Sulzer ABS CA 461 User manual

81907022A (12.2020)
en
www.sulzer.com
3 4 5 6
3 4 5 6
110-230VAC
L1 N
CA 461
CA 461
Leakage Control Type ABS CA 461
Installation guide

2
81907022A
1 FUNCTION AND USAGE
CA 461 is a standalone leakage detection monitor for DIN rail mount.
1.1 Function
In case of water leakage, the resistance between the sensor electrode and housing will decrease. If the resistance becomes lower
than 100k ohms (±10 %), the output goes active and contact on terminals 5 and 6 is closed. The signal has to be stable for 10 seconds
before the output is activated.
Terminal Description
1 Power supply (N)
2 Power supply (L1)
3 Ground / Pump chassis
4Input(s) from pump probe(s)/anode(s)
5Output contact
6 Output contact (NO)
Leakage: Sensors must be in parallel.
It is very important to have in mind that this practice avoids alarms having to be distinguished. Sulzer highly recommends to use one
module per signal to allow not only distinguishing but also acting in a di󰀨erent way according to the alarm category/severity.
If the pump is operated from a motor drive or frequency converter, special precautions are required.
The high electric noise level can distort electrical readings and in extension jeopardize functionality.
To avoid conducted electrical noise, follow best practices and manufacturer EMC compliance recommendations when installing
frequency converters. Use shielded cables and 50 cm separation between power and signal cables. Ensure that the cables are also
separated from each other in cabinets.
Input
Leakage
Power Supply
Connect terminal 3
to ground or housing
of the pump.
Output
3 4 5 6
110-230VAC
L1 N
CA 461
en
Leakage control type CA 461
Installation Guide
Copyright © 2019 Sulzer. All rights reserved.
This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with
the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and
should not be construed as a commitment by Sulzer. Sulzer assumes no responsibility or liability for any errors or inaccuracies that may
appear in this book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Sulzer.
Sulzer reserves the right to alter specications due to technical developments.
en

3
81907022A
60 mm
(2,36)
58 mm
(2,28)
108 mm
(4,25)
108 mm
(4,25)
35 mm
(1,38)
en
2 TECHNICAL DATA
2.1 Technical data CA 461
Leakage sensor voltage 12 VDC
Max sensor current < 15 µA
Leakage detection threshold < 100 kohm
Alarm on delay ~10 seconds
Ambient operating temperature –20 to +50 °C (–4 to +122 °F)
Ambient storage temperature –30 to +80 °C (–22 to +176 °F)
Degree of protection IP 20, NEMA: Type 1
Housing material PC,PPO, and POM
Mounting DIN Rail 35 mm
Humidity 0–95% RH non-condensing
Dimensions H x W x D: 108 x 35 x 58 mm
(4.25 x 1.38 x 2.28 in.)
Power supply 110-230 VAC, 50 Hz/60 Hz
Fuse Max 10 A
Terminal wire size Use copper (Cu) wire only. 0.2 - 2.5 mm2
exible core, stripped length 8 mm.
Power consumption < 2 W
Max load output 250 VAC 3 Ampere
Altitude Max 2000 MASL or 6562 ft. AMSL
Attention If the unit is used in a manner not described in this document the protection provided by the equipment may be impaired.
2.2 Dimensions
2.3 Cleaning
How to clean the unit
Power o󰀨 the unit and only outside/front shall be cleaned by using a dry, soft cloth. A good choice would be the
microber type of cloth. Gently wipe the CA 461 unit front in order not to scratch the overlay. If the dry cloth did not
completely remove the dirt, do not press harder in an attempt to scrub it o󰀨.
If necessary, moisten the cloth by adding a small amount of water with a thin solution of mild detergent and try again.
Never use detergent with polish or solvent which can have an impact on the plastic surface.

Sulzer Pump Solutions (Kunshan) Co., Ltd, No.8 West Chenfeng Road, Kunshan, Jiangsu Province, 215300, China
Tel. [phone]. www.sulzer.com
Copyright © Sulzer Ltd 2020