STREET WISE SWPFTB10R User manual

1Full Press: When fully pressed, you will hear a clicking sound. Revised: 10-22-2014
SWPFTB10R
Instruction Manual
STOP. Before Proceeding, Please Read: This stun baton flashlight performs many functions and has built in safety features that can be
confusing if you do not take time to read these directions and familiarize yourself with it. The key to understanding how this unit operates is the
“Function-Select Button.” Each time this button is pressed, the function changes in the following order: Light, Stun, Off. To help you remember the
order, the corresponding symbol is shown below the Function-Select Button: for Light, for stun, and for off.
Inserting and Charging the Rechargeable Batteries
1. We recommend fully charging the rechargeable batteries before inserting them into the unit. To do so, insert both 18650 4000mAh 3.7V li-ion batteries
(included) into the charging port according to the polarity diagram shown on the port. If the batteries are inserted correctly a red light will illuminate on the
charging port. Next, plug the slide-out plug into a standard wall outlet. When plugged into a standard wall outlet, a red light on the wall charger will come
on while the batteries are charging and change to green when completely charged. IMPORTANT: Do not charge for more than 8 hours at a time.
Overcharging can damage the batteries and void the warranty. If the flashlight becomes dim or if the electrical stun current becomes noticeably weaker,
the batteries will need to be charged. When not in use, charge the batteries every 60 days to ensure the unit will function optimally when needed.
2. To insert the batteries into the stun baton, unscrew the end cap by turning it in a counterclockwise direction (See above diagram for location to unscrew).
3. Insert the batteries according to the polarity diagram below. IMPORTANT: Batteries must be inserted as shown below. Inserting the batteries incorrectly
could damage the unit and void the warranty. Replace the end cap by turning in a clockwise direction until snug. Do not over tighten.
Using the Flashlight
Overview: This unit features three (3) light strengths (Maximum, Medium, & Low) and two light patters (SOS & Strobe). When the situation does not require
maximum light strength, the lower light settings can be used to extend the battery life.
1. Be sure the unit is set to Light Function (remember there are three (3) functions in the following order: Light, Stun, & Off)
2. Press the Function-Select Button until you see the light turn on. Note: If you press it more than three times and still do not see the light, fully press1the
Push-Button Tail Switch. In the Light function, this button will turn the light on and off (full press1) or change the light mode (half press).
3. Once the light is on you can change the light mode by either half pressing either the Function-Select Button or the Push-Button Tail Switch.
4. To turn off the light, fully press1either the Function-Select Button or the Push-Button Tail Switch.
5. If you turn the light off by fully pressing1the Push-Button Tail Switch, you will need to press this same button again to turn it on. If you turn it off by fully
pressing1the Function-Select Button be careful to note that you are now in stun function and pressing the Stun Activation Button will activate the stun
feature. To return to light function, you will need to press the Function-Select Button two (2) more times. Remember the order of the functions: When set to
Light Function, pressing once moves the function to Stun, pressing twice moves it to Off and pressing a third time moves it back to Light.
Testing the Stun Baton (WARNING: Do not test fire the stun baton for more than 1 second as this will damage the unit and void the warranty.)
1. First, you need to be sure the unit is set to Stun Function (Remember there are three functions- Light, Stun, & Off)
2. The easiest way to locate the Stun Function is to fully press1the Function-Select Button until you see the light turn on. Note: If you press it more than three
(3) times and still do not see the light, fully press1the Push-Button Tail Switch. Remember, if this button was pressed, the safety is ON and all of the
features are disabled until this button is pressed again.
3. Once the light is on, press the Function-Select Button once more. The unit is now in Stun Function.
CREE LED Flashlight
Triple Stun
Contact Probes
Stun Activation Button
Function-Select Button
(Light, Stun, Off)
Push-Button Tail Switch (Not Shown):
oFull Press1turns unit On/Off.
oHalf Press changes light mode.
Unscrew Here to
Insert Batteries
Negative ( - )
Positive ( + )
End Cap

1Full Press: When fully pressed, you will hear a clicking sound. Revised: 10-22-2014
4. Press the Stun Activation Button to test fire the unit. Do not hold the button down for more than 1 second. You will see and hear an electrical charge fire
across the top of the unit between the contact probes.
5. Once your test is complete, fully press1either the Push-Button Tail Switch or the Function-Select Button.
6. If you pressed the Push-Button Tail Switch, then the safety is on and you will need to press this same button again before any of the functions will operate.
Warning: Once you press this button again the safety will be off and ready to stun as soon as the Stun Activation Button is pressed again.
7. If you fully pressed1the Function-Select Button, the unit will be in the OFF position. Remember the order of the icons: Light, Stun, & Off. Press this button
once more for the light or two times to return to the Stun position.
Using the Stun Baton in Self Defense
1. Before using the stun baton in self-defense, we recommend you become familiar with how this unit operates so you can quickly
protect yourself with the Stun Function. See How to Quickly Access the Stun Function below.
2. Using the directions above, move the unit into the Stun Function Mode.
3. Touch your assailant’s body with the contact probes and press the Stun Activation Button.
4. Touching anywhere on the assailant’s body will have an effect. However, the maximum effect is achieved in the areas shown to
the right:
5. When touching the assailant’s body, you will not see or hear the electrical charge as you do when the unit is test fired. You can
hold the Stun Activation Button down for more than 1 second, as this will not damage the unit, as it will when being test fired.
6. You do not have to be concerned about the effects of the charge being transferred to you. Even if the assailant touches you while
being stunned, you will not feel the effects of the charge.
How to Quickly Access the Stun Function
1. When the Flashlight is on, fully press1the Function-Select Button then press the Stun Activation Button.
2. When the flashlight is not in use, we recommend leaving the Function-Select Button in the Stun position then fully pressing1the Push Button Tail Switch to
turn on the safety. You do this by locating the light and fully pressing1the Function-Select Button once more. This turns the unit OFF. When you want to
quickly use the Stun Function, push the Push-Button Tail Switch then the Stun Activation Button.
Important: Under normal circumstances, you can access the Stun Function by pressing the Function-Select Button until
you see the light then press it once more for the Stun Function. Remember, if you press it more than three (3) times and
do not see the light, the safety is on and none of the functions will work. Press the Push-Button Tail Switch to turn off the
Safety. However, in a panic situation when you need to quickly defend yourself, you will not have time to press all those
buttons. Therefore, when you are not using the flashlight, we recommend leaving the unit in position described in #2 in
the How to Quickly Access the Stun Function above.
Effects of the Unit on an Assailant
1. Touching an assailant for less than 1 second will cause minor muscle contractions and have a repelling effect.
2. Touching an assailant for 1 to 2 seconds will cause muscle spasms and a dazed mental state.
3. Touching an assailant for 3 to 5 seconds will cause loss of balance and muscle control, total mental confusion, and disorientation. All effects to the
assailant are temporary; the stun batons can cause no permanent harm. (NOTE: The device should not be used for longer than 5 seconds.)
WARRANTY: Streetwise Security Products extends a lifetime warranty to the SWPFTB10R for the product against defects in materials or workmanship, with
the following exceptions:
1. The warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, moisture, the affixing of any attachment not
provided with the product, loss of parts, or recharging the unit in any manner not in accordance with the included instructions.
2. The warranty will be voided if the unit has been opened or tampered with in any way (unless by an authorized dealer) or if any unauthorized replacement
parts have been used.
NOTICE: Purchaser must check and abide by all local laws governing the possession and use of stun batons. In addition, the stun batons must only be used in
a lawful manner for self-defense. NOTE: Not to be used on children, persons with heart disease, or any vital part of the human body. Not to be stored or used
in environments where it is damp or humid or where there are extreme hot or cold temperatures. Do not use on metal objects.
Conditions of Sale: Purchase of this product is an agreement by the purchaser/user to hold all sellers and manufacturers harmless of all liabilities and
damages.
To Obtain Service: Contact the Authorized Dealer from whom you purchased this unit for a Return Merchandise Authorization. The return unit must be sent
postage prepaid and proof of purchase is required. Damage or loss occurring during shipment is not covered by this warranty.