Store More Sloped Shelf Shelving User manual

Assembly Guide
Sloped ShelfShelving
Hardware
Set-up
Overall Dimensions
All required hardware is included.
Please check the contents with your
packing slip.
Read instructions carefully.
Save this document for future reference.
Two people are required for the assembly.
The sloped shelves must not be used
with shelving over 99" in height or with
mezzanines.
Tools Required Outils requis
7/16"
Phillips #3
Chalk line
1/4-20 bolts
7/16"
1/4-20 bolts
5/8"
1/4-20 bolts
1"
1/4-20 nuts Nylon clip
Check the leveling of the floor in order to
determine the critical areas. Use floor
anchor plates and shim plates to level
the shelving units.
Make sure that no obstacle nor electrical
wiring comes in contact with the
structure.
Recommendation:
Plumbness:
The shelving must be installed with a
maximum tolerance from the vertical of
1/2" inch in 10 feet of height.
Floor plates must be anchored if more
than one shim is used.
Nominalwidth+ 1 5/8"
30", 36", 42", 48"
Nominal widths
1/16''
A
with back braces
It is recommended to lay out shelving
positions on the floor with a chalkline
before beginning the installation.
B*
nominal dimension real dim.
18", 24"
30, 36"
A
nominal
+ 1/4"
nominal
+ 1/2"
nominal
+ 9/16"
nominal
+ 9/16"
with back braces
with back panels
24"
30"
36"
48"
B *
Depths
1 5/8"
Some of the illustrated hardware is only supplied with optional components.
Shim
1/4-20 bolts
1x
5/8"
1/4-20 nuts
1x
Anchor
Plate
Cut-resistent gloves
3DJH
www.StoreMoreStore.com | 855-786-7667

11/2"
13 1/2"
7/16"
4 per brace
13 1/2" 13 1/2"
39" 51"to/à
75"to99"
Upright Assembly (bolted)
If using welded uprights, go directly to the next step.
Visual reference : Always try to align screws
with the double-holes on the front of the post. Up
Double holes
This endDOWN
Post Direction
3DJH
www.StoreMoreStore.com | 855-786-7667

2
Rod Cap
1
Tapping screw
1 2"/
Sloped shelf guides (optional)
Sloped shelf guides positions
Prei all guides beforenstall
installing shelves into the
shelving.
3
C/C = 1 1/2"
C/C = 1 1/2"
C/C - 7/16"
C/C = 2 1/4"
WiGth MaxNbofguides MaxNbofspaces
30" 19 18
36" 23 22
42" 27 26
48" 31 30
2 positions are possibles for the first
guide.The first position is designed to
clear the post of the shelf.
You can use the illustrations at the next page to calculate/draw the positions
of your shelve guides for your configuration.
3DJH
Top view
www.StoreMoreStore.com | 855-786-7667

Sloped shelf guides positions (continued...)
30" width= 19 guides
42" width= 27 guides
36" width= 23 guides
48" width= 31 guides
3DJH
Top view
www.StoreMoreStore.com | 855-786-7667

Anchoring and Leveling
Anchoring, base and shelves
If required, the front base must be installed
before the lower shelf is put in place.
Base
1
Clip non-mandatory
2
4"=18" deep
6"=24" deep
8"=30" deep
8"=36" deep
3
3 square hole from bottom
rd
3
Always start to install the shelves from the bottom
to the top of the shelving
Place left and right bracket for the
bottom shelf.
1
2
3
4Reinforcement
30 and 36" deep shelf
reinforcement. (optional)
4
3DJH
www.StoreMoreStore.com | 855-786-7667

Anchoring, base and shelves (continued..)
8Second shelf
Repeat step 3 to 7 for second shelf from the bottom of the shelving.
6
Lowerthefrontatfirst.
7
5
5
Distance between shelves
Possible shelf adjustment of 2" in height if use with
corner gussets.
2 3/8"
2 7/16"
C/C
C/C
C/C
C/C-2 3/8"
C/C-2 3/8" C/C-2 7/16"
C/C-2 7/16"
3DJH
www.StoreMoreStore.com | 855-786-7667

Anchoring, base and shelves (continued..)
A
B
D
F
G
C
E
H
Top shelf
Middle shelf
2nd shelf
Corner gussets:
For shelving without back sway brace or back panels,
3 kits of corner gussets must be installed. On the
second, the middle, and the top shelf.
Corner gussets
Positioning the shelf with corner gussets:
If the shelving uses corner gussets, the shelves
must be installed on the holes of the post
positioning at the same level as the front hole of
the post, to be able to screw the gusset on the
shelf.
Possible shelf adjustment of 2" in height with the
gussets
Same level Same level
Front hole
3DJH
www.StoreMoreStore.com | 855-786-7667

Use this gusset when the shelvings are assembly in continuously
Anchoring, base and shelves (continued..)
The corner gusset are not compatible with the back-to-back shelving installations.
4
4
1
1
2
1
3
1 1/4"
1 1/4"
2 or 4xx
4x
2 or 4xx
4x
2
3
3DJH
www.StoreMoreStore.com | 855-786-7667