stilum tollo User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 25.09.2015 · S. 1
Mounting instructions for digger „tollo“
Item-No. 511100401
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 25.09.2015 · S. 2
Mounting instructions for digger „tollo“
Item-No. 511100401
400
450
345
785
1215
30°
155°
350
Schaukelauslenkung mit
maximalem und minimalem Winkel
Erde
Ground
Füllmaterial
Filling
Beton
Concrete
Sand
Sand
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.

WERKSTOFF / ROHMAß:
MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
WERKSTUECKKANTEN
NACH DIN 6784
+0,3
-0,3
FREIG:
GEPR:
GEZ:
DATUM: NAME:
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
BENENNUNG:
BESTELL-NR:
ZG-NR:
29.10.2012
Rev.:
KUNDE:
A4
Wiebe Tollo Fundament
Diagram 2: Side view with dimension details „tollo“
400
450
345
785
1215
30°
155°
350
Schaukelauslenkung mit
maximalem und minimalem Winkel
Erde
Ground
Füllmaterial
Filling
Beton
Concrete
Sand
Sand
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.

WERKSTOFF / ROHMAß:
MAßSTAB:
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
ZUL. ABWEICHUNG
DIN 2768 - mH
WERKSTUECKKANTEN
NACH DIN 6784
+0,3
-0,3
FREIG:
GEPR:
GEZ:
DATUM: NAME:
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
BENENNUNG:
BESTELL-NR:
ZG-NR:
29.10.2012
Rev.:
KUNDE:
A4
Wiebe Tollo Fundament
1. Select the play equipment location in consideration of the required safety
area (see Diagram 3: Ø 5500 mm).
2. The impact area of a playground equipment with an enforced movement is
not allowed to overlap the impact area of other equipment.
Regarding to DIN 1176 - 4.2.8.2.5, impact absorbing surfaces have to be put
under the whole impact area of every equipment with an enforced movement.
3. Carry out excavation work for the foundation anchor as shown in Diagram 2.
After excavation, compress the foundation oor. Note: The play equipment is
built in on the play level.
4. Set up the concrete foundation acc. to the dimensions (400mm x 400mm x
350mm) indicated with central, horizontal reinforcement.
5. During the setting period of 10 -14 days - depending on weather conditions
and foundation size - do not allow to use the equipment.
swing displacement with
minimal and maximal angle
Reinforcement plan: Concrete foundation with rein-
forcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class B25

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 25.09.2015 · S. 3
Mounting instructions for digger „tollo“
Item-No. 511100401
6. After the setting clean the surface of the foundation, place the pre-mounted
play equipment onto it and screw the base plate onto the foundation anchor
with the included heavy-duty dowel M10.
7. Seal the foundation with the safety cover required for the height of fall indi-
cated (critical drop height ≤ 1000 mm). Set up impact-absorbing playground
surfacing according to EN 1176-1, table 4. Recommended surface material:
sand.
8. Do not allow to use the equipment before the installation has been nished.
9. Attention: If the play equipment has been incompletely installed or partly
dismantled when carrying out maintenance and repair work, this may lead to
particular risks of injury for the user. For this reason, make clearly visible that
the equipment shall not be used in such cases.
10. NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may
rub off and leave small steel particles in combination with moisture brown rust
stains.If such corrosion occur on stainless steel parts, they are ne with an
abrasive (240 grit) to remove.
Please take care when transporting and setting up the fact that the compo-
nents are made of stainless steel with no „normal“ steel parts in contact.
Diagram 3: Top view „tollo“
2420
1500
5420
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
MAßSTAB:
Rev.:
KUNDE:
BESTELL-NR:
ZG-NR:
BENENNUNG:
FREIG:
GEPR:
GEZ:
NAME:
DATUM:
WERKSTOFF / ROHMAß:

ZUL. ABWEICHUNG
DIN 2768 - mH
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
WERKSTUECKKANTEN
NACH DIN 6784
-0,3
+0,3
29.10.2012
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A4
Tollo Mindestraum
Wiebe
Extent of the
minimum zone
= safety area

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved. State: 25.09.2015 · S. 4
Mounting instructions for digger „tollo“
Item-No. 511100401
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the playground equipment at
intervals of 3 to six months.