Strong SM-CBP Series User manual

SM-CBP Series
Universal Fixed & Tilt Mount for Portrait Displays
Install Guide

2
WARNINGS:
• These wall mounts are intended for use only with the
maximum weight capacities listed below.
• Installation by a qualified professional is highly
recommended for this product.
• Do not begin installation until you have thoroughly read
and understand these instructions.
• Ensure the mounting wall will safely support four times the
combined weight of the mount and display panel.
• The manufacturer does not accept responsibility for
incorrect installation.
CAUTION:
• Use with heaver than the maximum weight indicated may
result in instability which could possibly cause injury.
AVERTISSEMENTS:
• Ces supports muraux sont pour être utilisés seulement
avec les capacités de poids maximales ci-dessous.
• L’installation par un professionnel qualifié est fortement
recommandée pour ce produit.
• Ne commencez pas l’installation avant d’avoir lu et
compris ces instructions.
• Assurez-vous que le mur de montage supporte en
toute sécurité quatre fois le poids total du support et du
panneau d’achage.
• Le fabricant n’accepte aucune responsabilité pour une
installation incorrecte.
MISE EN GARDE:
• Une utilisation avec un poids plus haut que le poids
maximal indiqué peut provoquer une instabilité et ainsi
des blessures
Specifications
• Maximum Load: 200 lbs
• Tilt Range (SM-CBP-T): +12°/-3°
• Post Install Adjustment: 0.60"
• Fits VESA from 50×50 to 400×600
Tools Required
• Power Drill w/ 5/16" and 5/32" bits
• Phillips Screwdriver
• Level
• Socket Wrench with ⁄" head
Box Contents
• Wall Plate
• Arm, Left
• Arm, Right
• Hardware Kit
• Security Bar
Hardware Kit
Bag 1
(A) Lag Bolt
8 × 63mm 5
(B) Lag Washer
8.4 × 19 × 2 mm 5
(C) Concrete Anchor
10 × 50mm 5
(D) Screw,
M6 × 20mm 4
(E) Screw,
M6 × 40mm 4
(F) Screw,
M8 × 20mm 4
Bag 2
(G) Screw,
M8 × 40mm 4
(H) Screw,
M8 × 50mm 4
(I) Spacer,
8.5 × 15 × 4.6 4
(J) Spacer,
8.5 × 17.5 × 19 4
(K) Spacer,
8.5 × 17.5 × 22 4
Bag 3
(L) Washer,
M6 × 2mm 8
(M) Washer,
M8 × 2mm 8
Hex Wrench 1
(N) M5 Security Nut 1

3
Installation
Warning: Tighten bolts so that the wall plate is firmly attached, but do not overtighten.
Overtightening can damage the bolts, greatly reducing their holding strength.
Step 1: Mount the Wall Bracket Assembly
On a Wood-Stud Wall
Warning: Studs must be a minimum of 2"×4" and covered with no more than 3/8" thick drywall.
Drill two pilot holes each into two wood studs using a 5/32"
drill bit. Drill at least 2⁄" deep into the center of the studs.
Insert four lag bolts (A) with washers (B) through the wall
plate and tighten.
On a Concrete Wall
Warning: Concrete must be 2500 psi density minimum. Ensure that the
supporting surface will safely support the combined load of the
equipment and all attached hardware and components
Drill 5/16" pilot holes into concrete to a depth of 2⁄". Insert concrete wall
anchors (C). Tap in with hammer if necessary.
Insert four Lag Bolts (A) with Washers (B) through the Wall Plate into the holes
and tighten.
Step 2: Attach Arms to the TV
Determine the diameter of the screw (parts D through
H) your TV requires by carefully hand-threading one into
the threaded insert on the rear of the TV. If there is any
resistance, stop immediately.
Place the arms with the flat side to the TV and square to
each other. Add spacers (parts I through K) as necessary
if the TV has a curved back or recessed screw inserts.
Thread each screw through a washer (L or M), the arm,
any spacers needed, and into the TV, and tighten.
Drill pilot holes here

4
Technical Support
For chat and telephone, visit https://tech.control4.com/s/contactsupport • Email: [e-mail]
Visit tech.control4.com/technician for discussions, instructional videos, news, and more.
Warranty and Legal Notices
Find details of the product’s Limited Warranty and other resources such as regulatory notices and patent and safety
information, at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
Copyright ©2022, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks
or trademarks of Snap One, LLC, in the United States and/or other countries. Control4 and Strong are also registered
trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective
owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies,
or product use risks. Information within this specification subject to change without notice.
220408-1145
Part # 200-SM-CBP-X-B
Step 3: Hang the TV on the Wall Plate
Carefully lift the TV to hook the arms over the top lip of the
wall plate. This leaves the locking tab at the bottom of the
arms to rest on the top edge of the locking mechanism.
Release the locking mechanism by pulling the pull strings
down, and allow the TV to slide into place. Release the
pull strings to lock the TV. Keep hold of the TV until it is
completely connected to the wall plate.
Insert Security Bar
Slide the security bar through the holes at the bottom of
the arms and the flanges in the wall plate. Use the hex
wrench to secure the security nut to the security bar.
Step 4: Adjustments
Tilt Adjustment:
The tilt adjustment lever is a ratcheting device designed to assist
you as you tighten the arms to your desired tilt position (it is very
similar to a ratcheting socket wrench). To disengage the ratchet,
push the button and pull the lever away from the arm; let the lever
drop back in place to re-engage the screw.
Turn the tilt adjustment lever clockwise to tighten the screw,
moving the TV to be more upright. Turn it counter-clockwise to
loosen the screw, tilting the TV down.
Level Adjustment: To level the display horizontally, use the hex
wrench to raise or lower the adjustment screws that are found at
the top of each arm.
Adjustment
Screw
Locking Tab
Arm Hook
Tilt
Adjustment
Lever
(Ratchet)