BullFrog 6011 LEA User guide

ASSEMBLY AND INSTRUCTION MANUAL
www.bullfrog-design.com
MODEL 6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R
SLIP COVER WITH BOX PLEATAS AN ADDITIONAL OPTION
A HANG OVER CUSHION
SLIP COVER WITH ZIPPER

T
T
Assembly manual
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
The furniture should always be mounted in pairs (2 persons)!
Information
CONTENTS
2 side panels, 1 foot part (semi-product)
1 headboard (completely upholstered)
1 loose slip cover for corpus of bed
40 hexagon socket countersunk screws
4 corner connectors (2 x le, 2 x right)
1 beech wood centre support rail with angle connectors
1 Allen key, size: 4 mm
Use of slatted frame:
4 slatted frame angles for corner connectors
2 slatted frame angles for side panels,
4 wooden feet
1 plastic foot (120-235 mm)
Use of box spring system:
5 plastic glides (25 mm)
1 plastic supporting foot (44-73 mm)
1 plastic supporting foot (89-125 mm)
1. Unpack the individual parts of the bed, place them as shown at picture
and check the delivered package contents for completeness.
2. For assembly of bed, headboard and
foot part or rather the 2 side panels should
be placed at opposite side, and their
zipper to the center (or in upright position
towards flor). The bores should point
upwards/inwards. The blocked holes are
only for the use of box spring systems. By
the use of box spring system, unscrew the
plastic screws and screw them in the upper
holes.
6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R

Slatted
frame
Box spring frame
Upper side
3. Position the connector angles
with the T-shaped punch-outs in
direction to side panels. Mount 2
angles at headboard and 2
angles at the ends of side panels.
Place screws carefully and
tighten them with an Allen key.
ATTENTION!
There are right and le angles.
4. Set up one of the side panels
and position it at angle. First of all,
place 2 outer screws and slightly
tighten them. Now it will be easier to
place the other screws. Revise these
steps with the other side panel.
5. Next position the foot part and
screw it as pictured at point 4.
6. Slatted frame: screw the 4
wooden feet in the tapped holes
of connector angles.
Box spring sytem: plug in the
plastic gliders in the hole beside
the tapped hole.
7. Slatted frame: take the large
support foot and press it from below
in the hole of the centre support rail.
Box spring system: use one of the
smaller support feet, depending on
the height you decided to adjust.
Use the small support foot for the 2
lower, the medium for the upper
attachment points.
8. Mount the centre support rail at
connectors of headboard and foot
part at the desired height and adjust
the support foot at flor level. First
connect headboard. If the centre
support rail is dicult to mount, slightly
loose the screws of corner angles at
foot part. Aer connecting of centre
support rail tighten the screws again.
9. Mount slatted frame angles at
corner angles and the 2 side panels
at desired height.
Angles of side panels (fig. above).
The insert depth for slatted frame is
height adjustable: approx. 12,5-22 cm.
6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R

10. Place slip cover (with velcro
part inwards) onto corpus of bed.
(Do not yet remove the so side
strap of velcro!)
11. Pay attention that the corner
seams are exactly oriented at mitre
and the parts of box pleat hang
down exactly at the 2 edges in front.
12. Aer you have placed the
cover properly onto the corpus,
remove the velcro (so side strap)
carefully and fix the cover.
Ready covered corpus!
13. Cover with zipper: it is possible
to open/close the zipper at
headboard/foot part as desired.
6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R

A
2
5
7
1
1
1
4
3
B
1
6
89
2
11
4
3
Slatted frame: the connectors (1) and corner angles (2) have to be
mounted with the supplied screws at the upper hole position (A).
At any corner angle (2) screw in at screw threads M8 a 13 cm height wooden
foot (5).
The support bracket (3) and the stabiliser bar (4) have to be connected at
the same level.
When you have decided a height, press the suitable supporting foot tight
into the stabiliser bar (4) and by turning, adjust the floor height.
The large supporting foot (7) can be used for all positions of slatted frames.
Detailed assembly instruction of slatted frames:
Insert depth for slatted frame = 12,5-22 cm
Detailed assembly instruction of box spring frames:
Insert depth for box spring frame = 21,5-31 cm
Box spring frame: the connectors (1) and corner angles (2) have to be
mounted with the supplied screws at the lower hole position (B).
At any corner angle (2) a 2,5 cm height plastic glide feet (6) has to be
plugged 12,5 mm into the bore.
The support bracket (3) and the stabiliser bar (4) have to be connected at
the same level.
Aer you have decided a height, press the suitable supporting foot tight
into the stabiliser bar (4) and by turning, adjust the floor height.
The small supporting foot (8) can be used for the 2 lower positions of box spring
frames. The medium support foot can be used for the upper positions (9).
6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R

6011 LEA
© 2013 K URT BEI E R &KATI QU I N G E R
Keep all documents relating to the purchase of your furniture carefully, even beyond the legal warranty period of 2 years. You will
find all important information in your product folder and also on our website www.bullfrog-design.com
Centre support rail
Support angle
Insert depth approx. 17 cm
Centre support rail
Support angle
Insert depth approx. 19,5 cm
Centre support rail
Support angle
Insert depth approx. 22 cm
Centre support rail
Support angle
Insert depth approx. 17,5 cm
Centre support rail
Support angle
Insert depth approx. 15 cm
Centre support rail
Support angle
Insert depth approx. 12,5 cm
25mm
Centre support rail
Support angle
Insert depth approx. 26 cm
Centre support rail
Support angle
Insert depth approx. 28,5 cm
Centre support rail
Support angle
Insert depth approx. 31 cm
Centre support rail
Support angle
Insert depth approx. 26,5 cm
Centre support rail
Support angle
Insert depth approx. 24 cm
Centre support rail
Support angle
Insert depth approx. 21,5 cm
Slatted frame assembly
with wooden foot 13 cm
Box spring assembly
with plastig glides 2,5cm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
120mm
-
235mm
89mm
-
125mm
89mm
-
125mm
89mm
-
125mm
44mm
-
73mm
44mm
-
73mm
25mm