Stealth Products TWBM480-TAB User manual

OWNERS MANUAL
Mounting Hardware
Flip-Down Tablet Mount
TWBM480-TAB & TWBM480-U
Stealth’s User and Installation Manual
for the Swing-Away Link Style Tablet Mount

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer satisfaction. Your complete
satisfaction is important. Please contact us with feedback or suggested changes
that will help improve the quality and usability of our products. You may reach
us at:
General
Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse due to failure of the following
instructions will void the warranty.
Immediately discontinue use if any function is compromised, parts are missing,
loose, or shows signs of excessive wear. Consult with your supplier for repair,
adjustment, or replacement.
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1(800) 965-9229
Fax: [phone] Toll Free: 1(800) 806-1225
[email protected] www.stealthproducts.com

ii
Important Information 2.0
Important Information!
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in these instructions must be familiar with and understand all safety
aspects of the devices mentioned. In order for our products to be used
successfully, you must:
 Read and understand all instrucons and warnings.
 Maintain our products according to our instrucon on care and maintenance.
 Devices should be installed and adjusted by a trained technician.
Supplier Reference
Supplier:
Telephone:
Address:
Purchase Date:
Model:

iii
Introduction 3.0
Before you install or begin using this product, it is important that you read and
understand the content of these installation and operating instructions. The
installation instructions will guide you through the possibilities with the
flip-down tablet hardware.
Instructions are written with the expressed intent of use with standard
configurations. They also contain important safety and maintenance
information. For further assistance, or more advanced applications, please
contact your supplier or Stealth Products at [phone] or toll free at
1-800-965-9229.
Always keep the operating instructions in a safe place so they may be referenced
as necessary.
All information, pictures, illustrations, and specifications are based on the
product information that was available at the time of printing. Pictures and
illustrations shown in these instructions are representative examples and are not
intended to be exact depictions of the various parts of the product.
Ordering Documentation
You can download additional copies of this Owner’s Manual on the Stealth
website:
https://stlpro.site/stealth-docs
and search: TWBM480-TAB/TWBM480-U Owners Manual in the search bar at the
top of the page.

iv
Warranty 4.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon of product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally void this
warranty.
Stealth Products, LLC is liable for replacements parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials or
workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at [phone] or toll free [phone].
2. Request the Returns Department or obtain an RA from the Returns Department and follow
department or documentaon instrucons.

v
Table of Contents 5.0
1.0 Customer Satisfaction .......................................................................................... i
2.0 Important Information....................................................................................... ii
3.0 Introduction........................................................................................................ iii
4.0 Warranty ............................................................................................................. iv
5.0 Table of Contents................................................................................................. v
6.0 Warning Labels .................................................................................................. vi
6.1 Warning Labels........................................................................................................................ vi
6.2 Limited Liability ....................................................................................................................... vi
6.3 Testing......................................................................................................................................... vi
7.0 Design and Function............................................................................................ 1
7.1 Intended Use ..............................................................................................................................1
7.2 Tablet Mount Specs.................................................................................................................1
8.0 Parts And Accessories ........................................................................................ 2
8.1 Package Overview .................................................................................................................. 2
8.2 Replacements Parts .................................................................................................................3
8.3 Tools ............................................................................................................................................ 4
8.4 Torque Specs..............................................................................................................................4
9.0 Installation Instructions.................................................................................... 5
9.1 Replacing the FDM380.......................................................................................................... 5
9.2 Link Replacement/Adjustment .......................................................................................... 6
9.3 Armrest Mounting................................................................................................................... 7
9.4 Depth Adjustment................................................................................................................... 7
9.5 Flip-Down Mount .....................................................................................................................8
10.0 First Time Use..................................................................................................... 9
10.1 Dealer Assistance ...................................................................................................................9
10.2 User Testing..............................................................................................................................9
10.3 Conditions Of Use..................................................................................................................9
11.0 Maintenance..................................................................................................... 10
11.1 Maintenance ......................................................................................................................... 10
11.2 Cleaning.................................................................................................................................. 10

vi
Warning Labels 6.0
Warning Labels 6.1
Warnings are included for the safety of the user, client, operator and property. Please
read and understand what the signal words SAFETY, NOTICE, CAUTION, WARNING
and DANGER mean, how they could affect the user, those around the user, and property.
Limited Liability 6.2
Stealth Products, LLC accepts no liability for personal injury or damage to property that
may arise from the failure of the user or other persons to follow the recommendations,
warnings, and instructions in this manual.
Stealth Products does not hold responsibility for final integration of final assembly of
product to end user. Stealth Products is not liable for user death or injury.
Testing 6.3
Initial setup and driving should be done in an open area free of obstacles until the user is
fully capable of driving safely.
The TWBM480-TAB/TWBM480-U should always be installed and tested following the
instructions in this owners manual.
NOTI CE
Identifies important information not related to injury, but
possible property damage.
SAFE TY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.
CAUTION Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
WA RNING Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
DAN GER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.

1
Design and Function 7.0
Intended Use 7.1
The TWBM480-TAB/TWBM480-U hardware utilizes Stealth’s link style hardware
to provide limitless adjustment. Multiple planes of adjustment allow critical
adjustment of the tablet mount. Separate links isolate adjustment planes and
angles, while individual link adjustment achieves the most complex support
solutions, making the positioning of your tablet easy and rigid.
The flip-down style hardware offers a sleek design, strong resistance and an
easy flip-down mechanism which allows the tablet to flip away while staying
attached to the chair, eliminating misplacement.
Tablet Mount Specs 7.2
 Mount dimensions for the TWBM480-TAB include:
-Height 8.5 inches to 11.125 inches
-Width 6.38 inches to 7.75 inches
-Depth .13 inches to .56 inches
*Compable with iPad tablets 1-4
 Mount dimensions for the TWBM480-U include:
-Height Minimum/Maximum: 7 inches to 10 inches
-Width Minimum/Maximum: 4 inches to 5.31 inches
-Depth Minimum/Maximum: .44 inches to 1.06 inches
*Compable with 7” tablets
 The TWBM480-U provides 3 sets of interchangeable cup ends.
 Both tablet mounts are designed with spring loaded tension to provide secure support and
quick release of the tablet.

2
Parts and Accessories 8.0
Part Number Description
FDM380 3/4” Diameter Flip-Down Rod
A
B ARM240 3/4” Cane Clamp
C FDM Sleeve Flip-Down Sleeve
D TWB-RH Ratchet Handles (2)
E Inline Link 3” Inline Link
F RAM Tab-Tite™ Tablet Mount for iPad 1-4
G RAM Tab-Tite™ SmallUniversal Tablet Mounting Bracket
B
C
E
F
TWBM480-TAB/TWMB480-U Packages 8.1
TWBM480-TAB mount shown above.
TWBM480-U includes the same components as the TWBM480-TAB.
D
A

3
Parts and Accessories 8.0
Replacement Parts 8.2
 The TWBM480-TAB is featured in drawings throughout the manual.
Part Number Description
TWB-LINK
TWB-LIL-6
FDM380

4
Parts and Accessories 8.0
Tools 8.3
Tools, anti-seize, and Blue Medium Strength Liquid Loctite Series 242 are not provided.
Torque Specs 8.4
Hardware Description
2.5mm T-Handle Set screws on links
5/32 T-Handle All screws on triangle & links
3/16 T-Handle Cane clamp screws
Screws Torque Specification
1/4 x 20 x 1” SHS 200in-lbs
1/4 x 20 x 3/4” SHS 200in-lbs
M5 Shoulder Screw 20nM
1/4 x 20 x 1” FHS 140in-lbs
Set Screws 40in-lbs
10-24 x 1/2” SHS 79in-lbs

5
Installation Instructions 9.0
Replacing the FDM380 9.1
Step 1: Loosen the set screws on the triangle mount with a 5/32 T-Handle, but do not remove. Loosen the
socket screws from the triangle, allowing the thru triangle to be released from the mount.
Step 2: Place the new FDM380 in line with the thru and threaded triangles. The link aachment points must
be aligned with the ip-down slot on the bar to ensure correct movement of the ip-down sleeve.
Step 3: Align triangles and ghten the socket head screws back into place.
Step 4: Add blue Locte to set screws to prevent loosening. Tighten the set screws. Ensure they are snug
but do not overghten. Reference the Torque Spec secon for proper torque specicaons.
Step 5: Tighten the screw and locknut on the vercal bar. There should be minimum lateral movement with
the assembly.
1
2
3
4
CAUTION
Ensure that all screws are tightened evenly on the hardware. Threads can strip
out and cause damage to the hardware if not tightened properly.
NOTICE
Tighten the set screws with the client in the chair and make any final
adjustments necessary.
WARNI NG Overtightening of set screws may cause damage to hardware.
5

6
Installation Instructions 9.0
Link Replacement/Adjustment 9.2
Step 1: Loosen the set screw on oset link with a 4mm T-Handle, but do not remove. Remove the ratchet
handle from the oset link, separang the oset link from the inline link and creang a gap for the
link to be removed or another link to be installed.
Step 2: Align the new link with the oset link. Align the inline link and ensure all drilled holes match up.
Install the number of links necessary to achieve the desired length of the ip-down mount.
Step 3: When the number of desired links have been added to the hardware, ghten all ratchet handles and
ensure all links are in the proper posion. Add blue Locte to the set screws to prevent loosening.
Tighten set screws to proper torque specicaons, but do not overghten.
Step 4: Add Blue Locte to the set screws to prevent loosening. Tighten the set screws. Ensure they are snug
but do not overghten.
2
1
3
NOTI CE
Before installing/adjusting links, loosen the set screws.
NOTICE
The TWBM480-U follows the same installation instructions as shown
throughout the manual.
4

7
Installation Instructions 9.0
Armrest Mounting 9.3
Step 1: Posion the cane of the chair in between the ARM240 clamp.
Step 2: Align the socket head screws with the holes on the clamp and ghten screws with a 3/16 T-Handle
to the recommended torque specicaon.
Depth Adjustment 9.4
Step 1: Loosen the socket head screws on the base of the ARM240 clamp.
Step 2: Slide clamp along the FDM380 bar and place it in the necessary posion.
Step 3: When clamp has been placed in the correct posion, ghten with a 3/16 T-Handle and secure the
screws. Refer to the Torque Spec secon for proper torque specicaons.
1
2
1
2
3

8
Installation Instructions 9.0
Flip Down Mount 9.5
Step 1: To ip the hardware down and away, slide the red ip-down sleeve up.
Step 2: Swing away the hardware in conjuncon with the ip-down sleeve being pushed up.
Step 3: To bring hardware back to the upright posion, move the links and tablet back to a parallel posion
with the ground. An audible ‘click’ should occur, indicang that the hardware is locked back into
place.
CAUTION
Ensure the red flip-down sleeve freely rotates 360°. If the flip-down sleeve does
not rotate, the hardware will not work properly.
SAFE TY
Move hands from the flip-down sleeve area when bringing it back to a vertical
state. The sleeve could pinch when moving and could cause injury.
CAUTION Ensure the flip down mount is fully engaged before use.
1
3
2

9
First Time Use 10.0
Dealer Assistance 10.1
During first time use by the client, it is advised that the dealer or service
technician assists and explains the configuration to the customer (the user
and/or the attendant). If needed, the dealer can make final adjustments.
User Testing 10.2
It is important that the customer is fully aware of the installation and how the
hardware can be adjusted in order to gain the best positioning possible. As a
dealer, proceed as follows:
 Explain and show the customer how you have executed the installaon, and explain
the funcon.
Have the user test the position of the TWBM480-TAB/TWB480M-U hardware:
 Is the hardware in the proper posion for the client?
 Can the user safely operate the chair?
If needed, adjust the hardware to the proper position.
Explain to the customer any possible issues and how to address them.
Conditions of Use 10.3
The TWBM480-TAB/TWBM480-U is intended for use as installed by the dealer,
in accordance to the installation instructions in this manual:
 The foreseen condions of use are communicated by the dealer or service technician to
the user and/or aendant during the rst me use.
 If the condions of use change signicantly, please contact your dealer or a qualied
service technician to avoid excessive wear and tear or unintended damage.
WAR NING
The TWBM480-TAB/ TWBM480-U should only be prescribed and fitted by
qualified health care professionals.

10
Maintenance 11.0
Maintenance 11.1
All parts should be checked on a regular basis and repaired, if necessary, by a service
technician.
Disconnue use aer idenfying loose or broken components.
Periodically check the ip-down sleeve. Test that it engages properly and makes an audible
‘click’ when back in the vercal posion.
Check that the tablet mount is secure.
Check the M5 bolt on the vercal bar. Tighten if it has become loose.
To prevent screws from seizing, reapply copper an-seize if necessary.
If you are experiencing excessive lateral movement with the hardware, refer to Step 5 on
page 5 for adjustment instrucons.
Cleaning 11.2
Wipe hardware clean with a damp cloth and mild, non-abrasive cleaner.
Ensure any cleaners used to disinfect are approved for cleaning aluminum surfaces.
DANGER
Failure to comply with these warnings could result in serious bodily harm.

11
NOTES 12.0

12
NOTES 12.0

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P139D17 Revision Date 2019-12-17