Strong SM-FLAT-S User manual

Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components
found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to prod-
ucts which have been abused, modied or disassembled. Products to be repaired under this warranty must be returned
to SnapAV or a designated service center with prior notication and an assigned return authorization (RA) number.
For Technical Support call 1.866.838.5052
Lifetime
SM-FLAT-S
Strong™ Small Low Prole Flat Mount
(Black)
Step 3: Attach the Adapter Plate
to the Display
a. Attach the Adapter Plate to the display using
M4, M5, M6, or M8 screws. For displays with
a hole pattern in a pocket or inputs behind
Adapter Plate, spacers go between Adapter
Plate and display (Fig 3).
Step 4: Attach the Adapter Plate with
Display to Wall Arm Assembly
a. Attach Adapter Plate and Display onto
Wall Arm Assembly, ensuring top and
bottom hooks slide into holes of Mounting
Head (Fig 4).
b. Using a long-nosed Philips Head Screwdriver,
tighten down Locking Screw located on
Adapter Plate into threaded hole in the
Mounting Head on Wall Arm Assembly.
Fig 3
Fig 4
150408-1643
© 2015 STRONG™

WARNINGS
• We highly recommend this product be installed by a qualied professional.
• Please do not begin installation until you have thoroughly read and
understood these instructions.
• This mount supports display mounting from VESA 75X75,
100x100 & up to 200x100 and supports a maximum load of 40 lbs (18.2 kg).
• Ensure the wall that you plan to use will safely support four times the
combined weight of the mount and your chosen display.
• The manufacturer does not accept responsibility for incorrect installation.
SPECIFICATIONS
• Maximum Load: 40 lbs. (18.2 kg)
• Prole: ¾”
BOX CONTENTS
• Wall Arm Assembly (1)
• Adapter Plate (1)
• Hardware Kit (1)
INSTALLATION INSTRUCTIONS
Step 1: Use Wall Plate to Mark Mounting Hole Locations
a. The use of a stud nder is highly recommended.
Step 2: Mount the Wall Arm Assembly
For Mounting on a Stud Wall (Fig 1)
a. Pre-drill two holes into stud using a 3/16” drill bit.
Be sure to drill into the center of the studs.
b. Insert two Lag Screws into holes through
the Wall Plate and tighten down. Be sure
the Wall Plate is mounted with the mounting
tabs pointing upwards.
WARNING: Tighten screws so that the
Wall Plate is rmly attached, but
do not over tighten. Over tightening
can damage the screws, greatly
reducing their holding strength.
For Mounting on a Concrete Wall (Fig 2)
a. Pre-drill two holes into concrete using 5/16”drill bits. Insert Concrete Wall
Anchors and tap in with hammer, if necessary.
WARNING: When installing Wall Arm Assembly on cinder block, verify rst that
you have a minimum of 1-3/8”of concrete thickness to be used for the
Concrete Wall Anchors. Do not drill into mortar joints! Be sure to mount in
a solid part of the block, generally 1”minimum from the side of the block.
Cinder block must meet ASTM C-90 specications. It is suggested that a
standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering
a void or cavity.
Concrete must be 2000 psi density
minimum. Lighter density concrete
may not hold concrete anchor.
Make sure that the supporting surface
will safely support the combined load
of the equipment and all attached
hardware and components.
b. Insert two Lag Screws into the
Wall Anchors through the Wall
Plate. Be sure the Wall Plate is
mounted with the mounting
tabs pointing upwards.
WARNING: Tighten screws so that wall plate
is rmly attached, but do not over tighten.
Over tightening can damage the screws,
greatly reducing their holding strength.
HARDWARE KIT
M4 x 12mm Philips
Head Screw (x4)
Concrete Wall Anchor (x2)
M4 x 20mm Philips
Head Screw (x4)
TOOLS REQUIRED
• Power Drill
• 3/16” (5mm) Drill Bit
• 5/16” (8mm) Masonry Bit
• Phillips Head Screw Driver
• Level
Fig 2
Fig 1
#14 x 2.5” Lag Screw (x2)
CAUTION:
This wall mount is intended
for use only with the maximum
weight of 40 lbs (18.2kg).
© 2015 STRONG™Page 2 Page 3