Summa TRAY ONE User manual

Notice
Summa reserves the right to modify the information contained in this User Manual at any time
without prior notice. Unauthorized copying, modification, distribution or display are prohibited.
All rights reserved.
EU Waste Electrical and Electronic Equipment (WEEE) Directive
The symbol (right) is shown on this product. It indicates that the product should not
be placed in municipal waste but should be disposed of separately.
Electrical and electronic equipment can contain materials, which are hazardous to the
environment and human health, and therefore should be disposed of at a designated
waste facility or returned to your retailer for the appropriate recycling to take place.
If you wish to dispose of this product and the product still functions, please consider
recycling/reusing it by donating it to a charity shop, selling it or exchange parts of it with your
retailer.
Copyright © Summa
Registering Your Device
Please register your cutter on the following link:
http://www.summa.be/registration.html
0H
Contact Information
All inquiries, comments or suggestions concerning this and other Summa manuals should
be directed to:
Summa, nv
Rochesterlaan 6
B-8470 GISTEL
Belgium
www.summa.com
Summa America
100 Cummings Center Suite #151-G
Beverly MA 01915
USA
www.summaamerica.com
[phone]

Table of contents I
Table of Contents
1Setup..............................................................................................................1-1
1.1.1 Driver installation.......................................................................................................1-4
1.1.2 Parameter settings on cutter....................................................................................1-4
2Usage ............................................................................................................ 2-1
2.1.1 General .......................................................................................................................2-1
2.1.2 Making template if plug-in is not available for your design software ................... 2-2

Setup 1-1
1SETUP
The sheet feeder comes in two boxes. One box is with the parts that are specific for your model
of cutter. Before assembling the sheet feeder check if that box is the correct one. This box will
be referred to as box 2 in the assembly procedure below.
Put the plate from box 1 and from box 2 on
the table, they fit like a jigsaw puzzle.
Take the 4 aluminum feet holders an screw
them on the plates.
Screw a bracket on the side of the tray with
two washers and two large grip knobs. Mind
the orientation of the washers (see detail).
1.1 Assembling the sheet feeder

Tray One User’s Manual
Setup 1-2
Do the same at the other side.
Slide the tray in the slots of the plates
Put the brackets over the threaded pins and
secure the with 4 washers and the smaller
grip knobs. Mind the orientation of the
washers (see detail)
Make sure the rear roll on the cutter is in its
most back position. Locate the 4 feet on the
cutter. They will fit in the feet holders that
just have screwed on the plates in step 2 of
this procedure.
Put the cutter on the plate make sure the feet
fit in the feet holders.

Tray One User’s Manual
Setup 1-3
Fully assembled.
2 magnetic blocks to hold loaded sheets
aligned.
Position pinch rollers (left one fixed, right
one adjust to sheet size)
1.
Connect adapter (next to sheet feeder
ON/OFF switch)
2.
USB cable that needs to be connect to
computer
3. Cable to cutter USB port.

Tray One User’s Manual
Setup 1-4
1.1 Set up computer and connect
The program GoSign is used to drive the sheet feeder and cutter. Install first the program
GoSign before connecting the cutter to the computer. During the installation of the program
all the necessary files for the drivers will be copied to the computer. The moment the cutter
and sheet feeder are connected with the computer, the driver will be correctly installed.
NOTE: The minimum version of GoSign for using the sheet feeder is 2.1. If an
earlier version is installed on your computer, then upgrade first.
For the S One cutter, the parameter sheet feeder has to be set ON.
For the SummaCut cutter a couple of parameters need to be changed separately.
For the S One
1. Power on machine.
2.
Press on the barcode icon.
3.
Scroll down with arrow and
press on Configuration.
4.
Scroll down with arrow and
press on Sheet feeder.
5. Press on ‘On’.
6. Press confirm.
7.Press on home icon.
S1D60
Insert media and lower the
pinch rollers
Configuration 1
LAN 192.168.10.2
FlexCut
Tool
Actions
Settings
Calibrations
Configuration
Media sensor
Sheet feeder
Configuration
OPOS parameters
Factory defaults
Autoload
Recut offset
Off
Sheet feeder
Off
Sheet feeder
Ethernet
Wi-Fi
USB port
Language
Media units
OPOS parameters
Configuration
1.1.1 Driver installation
1.1.2 Parameter settings on cutter

Tray One User’s Manual
Setup 1-5
For the SummaCut:
1. Power on the cutter (see section 1.4.3).
2. Press .
‘KNIFE PRESSURE’ will appear on the LCD.
3. Press .
‘SYSTEM SETUP’ will appear on the LCD.
4. Press .
‘ACTIONS’ will appear on the LCD.
5. Use or to scroll through the menu until ‘Configuration’ is reached. Press .
‘IP CONFIG’ will appear on the LCD.
6. Use or to scroll through the menu until ‘AUTOLOAD’ is reached. Press .
The value of the chosen parameter will appear on the LCD.
7. Press or to change the value to ‘OFF’.
‘OFF’ will appear on the LCD.
8. Press to confirm.
An asterisk will appear before OFF, indicating it is now the selected setting.
9. Press to confirm.
‘IP CONFIG’ will appear on the LCD.
10.Use or to scroll through the menu until ‘MEDIA SENSOR’ is reached. Press
The value of the chosen parameter will appear on the LCD.
11.Press or to change the value to ‘OFF’.
‘OFF’ will appear on the LCD.
12.Press to confirm.
An asterisk will appear before OFF, indicating it is now the selected setting.
13.Press to confirm.
14.Press twice to leave the menu.

Usage 2-1
2USAGE
The sheet feeder is driven by GoSign. GoSign can import pdf files created by programs like
Adobe Illustrator or CorelDRAW.
It is highly recommended to use layers when designing the job in your program. One layer
contains the design that needs to be printed and another layer will have the cut lines in them.
The registration marks needed for the cutter to be able to read the position of the printed design
are best put on a third layer.
You can either work with a template with registration marks or use the GoSign plug-in from
Summa for Illustrator or CorelDRAW to add the registration marks.
The layer with the print data and the layer with the registration marks is then printed, the layer
with the cut data and the registration marks is then send to the program GoSign. Either by
exporting them to a pdf file, or by using the GoSign plug-in.
When a template is created with registration marks then make sure the marks should be 3mm
in size and put at equal distance in both direction (X and Y).
Below a sample of how the job is built up.
Layer with print data
Layer with cut data
Layer with registration marks
The grey border is just a way of marking the page size.
The line at the bottom in the registration mark layer is there because the marks were created
with the plug-in for Illustrator or CorelDRAW that Summa provides.
The two outer layers are printed, the middle and right layer are converted into a pdf file for the
program GoSign (if the plug-in to open the file direct from Illustrator or CorelDRAW).
2.1 Preparing the job in your design software
2.1.1 General

Tray One User’s Manual
Usage 2-2
NOTE
: Recommended layer names are:
Print Data for the layer with the print data.
Regmark for the layer with the registration marks on them
NOTE
: If the layer name of the layer with the print data is always the same, then
there is a setting in GoSign to ignore the data from this layer. This makes it
unnecessary to disable the layer before exporting.
A template can be made if the plug-in is not used. Easiest is to make a template with the marks
as far outward as possible so that he maximum space of the sheet can be used. When making
this template, please take in account the margin settings in your printer driver and/or the
limitations of the printer. Best way is to make a template, print that blank template out. Measure
the distances between the marks and the sheet edges and adjust the template if needed.
The minimum distances between the marks and edges of the sheets are 10mm at both sides
and at the bottom. The minimum distance ate the top of the sheet need to be 35mm.
35 mm
4 x 3x3mm
2.1.2 Making template if plug-in is not available for your design software

Tray One User’s Manual
Usage 2-3
2.2 Output the job
When a job is opened in GoSign then everything is normally set ready for output.
In the sample above a separate action, set has been made for output to the cutter with the
sheet feeder installed. If there is no special action set made, then you will have to change the
setting for usage with a sheet feeder each time data is sent to the cutter.
To make a special action set for the sheet feeder make sure these parameters are set like in
the figure below.

Tray One User’s Manual
Usage 2-4
Click on the output action to send the cut file to the sheet feeder.
The cutter will load the first sheet and prompt the user to put the tool above the first
registration mark.
For S one:
Use the arrow keys to set the
tool above first mark.
Pres to confirm.
For SummaCut:
Use , , and to set the tool above first mark.
Press to confirm.
The cutter will read the marks and cut the first job.
When the job is done, the sheet will be ejected into the tray. The cutter will take the next sheet
and move automatically above the first mark, read all the registration marks and cut the job.
This will continue un till all the sheets are cut, or when the number of copies, if it is fille din in
GoSign , is reached.
Set tool
above the
first mark
X 0.00 Y 1150.00
Set tool
above the
first mark
X 0.00 Y 1150.00

Tray One User’s Manual
Usage 2-5
2.3 Using a rip instead of a standard printer driver
When a rip is used, then the registration marks can be set by the rip and the file with cut data
will be a typical cut file with DMPL or HPGL data in it. In this case the pro Pack for GoSign will
have to be purchased since the standard version of GoSign cannot import DMPL, DMP, HPGL
or HPG files.