Stinger MT Series User manual

MT SERIES MT-700.1
MT-1000.1
MT-1500.1
MT-2000.1
Installation Guide
Specifications
MONOBLOCK AMPLIFIERS
®

Signal Connections
Power Connections
Remote Turn-On from head unit
or line output converter (LOC)
RCA Line Out from head unit
or line output converter (LOC)
Adjust bass level
remotely from the
driver’s seat.
An external fuse must be
added to the Positive (+)
wire. Refer to the Specs
for the correct size fuse.

Amplifier Controls
1
52 63 74 8 9
1. Protect LED [PRT]
Red when amplier is
powering up or in Protection
Mode. See Troubleshooting
for more information.
Power LED [PWR]
Blue when amplier is ON.
2. REMOTE
Connect the SA1RBC Remote
Bass Control knob here.
3. INPUT
Connect to line level output
RCAs from head unit or line
output converter (LOC).
4. BRIDGE
Used to connect two
ampliers together. See
page 8.
5. GAIN
Used to adjust the input
sensitivity to match the
input level signal.
6. Low Pass Filter [LPF]
A low pass crossover for the
subwoofer output. Variable
from 40Hz to 180Hz.Generally
set around 80Hz.
7. SUBSONIC
A high pass crossover for the
subwoofer output. Variable
from OFF to 50Hz. Generally
set between 30-35Hz.
8. Boost Frequency [FREQ]
Selects the frequency to boost
when adding BOOST. Variable
from 30Hz to 80Hz.
9. BOOST
Boosts the selected frequency
[FREQ] from 0dB to 12dB.

MT-2000.1 Specs
1Ω2000W X 1
2Ω1500W X 1
4Ω800W X 1
Bridged RMS Rating / 2Ω Minimum 3800W x 1
Signal to Noise (@ CEA Standard) -93dB
Input Sensitivity 0.2-6v
Gain 0.2v - 6v
Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic)
LP 40Hz - 180Hz @ 12dB/Oct
Bass-Boost Frequency Range 30-80 Hz
Bass-Boost Q 0-12dB
Frequency Response(+- 1dB) 10Hz - 180Hz
Efciency (Average) 80%
Topology Class Class D
Remote Bass Control Yep (Included)
Operating Voltage 9V to 16V
Power Terminal 0/1 Gauge
Speaker Terminal 8 Gauge
Recommended External Fusing 200A
RMS Power Ratings listed at less than 1% THD @ 14.4v

MT-1500.1 Specs
1Ω1500W X 1
2Ω1000W X 1
4Ω550W X 1
Bridged RMS Rating / 2Ω Minimum 2800W x 1
Signal to Noise (@ CEA Standard) -93dB
Input Sensitivity 0.2-6v
Gain 0.2v - 6v
Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic)
LP 40Hz - 180Hz @ 12dB/Oct
Bass-Boost Frequency Range 30-80 Hz
Bass-Boost Q 0-12dB
Frequency Response(+- 1dB) 10Hz - 180Hz
Efciency (Average) 82%
Topology Class Class D
Remote Bass Control Yep (Included)
Operating Voltage 9V to 16V
Power Terminal 4 Gauge
Speaker Terminal 8 Gauge
Recommended External Fusing 150A
RMS Power Ratings listed at less than 1% THD @ 14.4v

MT-1000.1 Specs
1Ω1000W X 1
2Ω700W X 1
4Ω400W X 1
Bridged RMS Rating / 2Ω Minimum 1800W x 1
Signal to Noise (@ CEA Standard) -93dB
Input Sensitivity 0.2-6v
Gain 0.2v - 6v
Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic)
LP 40Hz - 180Hz @ 12dB/Oct
Bass-Boost Frequency Range 30-80 Hz
Bass-Boost Q 0-12dB
Frequency Response(+- 1dB) 10Hz - 180Hz
Efciency (Average) 82%
Topology Class Class D
Remote Bass Control Yep (Included)
Operating Voltage 9V to 16V
Power Terminal 4 Gauge
Speaker Terminal 8 Gauge
Recommended External Fusing 100A
RMS Power Ratings listed at less than 1% THD @ 14.4v

MT-700.1 Specs
1Ω700W X 1
2Ω500W X 1
4Ω300W X 1
Bridged RMS Rating / 2Ω Minimum 1200W x 1
Signal to Noise (@ CEA Standard) -93dB
Input Sensitivity 0.2-6v
Gain 0.2v - 6v
Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic)
LP 40Hz - 180Hz @ 12dB/Oct
Bass-Boost Frequency Range 30-80 Hz
Bass-Boost Q 0-12dB
Frequency Response(+- 1dB) 10Hz - 180Hz
Efciency (Average) 85%
Topology Class Class D
Remote Bass Control Yep (Included)
Operating Voltage 9V to 16V
Power Terminal 4 Gauge
Speaker Terminal 8 Gauge
Recommended External Fusing 80A
RMS Power Ratings listed at less than 1% THD @ 14.4v

Bridging (Connecting) Two Amplifiers
LIMITED WARRANTY
Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from
the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an
authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for
any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective
product with new or remanufactured product at no charge. Damage caused by the following is not covered under war-
ranty: accident, misuse, abuse, product modication or neglect, failure to follow installation instructions, unauthorized
repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear
and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger
reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that
country’s reseller for information.
Stinger is a Power Brand of AAMP Global
15500 Lightwave, Clearwater, Florida 33760
© 2022 AAMP Global
MCAMP-IG REV 102622
Connect Bridge Out on the Primary amplier to Bridge In on the Secondary amplier.
Connect the Negative speaker output on the Primary amplier to the Negative speaker output
on the Secondary amplier. Connect the Positive speaker output of the Primary amplier to the
positive speaker terminal. Connect the Positive speaker out put of the Secondary amplier to the
negative speaker terminal. 2 ohm minimum! All adjustments are made on the Primary amplifier.
STOP! Please DO NOT return to seller
For help with installation, replacement parts, warranty or returns, please
contact us directly at 727-732-3114 or [e-mail]
®