store away Winsford User manual

Winsfordstore
away
Assembly Instructions
revised 0221 - 1.0

We advise that you unpack the boxes in the order shown in
these instrucons and follow the assembly instrucons carefully.
Please be careful during construcon as secon of the cupboard
may be unstable unl construcon is complete.
Your hardware pack should contain the following:
CODE DESCRIPTION QTY PICTURE
CB1 Connnecting
Bolt 24
CL1 Connecting
Lock 24
AB1 Angle
Bracket
SP3Shelf Peg
(lock) 32
HANDLE2 Bow Handle 2
S30 Handle Screw 4
H3 Desk Hinge2
35-15S Screw 12
C2 Castor Black 4
C3 Castor Black
with Brake 2
35-17S Caster Screw 44
C4 Leg Caster 2
AXI-HINGE-M Axi Hinge Male
Part 4
4

STEP 1
You will need to open box -
screw in to
this point
CB1
Screw CB1 Bolts into all
the holes marked with
a red circle
Insert CL1 Locks into
the holes as indicated
with a blue circle
WINS-SD&CD
Attach hinges
AXI-HINGE-M
using pre tted
screws and
35-15S as
shown
Attach angle brackets as shown using
screws 35-17S
WINS-LHS WINS-RHS

Insert CL1 Locks into
the holes as indicated
with a blue circle
WINS-BASE
STEP 2
You will need to open box -
WINS-TDB
Front Edge
Attach castors C2
with screws 35-17S as shown
to holes marked with red circles
Attach castors with brakes C3
with screws 35-17S as shown
to holes marked with green circles

WINS-MB1
WINS-MB1
WINS-BASE
WINS-LHS
STEP 3
You will need to open box -
WINS-BACK
WINS-MB1
X 2
Insert CL1 Locks into
the holes as indicated
with a blue circle
STEP 4
Attach the Base to the left hand side by slotting the panel onto the connecting bolts and
tightening the connecting locks in the base. Then secure the base to the sides using the
angle brackets you have already attached to the sides (using screws 35-17S).
Then x the two MB1 backs to the left hand side as shown below. You can choose to have
the connecting locks showing on the inside of the unit or the outside by rotating the panels.

STEP 5
Attach the RHS to the section you have already constructed, tighten all of the connecting
locks and secure the base to the right hand side with the angle brackets as in step 4.

STEP 6
Attach the WINS-CD to the base of the section you have already constructed. Screw CB1
connecting bolts into the two holes in the base and then secure with CL1 connecting locks
in the WINS-CD.
It is important to ensure you have the WINS-CD panel the correct way up. You will see a label
which states TOP on this panel and this should be at the top when tted.

STEP 7
Attach the WINS-TOP to the the section you have already constructed as shown below.
Screw CB1 connecting bolts into the six holes in TOP panel and then secure with CL1
connecting locks in the WINS-CD and the left and right hand sides.

Below you will see the placement for all for all of the shelves.
To t the shelves insert shelf pegs SP3 into the holes for each shelf. Ensure that the at
surface of the peg is facing up. Once the shelf has been placed onto the pegs tap the centre
of the shelf with your hand to lock the shelf onto the grips on the peg. This will stop the shelf
sliding when taking storage containers out of the unit.
STEP 8
You will need to open box -
WINS-SH
Insert this way up
Place all shelves
onto shelf pegs
and tap down
onto centre of
shelves
with your hand
to lock onto
pegs to prevent
shelf sliding

STEP 9
Take your two doors and insert caster C4 into the pretted bracket on the bottom
of each door. Fit the two handles using the screws provided.
Then t your doors by inserting the metal bracket which you have already xed to each side
into the receiving part which is pre tted to the door and then tighten the locking screw.
You may nd it easier to do this if you loosen the locking screw a little before insert the
hinge bracket. At this point ensure the wheel as at the botttom of the door and the handle
at the top.

STEP 10
Position you doors so that they are open no more than 90 degrees so that they will support
you desk panel.
Attach hinges H3 using screws 35-15S to the top (WINS-TOP). Then place
the desk on top of the doors and attach the hinges to the desk panel.

10L
BOX
The Storeaway Winsford unit is designed and manufactured in the UK by:
CRAFTS
storage
www.storage4crafts.co.uk
STEP 11
.Place your storage containers into you unit as shown below.
IMPORTANT SAFETY INFORMATION
When the desk is in use always ensure it is fully supported on the doors - they must
be open no more than 90 degrees.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO YOUR UNIT
AND /OR INJURY
5.5L
BOX
9L
BOX