Vivo STAND-V102M User manual

Single Monitor and Tablet Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102m
SKU: STAND-V102M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Clamp
C(x2)
Arm
J (x4)
Arm Cable Clip
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x2)
VESA Plate
E(x1)
Tablet Mount
F (x1)
Pole Cap
G(x1)
Grommet Plate
H (x1)
So Pad
I (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x6)
M4x16mm
Thumbscrew
S-B (x4)
M4 Washer
S-C (x2)
M6 Cap Nut
S-D (x3)
M6x16mm
Screw
TOOLS NEEDED
22lbs
Monitor
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
K (x1)
Pole Cable Clip
M-A (x8)
M4x12mm
Thumbscrew
M-B (x8)
M4x30mm
Screw
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
M-C (x8)
Spacer
5.5lbs
Tablet
(2.5kg)

3
ASSEMBLY STEPS
OPTION A: Clamp Installation
Assemble Clamp (B) to Pole (A) using M6x16mm
Screws (S-D) and 3mm Allen Wrench (T-A).
Tighten Clamp (B) to the desktop.
Loosen the knob on Clamp (B).
OPTION B: Grommet Base Installation
Remove the screw from Clamp (B) using a Phillips
screwdriver, and set aside Clamp Bolt (B2).
Assemble Grommet Plate (G) to Pole (A) using
M6x16mm Screws (S-D) and 3mm Allen Wrench
(T-A). Peel the protective lm o of So Pad (H)
and place onto Grommet Plate (G). If not using
an existing through-hole, using a 10mm (⅜”) drill
bit, drill through the desktop at least 2” away from
the edge. Mount the pole assembly to the desktop
using Clamp Bolt (B2) and Support Plate (I).
STEP 2
STEP 1
B
A
S-D
T-A
10-60mm
B
B2
G
A
S-D
T-A
H
I
Desktop with Existing
Through-Hole
B
B2

4
STEP 3
STEP 5
Slide the rst Arm (C) onto Pole (A) and tighten the screw on the back using 6mm Allen Wrench
(T-C).
STEP 4
Slide the second Arm (C) onto Pole (A) and tighten the screw on the back using 6mm Allen Wrench
(T-C). Attach Pole Cap (F) to the top of Pole (A).
Assemble Arm Cable Clips (J) to Arms (C). Attach Pole Cable Clip (K) to Pole (A).
J
C
KA
C
A
T-C
F
A
C
T-C

5
STEP 6
Attach VESA Plate (D) to the back of the monitor using M4x12mm Thumbscrews (M-A) or M4x30mm
Screws (M-B) and Spacers (M-C).
STEP 7
With the adjustment screw holes on top, assemble Tablet Mount (E) to VESA Plate (D) using M4x16mm
Thumbscrews (S-A) and M4 Washers (S-B). Loosely install remaining M4x16mm Thumbscrews (S-A)
into the top adjustment holes in Adapter (E).
E
Adjustment
Holes
S-A
S-B
D
D
M-A
M-B
M-C

6
STEP 10
STEP 8
To adjust Tablet Mount (E) to t the device, push device down onto springloaded tabs and position
device against the face of the adapter. With the adjustment screws still loose, center the device on the
adapter. Then tighten the adustment screws.
Assemble VESA Plates to Arms (C) and secure using M6 Cap Nuts (S-C).
STEP 9
To remove the device, while holding both sides of the device, pull down, tilt the device,
then li it out. Reinstall the device in reverse order.
1
2
Device
C
S-C
E
Adjustment
Screws

7
STEP 11
Adjust the tilt using 5mm Allen Wrench (T-B).
T-B

LAST UPDATED: 01/18/2022
REV1
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303