Strong SM-PAD-LIFE User manual

Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components
found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to prod-
ucts which have been abused, modied or disassembled. Products to be repaired under this warranty must be returned
to SnapAV or a designated service center with prior notication and an assigned return authorization number (RA).
For Technical Support call 1.866.838.5052
Lifetime
110713
SM-PAD-LIFT
Strong™ Lift-off Mount for iPad®
with 90 Degree Rotation (Black)
ATTACHING THE MOUNT TO THE IPAD
1. Remove the 4 thumbscrews
to separate the bezel from
the base plate.
2. Place the iPad on the bezel, face
down as shown. Ensure the iPad
  tssnuglyinthebezel.(ForiPad2
installation, see the additional manual).
3. Ensure the rubber bumper is
  seatedproperlyonthebaseplate.
4. Place the base plate over the bezel
and iPad.
5. Secure the base plate to bezel and
iPad with the 4 thumb screws.
(Optional phillips head #6-32 x 3/8”
screws can also be used to hold the
base plate to the bezel).
FINAL ASSEMBLY
1. Slide the lift off plate into the
wall plate. Make sure the lift
  offplateisseatedproperly.
2. Secure the lift off plate to the
wall plate using the lock screw.

TOOLS REQUIRED
 •5/32”x2½”drillbitandStudnderforDrywallinstallation
 •5/16”x2½”MasonrydrillbitforConcreteinstallation
 • Philips head screw driver
 • Electric or portable drill
 • Hammer
 • Level
INSTALLING THE WALL PLATE (CONCRETE)
1. Place the wall plate against the wall in the desired location and level it. Mark
the four, outer-most holes for securing the mount and set the wall plate aside.
  WARNING:WheninstallingWallArmAssemblyoncinderblock,verify 
  rstthatyouhaveaminimumof1-3/8”ofconcretethicknesstobe
  usedfortheConcreteWallAnchors.Donotdrillintomortarjoints!
  Besuretomountinasolidpartoftheblock,generally1”minimum
  fromthesideoftheblock.CinderblockmustmeetASTMC-90
  specications.Itissuggestedthatastandardelectricdrillonslow
setting is used to drill the hole instead of a hammer drill to avoid
  breakingoutthebackoftheholewhenenteringavoidorcavity.
  Concretemustbe2000psidensityminimum.Lighterdensityconcrete
  maynotholdconcreteanchor.
  Makesurethatthesupportingsurfacewillsafelysupportthecombined 
load of the equipment and all attached hardware and components.
2. Drill a 2-1/2” deep hole at marked locations
  usinga5/16”(8mm)drillbit.Removeany
excess dust from the holes.
 3. InsertConcreteWallAnchorsintoeach
  holesothatitsushwiththeconcrete
  surface.Ahammercanbeusedtolightly
  taptheanchorsintoplaceifnecessary.
  NOTE:Iftheconcretewalliscoveredby
  alayerofplasterordrywall,theconcrete
  anchormustpasscompletelythroughthe
  layertorestushwiththeconcretesurface.
4. Move the wall plate back into position and
secure it using the Wood Screws from the
hardware kit. Do not over-tighten these screws.
INSTALLING THE WALL PLATE ON DOUBLE GANG J-BOX
(OR MUD-RING)
1. Place the wall plate against the J-Box.
Line up the mounting holes of the wall
plate with the holes in J-Box
2. Secure the wall plate to the J-Box
using #6-32 x 1/2” Phillips Pan
head mounting screws.
HARDWARE KIT
#6-32 x 1/2” Phillips
Pan Head screws (x 4)
Concrete Wall
Anchor (x2)
Phillips Tip (x1)
INSTALLATION INSTRUCTIONS
INSTALLING THE WALL PLATE (DRYWALL)
IMPORTANT!Forsafetyreasons,thismountmustbesecuredtoawoodstud.
Thestudmustbecapableofsupportingthecombinedweightofthemountand
thedisplay.
 1.Useahigh-qualitystudndertolocatethesinglestudwhereyou
  wanttoinstallyourmount.Markbothedgesofthe
  studtohelpidentifytheexactcenter.
2. Place the wall plate over the center of the
marked stud and level it. Mark the two
holes for securing the mount and set the
wall plate aside.
3. Drill a 2-1/2” deep pilot hole at each
marked location using an electric or
portable drill and a 5/32” drill bit.
4. Move the wall plate into position and
secure it using wood screws.
WARNING: Tighten screws so that the
 WallPlateisrmlyattached,butdonot
 overtighten.Overtighteningcandamage
 thescrews,greatlyreducingtheirholdingstrength.
BOX CONTENTS
 •(1)SM-PAD-LIFTmount
 • (1) Instruction manual
 • (1) Ipad 2 kit
 • (1) Hardware kit
#12x2.5” Philips
Sheet Metal Screw (x2)
#6-32 x 3/8” Phillips
Pan Head screws (x 4)