stoy 416285 User manual

TRICYCLE
ENG SE FI DK NO

Stoy is not just a great toy brand because
the name is a clever anagram for the
word toys. The Swedish toy brand is highly
appreciated for their way of unifying subtle
Scandinavian design with high quality in all
their products. Stoy has a broad range of
toys and oers everything from baby gyms
and walkers to the softest of soft toys,
the prettiest dolls and dollhouses, classic
wooden toys, beautiful vintage balance
bikes and cool cruiser bicycles. Explore a
world of Stoy for great sustainable toys
that your kids will love and designs so nice
you’ll treasure them as interior details.

ENG ENG
Warnings
Tools ans Parts
Instructions
Do not ride on highways.
Protective equipment should be worn. Not to be used in trac.
To be used under the direct supervision of an adult.
Caution! Adult assembly required. Package contains small parts that can be dangerous for
children under 3 years before assembling.
IMPORTANT! Save packaging for future reference.
MAX 25 KG
Handlebar
Wheels
Fork
Seat
Pedal-fender
Basket and Footrest
2 Plastic gaskets
Three screws
Two nut / two at nut
Four at gaskets
Four tapping screws
Assembling
Remove the front fender and front wheel fork. Put
the fender into the fork and shaft and insert it into
the forks hole.
There is one side with strengthen plastic, it should
be on the back, and push the mudguard front to
hear a Click sound, it will be locked.
Install the handlebar. Insert gasket into fork
shaft before installing handlebars.
Insert the handlebar into the fork shaft with
the gasket installed and align it with the screw
hole. Fix the screw and lower the cover. The
torque of the screw nut shall not be less than
18N.M.
Insert the two rear wheels into the left and
right sides of the frame. Align the screw
holes. Put the Screws into the hole and then
tighten it with tools. The torque of the screw
nut shall not be less than 18N.M
Take the frame out, align the pipe mouth of
the frame with the fork axle that has installed
the fender, and insert it vertically. Note: there
is a groove at the lower end of the z shaft sle-
eve, which needs to be aligned with the hook
piece of the front fork shaft, otherwise the
direction of the wheel cannot be controlled

ENG
Place the seat on the iron plate on which the
seat is mounted, the screws are aligned to
the screw holes in the middle of the frame.
Tighten the nut after locating. Note: there are
two screw holes on the frame, please choose
the appropriate one according to your baby’s
height. After installation, please x the sponge
back into the seat. The torque of the screw
nut shall not be less than 18 N.M.
Place the top attachment of the footrest
tight against the seat and then assemble the
bottom part so the tricycle frame is in the
middle. Make sure the screws are aligned in
the screwholes.
Tighten the nut with the wrench, use a
screwdriver to hold the screw in place.Make
sure that the position of the footrest is in no
way interfearing with stearing or touching the
mudguard before use.
You must adjust the distance between the saddle and the
handlebar to the distance you need before doing anything.
(picture 7, two sets of parallel adjustment holes)
Lubricate the parts to prolong their service life.
Please check the rmness of all screws and nuts after using
the new tricycle for one week to ensure the safety of use.
When installing, please carefully follow the instructions to
avoid unnecessary damage.
This product shall be assembled by adults.
Before use, please check whether all parts are in place safely
and securely.
Do not ride on rough roads.
Any use failure must be repaired by an adult.
This product is suitable from 18 months+.
General use, maintenance
and attention of tricycles

Designed in Sweden
Made in China for Scandinavian Kids Group
Box 29098, SE-10052,Stockholm, Sweden