Summers M94 User manual
Operator’s
Manual
MOUNTED HARROW
M94, M104, M105, M106 AND M108
ROLLING CHOPPERS
ROLLING BASKETS
SUMMERS MANUFACTURING CO., INC.
WEB SITE: www.summersmfg.com
DEVILS LAKE, NORTH DAKOTA 58301 ................................................... (701) 662-5391
© Summers Mfg. Co., Inc. 2018 Printed in USA
IMPORTANT
THE OPERATOR IS RESPONSIBLE FOR
ADJUSTING THE MACHINE SINCE MACHINE
DOES NOT COME “FIELD READY” FROM
FACTORY.
CAUTION
READ & UNDERSTAND OPERATOR’S MANUAL
BEFORE USING MACHINE.
Warranty
Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which
occur during normal use within 36 months from the date of purchase by the end user from Summers’ dealer.
Summers’ obligation is to replace free of charge any part of any product that Summers inspection shows to be defective excluding trans-
portation charges to Devils Lake, ND and return and also excluding all transportation costs from Summers’ dealer to the dealer’s customer
and all other costs such as removal and installation expense.
Summers shall not be liable for loss of time, manufacturing costs, labor, material, loss of prots, consequential damages, direct or indirect,
because of defective products whether due to rights arising under the contract of sale or independently thereof, and whether or not such claim
is based on contract, tort or warranty.
Written permission for any warranty claim return must be rst obtained from authorized Summers’ personnel. All returns must be ac-
companied with a complete written explanation of claimed defects and the circumstances of operational failure.
Written warranty for all component parts used in the manufacture of Summers products is available upon request. Warranty of such
component parts will be determined by said component manufacturer upon their inspection of the claimed defective part.
This express warranty is the sole warranty of Summers. There are no warranties, which extend beyond the warranty herein expressly
set forth. The sales for products of Summers under any other warranty or guarantee express or implied is not authorized. This warranty voids
all previous issues.
SUMMERS MANUFACTURING CO. INC.
DEVILS LAKE, NORTH DAKOTA 58301
1/16
INTRODUCTION
This manual provides the following information about your Mounted Harrow or Mounted Rolling Chopper.
ITEMS OF IMPORTANCE
A. Summers Mfg. Co., Inc. strongly recommends that each Operator READ and UNDERSTAND the Oper-
ator’s Manual before using the machine. In addition, this Operator’s Manual should be REVIEWED
at least ANNUALLY thereafter.
B. It is the policy of this company in improve its products whenever possible and practical to do so.
We reserve the right to make changes or improvements in the design or construction of parts at any
time without incurring obligations to install such changes on products previously delivered.
C. Reference to “right” and “left” in this manual is determined from a seated position in the drivers seat.
D. Parts are referenced in each drawing with the Summers Manufacturing Part Number. Use this Part
Number when ordering replacement parts from your Summers dealer.
E. Summers Mfg. can not be responsible for implement frame damage due to draft or weight of Mounted
Attachments.
OWNER REGISTER
Name____________________________________ Size _________________________________________
Address _________________________________
City _____________________________________
State/Prov. ______________________________ Date Purchased______________________________
Mail Code________________________________ Dealer_______________________________________
TABLE OF CONTENTS
Safety Section .......................................................................................................................................1-5
Disk Mounted Harrow Installation Guide.............................................................................................. 6
Mounting Arm Assembly - M94, M104, M105, M106 & M108........................................................... 7
4-1/2’, 6’ & 7-1/2’ 3-Bar M94 Section Assembly.................................................................................. 8
4-1/2’, 6’ & 7-1/2’ 4-Bar M94 Section Assembly.................................................................................. 9
6’, 8’ & 10’ 3-Bar M104-M108 Section Assembly............................................................................... 10
6’, 8’ & 10’ 4-Bar M104-M108 Section Assembly............................................................................... 11
Disk Brackets........................................................................................................................................ 12
JD510/512 Disk Ripper......................................................................................................................... 13
Mounting Instructions for Cultivators, Chisel Plows & Disks ...........................................................14-16
Mounting Instructions for JD1610/610 - M74...................................................................................... 17
Mounting Instructions for Disk Mounting Brackets............................................................................. 18
Mounting Instructions for JD235 Disks - M74...................................................................................19-21
Packing Lists......................................................................................................................................... 22
Rolling Chopper Assembly ................................................................................................................... 23
Rolling Basket Arms ............................................................................................................................. 24
Rolling Basket Assembly...................................................................................................................... 25
1
SAFETY-ALERT SYMBOL
This symbol is used to denote possible danger
And care should be taken to prevent bodily
Injury. This symbol means:
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
Denition of each Signal Word used in conjunction with the Safety-Alert symbol.
indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury. This signal word is to be limited to the most extreme situations.
indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
indicates a potentially hazardous situation which, if not avoided, may result in minor or moder-
ate injury. It may also be used to alert against unsafe practices.
GENERAL SAFETY PRACTICES
1. READ AND UNDERSTAND Operator’s Manual before using machine. Review at least annually
thereafter.
2. VERIFY all safety devices and shields are in place before using machine.
3. KEEP hands, feet, hair and clothing away from moving parts.
4. STOP engine, place all controls in neutral, set parking brake, remove ignition key and wait for all
moving parts to stop before servicing, adjusting, maintaining or unplugging.
5. BE CAREFUL when working around high pressure hydraulic system.
6. ALWAYS make sure that pressure is relieved from hydraulic circuits before servicing.
7. DO NOT ALLOW RIDERS.
8. USE EXTREME CARE when adjustments.
9. KEEP CHILDREN AWAY from machinery at all times.
10. NEVER ALLOW anyone to walk or work under a raised piece of equipment without installing transport
locks.
DANGER
WARNING
CAUTION
SECTION 1 - SAFETY
2
SECTION 1 - SAFETY
SAFETY DURING TRANSPORT
1. ONLY TOW at a safe speed. Use caution when making corners or meeting trafc.
2. USE a safety chain between tractor drawbar and implement hitch when transporting on public roads.
3. ALWAYS use transport locks when transporting on public roads.
4. COMPLY with local lighting, marking and maximum width regulations when transporting on highways.
SAFETY DECALS
1. KEEP SAFETY DECALS AND REFLECTORS CLEAN.
2. REPLACE missing or unreadable decals. New decals are available from your Summers dealer by
stating correct part number (PN) located in lower right hand corner.
1. TRANSPORT LOCK DECAL (PN 8Z0075)
2. GENERAL CAUTION DECAL (PN 8Z0276)
3
SECTION 1 - SAFETY
3. WING DANGER DECAL (PN 8Z0344)
4. ELECTROCUTION DANGER DECAL (PN 8Z0346)
5. PINCH POINT DECAL (PN 8Z0087)
4
SECTION 1 - SAFETY
6. AMBER REFLECTOR (PN 8Z0800)
7. RED-ORANGE REFLECTOR (PN 8Z0805)
8. RED REFLECTOR (PN 8Z0810)
5
SECTION 1 - SAFETY
GENERAL ASSEMBLY SAFETY PRACTICES
YOU ARE RESPONSIBLE for the safe assembly
of the machine.
DO NOT ALLOW CHILDREN or other unauthorized
persons within the assembly area.
WEAR PERSONAL PROTECTIVE EQUIPMENT
which includes a hard hat, eye protection, work
gloves and steel toed boots with slip resistant
soles.
DO NOT MODIFY the equipment or substitute parts
in any way. Unauthorized modication may impair
the function and/or safety of the machine.
USE SUITABLE LIFTING DEVICE for components
which could cause personal injury.
BLOCK UPANY RAISED PART of the machine. Be
sure machine is stable after blocking.
ALWAYS INSPECT LIFTING CHAINS AND
SLINGS for damage or wear.
BE SURE LIFTING DEVICE IS RATED TO
HANDLE THE WEIGHT.
STOP ENGINE, place all controls in neutral,
set parking brake, remove ignition key and
wait for all moving parts to stop before serving
or adjusting.
BE SURE PRESSURE IS RELIEVED from
hydraulic circuits before servicing or discon-
necting from tractor.
USE EXTREME CARE when servicing or
adjusting.
GENERAL ASSEMBLY INSTRUCTIONS
1. READ AND UNDERSTAND Operator’s Manual before assembly of machine.
2. Reference to “RIGHT” and “LEFT” is determined when machine IS VIEWED FROM THE REAR.
3. Reference to “FORWARD” means TOWARDS THE TRACTOR.
4. Reference to “REAR” means AWAY FROM THE TRACTOR.
DISK MOUNTED HARROW INSTALLATION GUIDE
Disk brackets and Spacer Tubes for M94 through M108 Mounted Harrow
See Pages 2.05 – 2.07 of Whole Goods Catalog for Sections Required
Use one short disk bracket with sections supported by one mounting arm. Use two short disk brackets to
mount a single harrow section across disk center. At locations other than disk center, a combination of brack-
ets and spacers (listed below) are required to attach mounted harrows to an angled implement frame.
Section First Choice Second Choice
Cross Tube
Model Width Length Brckt. 1 Brckt. 2 (C) Distance (D) Brckt. 1 Brckt. 2 (C) Distance (D)
M94 4 ½’ 16” Short Short +3” 8-9” Short Short +2” 7 –7 ½”
M94 6’ 34” Short Short +4” 11-14” Short Short +3” 8 – 9”
M94 7 ½’ 52” Short Long +3” 44 ½ -45” Short Long +2” 41 ½-44 ½”
M104/M108 6’ 23 ½” + 15” Short Long 35 ½” Short Short +4” 11 – 14”
M104/M108 8’ 47 ½” Short Long 35 ½-38 ½” Short Short +4” 11 – 14”
M104/M108 10’ 71 ½” Short Long +4” 47 ¾ -50 ¾” Short Long +3” 44 ½-47 ½”
UNIVERSAL DISK BRACKETS
HIGH CLEARANCE DISK BRACKETS
6
Section
Cross Tube First Choice Second Choice
Model Width Length Brckt. 1 Brckt. 2 (C) Distance (D) Brckt. 1 Brckt 2. (C) Distance (D)
M94 4 ½’ 16” Short Short +3” 8-9” Short Short +2” 7 –7 ½”
M94 6’ 34” Short Long 26 ¼ - 27” Short Short +4” 11 – 14”
M94 7 ½’ 52” Short Long +4” 38 ½ - 41 ½” Short Long +3” 35 ½ -38 ½”
M104/M106 6’ 23 ½” + 15” Short Long 26 ¼ – 29 ½” Short Short +4” 11 – 14”
M104/M106 8’ 47 ½” Short Long +4” 38 ½ - 41 ½” Short Long +3” 35 ½-38 ½”
M104/M106 10’ 71 ½” Short Long +4” 38 ½ - 42 ½ ” Short Long +3” 35 ½-38 ½”
C) Spacer Tubes W/Hardware 2” = 8H1500 4” = 8H1505
3” = 8H1503
D) Approximate centerline to centerline of Mounting Arms (8H2310) based on 18 degree rear gang angle
A
MH MNTNG ARM ASSY5/22/2018 8H2314.iam/
8X0073
1/2 X 5"
8X0123
3/4" X 5.5"
8X0099
5/8" X 6-3/4"
8X0304
5/8" LW
8X0250
5/8" N
8X0261
3/4" LN 8X0242
NY-LOCK 1/2" N
8X0118
3/4 X 4"
8X0014
1/4 X 3"
8X0222
1/4" LN
8X0261
3/4" LN
8H2190
8H1280
ARM LENGTH
8H2132 - 34"
8H2142 - 42"
8H2144 - 52"
FRAME SIZES
WING-ARM TRAVEL STOP
MATCH LOCATION LETTER
ON SUPPORT ROD ASSEMBLY
WING-ARM TRAVEL STOP
DO NOT OVERTIGHTEN
ARM MUST BE FREE TO ROTATE
C
B
A
ABC
8Z0101
SMC DECAL
8X0306
3/4" LW
8X0117
3/4 X 7"
3"
4"
5"
6"
2 1/2"
8H1394
8W1897
8H1315
8D5219
8H1309
8H1328
8X0269
8X0101
5/8" X 8"
NOT RQRD
WITH
DISK
BRACKET
8H1520 SHORT UNIVERSAL
8H1522 SHORT HI-CLEARANCE
8H1530 LONG UNIVERSAL
8H1532 LONG HI-CLEARANCE (SHOWN)
8X0099
5/8" X 6-3/4"
8X0304
5/8" LW
8X0250
5/8" N
8H1510
8H2295
FILLER
FOR BEHIND
8T4100
8H2184
8H2100
8W1205
5/8 x 3-1/16 x 3-1/4"
8X0256
5/8" FLNG NUT
8H2129
8H2131A
SPRING
URETHANE BUSHING
OR
8H2128
8X0338
8X0268
8H2129
8H2125
7
8
9
10
3BR M104
11/14/2013 8HD5361.iam/
8X0242
NY-LOCK 1/2" N
8X0079
1/2" X 4-1/8"
8X0240
1/2" N
8HD5180
8X0240
1/2" N 8X0303
1/2" LW
8HD5101
8X0066
1/2 X 1-3/4"
8X0242
NY-LOCK 1/2" N
8X0067
1/2-13NCX2-1/4"
8X0242
NY-LOCK 1/2" N
8X0242
NY-LOCK 1/2" N
8X0520
ROLL PIN
8X0323
5/8" FW
8HD0160
8HD0150
8X0066
1/2 X 1-3/4"
8HD0200
8HD5115
8X0063
1/2 X 1-1/2"
8HD5102
6', 8' & 10' 3 BAR SECTION ASSEMBLY MODEL 104-108
8H1180S (1/2 X 20")
8H1184S (1/2 X 26")
8H1190S (9/16 X 26")
8H1195S (5/8 X 28")
8HD5056Q - 6' (01- )
8HD5056 - 6' ( -00)
8HD5076Q - 8' (01- )
8HD5076 - 8' ( -00)
8HD5086Q - 10' (01- )
8HD5086 - 10' ( -00)
8HD5054 - 6'
8HD5074 - 8'
8HD5084 - 10'
8HD5052 - 6' (61-1/2")
8HD5072 - 8' (85-1/2")
8HD5082 - 10' (109-1/2")
8Z0114
M104 DECAL
8Z0115
M105 DECAL
8Z0118
M106 DECAL
8Z0119
M108 DECAL
(OPTIONAL)
(LEFT)
8HD5140 - 6' (23-3/8")
8HD5150 - 8' (47-3/8")
8HD5160 - 10' (71-3/8")
8HD0080
(RIGHT)
11
4BR M10411/7/2011 8hd5365.iam/
6, 8' & 10' 4 BAR SECTION ASSEMBLY MODEL 104-108
8X0079
1/2" X 4-1/8"
8X0242
NY-LOCK 1/2" N
8HD0080
8X0303
1/2" LW
8X0240
1/2" N
8X0303
1/2" LW
8X0330
1/2" FW 8HD5105
8X0066
1/2 X 1-3/4"
8X0242
NY-LOCK 1/2" N
8HD5115
8X0242
NY-LOCK 1/2" N
8HD0150
8HD0160
8X0323
5/8" FW
8X0520
ROLL PIN
8HD5106
8X0063
1/2 X 1-1/2"
8X0067
1/2-13NCX2-1/4"
8HD5120
8Z0114
M104 DECAL
8Z0115
M105 DECAL
8Z0118
M106 DECAL
8Z0119
M108 DECAL
8H1180S (1/2 X 20")
8H1184S (1/2 X 26")
8H1190S (9/16 X 26")
8H1195S (5/8 X 28")
8HD5140 - 6' (23-3/8")
8HD5150 - 8' (47-3/8")
8HD5160 - 10' (71-3/8")
(LEFT)
(RIGHT)
8HD5058Q - 6' (01- )
8HD5058 - 6' ( -00)
8HD5078Q - 8' (01- )
8HD5078 - 8' ( -00)
8HD5088Q - 10' (01- )
8HD5088 - 10' ( -00)
8HD5057 - 6'
8HD5077 - 8'
8HD5087 - 10'
8HD5054 - 6'
8HD5074 - 8'
8HD5084 - 10'
8HD5052 - 6' (61-1/2")
8HD5072 - 8' (85-1/2")
8HD5082 - 10' (109-1/2")
8HD5180
(OPTIONAL)
19
1
/
4
"
16
1
/
2
"
21
3
/
4
"
14
"
8HD0202
8HD0200
MNT HRW DISK BRCKTS
1/14/2009
8H1610
DISK BRCKT LONG
W/PLATE - UNIVERSAL
8H1600
DISK BRCKT SHORT
W/PLATE - UNIVERSAL
8H1612
DISK BRCKT LONG
W/PLATE - HIGH CLEARANCE
8H1602
DISK BRCKT SHORT
W/PLATE - HIGH CLEARANCE
8X0250
5/8" N
8X0304
5/8" LW
8H1510
8H1520
8H1530
8H1510
8H1532
8H1510
8H1522
8H1510
8X0250
5/8" N
8X0304
5/8" LW
8X0250
5/8" N
8X0304
5/8" LW
SPACER TUBES
8H1499 (TUBE ONLY - 2")
8H1498 (TUBE ONLY - 3")
8H1504 (TUBE ONLY - 4")
8H1500 (2" W/HRDWR)
8H1503 (3" W/HRDWR)
8H1505 (4" W/HRDWR)
BOLT FOR SPACER TUBE
8X0096 (5/8" X 4")
8X0095 (5/8" X 5")
8X0099 (5/8" X 6.75")
(6" MAX. FRAME)
8H1512 (11" MAX. OPT.)
(6" MAX.)
8H1512 (11" MAX. OPT.)
(6" MAX.)
8H1512 (11" MAX. OPT.)
(6" MAX.)
5/8" BOLT LENGTH
AS REQUIRED
8X0093
5/8" X 2"
8X0304
5/8" LW
8X0250
5/8" N
12
JD 510/512 DISK RIPPER WITH SUMMERS HARROWS
1. Bolt extensions to 510 main frame as shown (ush side down).
2. U-bolt 4X4 to extensions (center on machine).
3. Bolt arms to 4X4 tube.
4. U-bolt sections to arms. (Leave 12” gap in the center, between tines.)
13
WIDTH SECTIONS
REQRD 8H2310 8HD5250 8H1600 8H1505 M104 M106
CNTR
SECT WING ARM MNTNG
PKG
DISK
BRCKT
SPACER,
4”
5 Shank /
12 1/2’ Width 2: 8’ –– 4 1 –– ––
2 - 8HD5381
4 - 8H2310
1 - 8HD5250
2 - 8HD5387
4 - 8H2310
1 - 8HD5250
7 Shank /
17 1/2’ Width 2: 10’ –– 4 1 –– ––
2 - 8HD5401
4 - 8H2310
1 - 8HD5250
2 - 8HD5407
4 - 8H2310
1 - 8HD5250
9 Shank /
22 1/2’ Width
1: 6’ and
1: 8’
6’
(EA) 8 1 4
(WING)
2
(WING)
3 - 8HD5361
1 - 8HD5381
8 - 8H2310
1 - 8HD5250
4 - 8H1600
2 - 8H1505
3 - 8HD5367
1 - 8HD5387
3 - 8H2310
1 - 8HD5250
4 - 8H1600
2 - 8H1505
13A
13B
13C
14
Some tillage implements have close to 180 degrees of wing travel into transport position. Machines like this include
short wing machines with low transport height and 5 section machines (outside wings only). This type of fold
can cause interference problems with SMC Mounted Harrows. The following are steps to prevent problems:
MODEL 74:
1. If mounting brackets/arms hit in transport position, one of the 2 interfering brackets/arms must be moved.
2. If sections hit in transport position, limit travel of top section by:
a. Slide and secure lock collar down support rod a maximum of 3”.
or
b. Replace standard 8H1308 pressure spring with 8H1306.
or
c. Add third mounting arm assembly.
MODEL 94 through 106:
1. If mounting brackets/arms hit in transport position, one of the 2 interfering brackets/arms must be moved.
2. If sections hit in transport position, limit travel of top section by:
a. Slide and secure lock collar down support rod a maximum of 2.5”.
or
b. Add second mounting arm assembly.
or
c. Install travel limit 1/2” x 5” stop bolts* (8X0073) in mounting brackets (8H2120). Secure stop bolt
with 1/2” lock nuts (8X0242), do not over tighten, mounting arm MUST be free to rotate on pivot bolt.
*Stop bolts should be used as a last resort. Extensive frame damage could occur if stop bolts are incorrectly
installed or if eld obstruction causes mounted harrow section to exceed travel limit.
ALWAYS raise machine slowly into transport position the rst time after installing Mounted Harrows, watch for
interference and make adjustments as required.
MOUNTING
INSTRUCTIONS
FOR SUMMERS
Mounted Harrows
on Cultivators, Chisel Plows and Disk
This manual suits for next models
4
Other Summers Lawn And Garden Equipment manuals
