
may lead to more dry cracks.
This development, however, does not represent a quality defect. Static properties of
the equipment are not impaired.
See EN 1176 Bbl 1:2019-01 4.2.7.6: Dry cracks in wood elements as a consequence
of weather conditions are not to be considered as dangerous openings in terms
of the standard due to the fact that the shape of the cracks (tapering towards the
inside) makes it almost impossible for ngers to get trapped in them.
MAINTENANCE: To ensure a long life of stilum playground equipment, wooden
surfaces should be regularly re-glazed. This provides the wooden surfaces with the
necessary protection and preserves the look. Areas which are not exposed to rain
should be regularly freed from deposits.
The cleaning intervals depend on the degree and type of soiling as well as on the
exigencies on cleanliness. It is recommended to clean and / or glaze at every 6 to 12
months, or to shorten the cleaning interval to 3 to 6 months if the wheather condi-
tions are bad.