Summit Treestands SU81547 User manual

FORM# 81547 - 4/16PRINTED IN CHINA
Roof and Blind Kit for Strike Pod Tripod
PN SU81547
© 2016 Summit Treestands, LLC | 715 Summit Dr. Decatur, AL 35601
PH#: [phone] | www.summitstands.com
WARNING
!
FAILURE TO READ AND FOLLOW ALL MANUFACTURER’S
WARNINGS AND INSTRUCTIONS CONSTITUTES A MISUSE OF THIS
PRODUCT AND COULD RESULT IN SERIOUS INJURY OR DEATH!!
• READ, FOLLOW AND UNDERSTAND ALL WRITTEN AND VIDEO WARNINGS AND INSTRUCTIONS BEFORE USE. INSPECT ALL EXPIRATION TAGS
PRIOR TO EACH USE. IF YOU DON’T COMPLETELY UNDERSTAND SAFE AND PROPER USE OF THE FULL BODY FALL ARREST HARNESS
SYSTEM (FBFAHS) OR TREESTAND, HUNT FROM THE GROUND! FAILURE TO FOLLOW ALL WARNINGS AND INSTRUCTIONS LISTED COULD
RESULT IN SERIOUS INJURY OR DEATH!
• WHEN HUNTING FROM A TREESTAND, FALLS CAN OCCUR ANY TIME AFTER LEAVING THE GROUND! ANY FALL CAN CAUSE SERIOUS INJURY
OR DEATH!
• DO NOT USE THIS PRODUCT UNTIL YOU UNDERSTAND SAFE AND PROPER USE. READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS
PRIOR TO EACH USE!
• SPRING STEEL COILS ARE UNDER PRESSURE. OPEN WITH EXTREME CAUTION. SPRING STEEL COILS WILL DEPLOY AND UNCURL ONCE THE
RETENTION CLAMPS HAVE BEEN REMOVED WHICH MAY CAUSE SERIOUS INJURY. ENSURE NO-ONE IS YOUR PROXIMITY WHEN OPENING.
• ALWAYS ANCHOR YOUR TRIPOD BEFORE INSTALLING THIS PRODUCT.
• DO NOT USE THIS PRODUCT IN ANY ADVERSE WEATHER CONDITIONS.
(A) Warranty
Summit Treestands, LLC (Summit) warrants to the original retail purchaser that all products manufactured by it are free from defects in
material and manufacture at the time of shipment for twelve (12) months from the date of purchase. Summit will replace any part found
defective if the unit claimed to be defective shall be returned to Summit, postage prepaid, within the warranty period.
This warranty shall not apply to any product which has been subjected to misuse; misapplication; neglect (including but not limited to
improper maintenance); accident; improper installation; modification (including but not limited to use of unauthorized parts or attachments);
adjustment or repair. THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED (INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS OF ANY PRODUCT FOR A PARTICULAR PURPOSE), AND OF ANY OTHER OBLIGATION OF LIABILITY ON THE
PART OF THE COMPANY.
(B) Limitation of Liability
It is expressly understood that Summit’s liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise,
is limited to the repair of the product, as stated above, and Summit will not be liable for any other injury, loss, damage, or expense, whether
direct or consequential, including but not limited to loss of use, income, profit, or damage to material, arising in connection with the sale,
installation, use of, inability to use, or the repair or replacement of Summit’s products.
Summit reserves the right to make alterations or modifications in its products at any time, which in its opinion, may improve the
performance and efficiency of the product. It shall not be obligated to make such alterations or modifications to products already in service.
LIMITED WARRANTY
1

PG 2 www.summitstands.com
ASSEMBLY
2
1. Attach the rod brackets to the outside of each corner of the
tripod frame as shown in figure 1. Secure with one nut and bolt.
2. Open the spring steel coils by sliding the ends out of the
retention clamp. Be careful, keep away from your face as the
ends of the coil will spring open as they are under tension. Make
sure any other persons are clear of the area before opening the
coil.
3. Put the ends of the spring steel in the rod bracket in opposite
corners forming an arc that crosses in the middle. See figure 2.
4. Stand on the platform facing out toward the ladder. Start
with the roof section of the blind first (the roof will have the
windows in it). Locate the two large pieces of Velcro on one
corner as shown in figure 3. Keep these on your left side as they
will need to be on the left corner of the tripod frame.
5. With the camo facing up, pull the roof up and over the spring
steel rods and line up the seams of the roof with the spring steel
frame as shown in figure 4. Rap the Velcro strips around the four
corners of the tripod frame to hold the roof in place as shown in
figure 5. Attach the Velcro strip at the center top the blind to the
cross section of the spring steel. See figure 6.
Rod Bracket
1
2
3 4
Spring Steel
5
Velcro Strap
6
WARNING
!
SPRING STEEL COILS ARE UNDER PRESSURE. OPEN WITH
EXTREME CAUTION. SPRING STEEL COILS WILL DEPLOY
AND UNCURL ONCE THE RETENTION CLAMPS HAVE BEEN
REMOVED WHICH MAY CAUSE SERIOUS INJURY. ENSURE
NO-ONE IS YOUR PROXIMITY WHEN OPENING.

PG 3
6. Next, move to the bottom skirt of the blind and locate the
end that has the three Velcro straps down the side. Rap them
around the railing upright tube on the left side of the tripod
frame as shown in figure 7.
7. Pull the skirt around to all four corners attaching the large
Velcro patches to the Velcro patches on the roof. Pull the skirt
tight as you work your way around the tripod frame. See figure
8. The velcro patches should line up as you move around.
8. You will notice that there are three Velcro straps on each of
the four section of the tripod frame. Rap these straps around the
frame including the lower part of the window as shown in figure
9. This will secure the blind skirt and roof to the tripod frame.
See figure 10.
9. Pull the bottom of the skirt down around the base of the
platform and attach the S-hook in the corner of the tripod frame
as shown in figure 11. This will secure the base of the skirt to the
platform.
7
8 9
10 11

PG 4 www.summitstands.com