Sun Bandit SB-30E-100200-3000 Service manual

Solar Hybrid Energy Systems • Patent(s) Pending
Solar Hybrid Energy Systems • Patent(s) Pending
Solar Hybrid Energy Systems • Patent(s) Pending
Sun Bandit® Hybrid Water Heater
Installation and Operation
Instruction Manual
IMPORTANT!
Record all product serial numbers BEFORE installing
your Sun Bandit® Solar Hybrid Energy System
Solar Hybrid Energy Systems • Patent(s) Pending
Solar Hybrid Energy Systems • Patent(s) Pending
Solar Hybrid Energy Systems • Patent(s) Pending
sunbandit.us
Sun Bandit® is a registered trademarks of Next Generation Energy® ©2013 Next Generation Energy® All rights reserved. #23460 Rev 1 6/2013

Page 1
IMPORTANT!
Record all product serial numbers BEFORE installing your Sun Bandit® Solar
Hybrid Energy System. You will need this information to complete the online
Warranty Registration of your Sun Bandit® Solar Hybrid Energy System and for
the warranty to be valid. See page 20 for more information.
To the Consumer:
Please read these and all component
instructions and keep for future reference.
To the Installer:
Please attach these instructions
next to the water heater.
WARNING
Improper installation, adjustment, alteration,
service or maintenance can cause serious
injury or property damage. Refer to this
manual. For assistance or additional
information, consult a qualified installer or
service agency.
CAUTION
The recommended water temperature for
normal residential use is 120°F/49°F. A
thermostatic mixing valve is supplied and
must be installed to the water heater. Follow
the instructions supplied with the mixing
valve to obtain a mixed water temperature of
120°F. Measure water temperature at the tap
nearest to the water heater.
WARNING
Hotter water increases the risk of scald injury.
Before adjusting the water temperature setting,
read this instruction manual. Temperatures at
which injury occurs vary with the person’s age
and the length of exposure.
The slower reaction time of children, elderly,
and physically or mentally challenged persons
increases the scalding hazard to them. It is
recommended that lower water temperatures
be used where these exposure hazards exist.
Such households may require a temperature
setting less than 120°F to prevent accidental
contact with hot water.
To lower water temperature use point-of-use
temperature limiting devices.
WARNING
Water heater blankets are not recommended
and will void the warranty.
THIS MANUAL HAS BEEN PREPARED
TO ACQUAINT YOU WITH THE INSTALLATION,
OPERATION, AND MAINTENANCE OF
YOUR WATER HEATER AND TO PROVIDE
IMPORTANT SAFETY INFORMATION.
INSTALLER RESPONSIBILITIES
Please read all instructions thoroughly before
installing or placing the heater into service.
This unit must be installed by licensed or
authorized installers, or technical personnel
that service water heating equipment. The
heater must be installed in accordance with all
local codes and ordinances.
FAILURE TO FOLLOW THESE INSTRUCTIONS
OR ALL APPLICABLE BUILDING CODES AND
REGULATIONS VOIDS THE WARRANTY
ON THIS WATER HEATER.
Local plumbing and electrical codes must
be followed in the installation of this water
heater. In the absence of a local code use the
UNIFORM PLUMBING CODE and the NFPA 70
Code. Local codes may supersede instructions
in this installation manual.
These instructions are a guide for the
correct installation of the water heater.
The manufacturer will not be liable for
damages caused by failure to comply with
the installation and operating instructions
outlined on the following pages.
HANDLING
Before uncrating, check for shipping damage.
Report any damage to your carrier. Note damage
on bill of lading or delivery receipt and file a
claim.

Page 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
When using electrical appliances, basic safety precautions to reduce the
risk of fire, electric shock, or injury to persons should be followed, including:
1. READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.
2. This water heater must be grounded. Connect only to properly
grounded outlet. See “GROUNDING INSTRUCTIONS” found on page 13.
3. Install or locate this water heater only in accordance with the provided
installation instructions.
4. Use this water heater only for its intended use as described in this
manual.
5. Do not use an extension cord set with this water heater. If no receptacle
is available adjacent to the water heater, contact a qualified electrician
to have one properly installed.
6. As with any appliance, close supervision is necessary when used by
children.
7. Do not operate this water heater if it has a damaged cord or plug, if it is
not working properly, or if it has been damaged or dropped.
8. This water heater should be serviced only by qualified service
personnel. Contact nearest authorized service facility for examination,
repair, or adjustment.
SAVE THESE INSTRUCTIONS

Page 3
TABLE OF CONTENTS
Section I: Specifications .............................................4
Section II: General Information ....................................... 5
Section III: Pre-Installation ...........................................8
Section IV: Installation ..............................................9
Section V: Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section VI: Maintenance ........................................... 15
Section VII: Troubleshooting......................................... 16
Section VIII: Parts List .............................................. 17
Section IX: Warranty ............................................... 19

Page 4
SECTION I: SPECIFICATIONS
Model designations that contain “100200” denote Sun Bandit®AC Micro-Grid Resistive Elements operate non-
simultaneously.
Model designations that contain “300400” denote Sun Bandit®AC Micro-Grid Resistive Elements can operate
simultaneously (if call for heat exists at each Sun Bandit®AC Micro-Grid Resistive Element thermostat).
Model designation suffix “3000” denotes maximum power rating (W) of each Sun Bandit® AC Micro-Grid Resistive Element.
SB-30E-100200-3000 20´´ 39 1⁄2´´ 33´´ 33´´ 4 5⁄8´´
SB-30E-300400-3000 20´´ 39 1⁄2´´ 33´´ 33´´ 4 5⁄8´´
SB-50E-100200-3000 22´´ 48 1⁄4´´ 39 3⁄4´´ 39 3⁄4´´ 4 1⁄2´´
SB-50E-300400-3000 22´´ 48 1⁄4´´ 39 3⁄4´´ 39 3⁄4´´ 4 1⁄2´´
SB-80E-100200-3000 24´´ 64´´ 57 1⁄8´´ 57 1⁄8´´ 5´´
SB-80E-300400-3000 24´´ 64´´ 57 1⁄8´´ 57 1⁄8´´ 5´´
Model
A C
B
E
D
Dimensions
Table 1: Dimensions
Figure 1: SB-30E, SB-50E, SB-80E

Page 5
SECTION I: SPECIFICATIONS (cont.)
SECTION II: GENERAL INFORMATION
SUN BANDIT®HYBRID WATER HEATER FUNCTION
The Sun Bandit®Hybrid Water Heater is designed to heat water with electric resistance
heating elements that are powered from two different sources, 1) electricity generated by the
Sun Bandit®AC Micro-Grid (i.e. PV modules plus Sun Bandit®AC Micro-Grid Inverter) and
2) standard utility power. Sun Bandit®AC Micro-Grid resistive elements are located in the
tank such that all stored water could be heated from solar energy. A standard utility powered
element is located to ensure 50% of the stored water is always heated.
All models include two Sun Bandit®AC Micro-Grid Resistive Elements. Models that contain
“100200” in the model designation are wired such that the two AC Micro-Grid Resistive
Elements cannot operate simultaneously. For these models, the upper resistive element has
priority. Models that contain “300400” in their designation contain AC Micro-Grid Resistive
Elements that are electrically isolated and can operate simultaneously provided there is a
demand for heat at the respective thermostats.
Power availability from the Sun Bandit®AC Micro-Grid will vary depending on outside
conditions.
WATER TREATMENT & FILTRATION
In areas where poor water conditions are suspected (i.e. lime, iron, and other minerals), it
is essential that the water be tested and appropriate action taken to prevent damage to the
water heater and ensure the quality of the water.
SB-30E-100200-3000 30 7.5 3.0 N 4.5
SB-30E-300400-3000 30 10.5 3.0 Y 4.5
SB-50E-100200-3000 50 7.5 3.0 N 4.5
SB-50E-300400-3000 50 10.5 3.0 Y 4.5
SB-80E-100200-3000 80 7.5 3.0 N 4.5
SB-80E-300400-3000 80 10.5 3.0 Y 4.5
Model
Rated Storage
Capacity (gal)
Rated Maximum Input
(kW)
(All Resistive Elements)
AC Micro-Grid
Element Rating (kW)
AC Micro-Grid
Elements Simultaneous
Operation? (Y/N)
Standard Utility
Powered Element
Rating (kW)
Table 2: Inputs and Capacities

Page 6
SECTION II: GENERAL INFORMATION (cont.)
TEMPERATURE CONTROL
The Sun Bandit®Hybrid Water Heater is equipped with resistive elements and adjustable
thermostats. If the solar system cannot satisfy the user demand, the standard utility powered
resistive element will energize and heat the water until its thermostat is satisfied. An ECO
(electrical cut-off) is included as part of the temperature control and is designed to cut off
power to the heating element in the event the water in the tank reaches 180°F. The ECO is a
safety feature on the water heater and cannot be adjusted. In the event that the ECO opens,
the control must be manually reset with the stored water temperature below 180°F.
The Sun Bandit®AC Micro-Grid Resistive Element thermostats are factory set to 120°F. The
standard utility power thermostat is also factory set to 120°F. See Table 6 for thermostat letter
and temperature relationships. Setting the temperature on the AC Micro-Grid thermostats
higher than the standard utility power thermostat will allow the system to maximize water
heating from solar energy.
THE THERMOSTATIC MIXING VALVE THAT IS SUPPLIED WITH THIS WATER
HEATER MUST BE INSTALLED PER THE VALVE MANUFACTURER’S INSTRUCTIONS.
Water temperatures in the tank will exceed 120°F. The supplied mixing valve must be
installed to the Sun Bandit®Hybrid Water Heater and adjusted to a safe temperature. The
recommended water temperature for normal residential use is 120°F. Table 3 details the
approximate relationship of water temperature and time with regard to scald injury. Measure
water temperature at the tap nearest to the water heater and adjust the mixing valve
according to the valve manufacturer’s instructions.
APPROXIMATE
TEMPERATURE/TIME
RELATIONSHIPS TO
SCALDING
120°F More than 5 minutes
125°F 1
1⁄2 to 2 minutes
130°F About 30 seconds
135°F About 10 seconds
140°F Less than 5 seconds
145°F Less than 3 seconds
150°F About 1 1⁄2 seconds
155°F About 1 second
Table 3: Scald Temperature/Time Relationships

Page 7
SECTION II: GENERAL INFORMATION (cont.)
ANODE RODS
The anode rod is used as a sacrificial element within the volume of the storage tank. The
purpose of the magnesium anode rod is to protect the inside of the tank against corrosion.
Anode rods should be inspected twice in the first year and at least yearly once a time interval
for inspection has been developed. Water conditions will influence the consumption rate of
the anode rods. Please see the Maintenance section of this manual for instructions on how to
change the anode rods in your water heater.
CAUTION
Hydrogen gas is produced in a hot water system served by the heater that has not
been used for a long period of time (2 weeks or more). Hydrogen gas is extremely
flammable. To reduce the risk of injury under these conditions, it is recommended
that the hot water faucet be opened for several minutes at the kitchen sink before
using any electrical appliance connected to the hot water system. When hydrogen
is present, there will probably be an unusual sound such as air escaping through the
pipe as the water begins to flow. There should be no smoking or open flame near the
faucet at the time it is open.
TEMPERATURE AND PRESSURE RELIEF VALVE (T&P)
CAUTION
To reduce the risk of excessive pressures and temperatures in this water heater, install
temperature and pressure protective equipment required by local codes and no less
than a combination temperature and pressure relief valve certified by a nationally
recognized testing laboratory that maintains periodic inspection of production of listed
equipment or materials, as meeting the requirements for Relief Valves and Automatic
Gas Shutoff Devices for Hot Water Supply Systems, ANSI Z21.22. This valve must be
marked with a maximum set pressure not to exceed the marked maximum working
pressure of the water heater. Install the valve in an opening provided and marked for
this purpose in the water heater, and orient it or provide tubing so that any discharge
from the valve exits only within 6 inches above, or at any distance below, the
structural floor, and does not contact any live electrical part. The discharge opening
must not be blocked or reduced in size under any circumstances.
The T&P valve is factory installed. A discharge drain tube must be installed (responsibility
of the installer) and shall terminate plain, not threaded, 6 inches above the floor drain.
The drain tube material must be approved for temperatures of 120°F or greater and a
pressure of 150 PSI or greater.
BACKFLOW PREVENTER (CLOSED LOOP SYSTEM)
Some local municipal codes and ordinances require the use of these devices on potable
(domestic) water lines. Where backflow preventers are required, it will be necessary to install
a thermal expansion tank (designed for used with potable water) in order to prevent
pressure build up in the water heater and associated piping, which could cause the T&P valve
to discharge. Follow the expansion tank manufacturer’s recommendations when selecting a
tank for your hot water system.
Note: Working pressure of the water heater is 150 PSI. Do not exceed 150 PSI.

Page 8
SECTION III: PRE-INSTALLATION
LOCATION
CAUTION
This water heater must be located in an area where leakage of the tank, water line
connections, or the temperature and pressure relief valve will not result in damage to
the area adjacent to the water heater or to lower floors of the structure. When such
location cannot be avoided, a suitable drain pan must be installed under the water
heater. The drain pan depth must be suitable for draining and collecting water. The
drain pan can be purchased from your plumbing professional. The drain pan must
be piped to an adequate drain and all drain piping must be at least 0.75” in diameter
and pitched for proper drainage.
CAUTION
DO NOT store or use gasoline or other flammable, combustible, or corrosive vapors
and/or liquids in the vicinity of the water heater or any other appliance.
IF YOU SMELL GAS:
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any telephone in your building.
• Immediately call your gas supplier from a telephone in another building. Follow your
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
DO NOT OPERATE THE APPLIANCE UNTIL THE LEAKAGE IS CORRECTED!
CAUTION
Do not drop water heater or lay heater down on its side. Move the water heater into
position by sliding or using an appropriately sized hand truck.
The Sun Bandit®Hybrid Water Heater must be installed indoors. Locate the water heater as
close as practical to the Sun Bandit®AC Micro-Grid system and leave sufficient clearances for
servicing the heater. This water heater may be installed on combustible flooring. DO NOT
install this water heater on carpeting.
See Tables 4 and 5 for combustible and service clearances.
Top Sides Front Rear
0´´ 0´´ 0´´ 0´´
Top Sides (non-piping) Side (T&P Relief Valve) Front Rear
12´´ 4´´ 6´´ 16´´ 0´´
Table 4: Clearance from Combustible Materials
Table 5: Recommended Service Clearances

Page 9
SECTION IV: INSTALLATION
WATER CONNECTIONS
CAUTION
This water heater incorporates fittings that contain a nonmetallic lining. DO NOT apply
heat to these fittings when making sweat connections to the heater. Sweat tubing to
an adapter before securing adapter to any fittings on water heaters.
ALL PIPING SHOULD CONFORM TO LOCAL CODES AND ORDINANCES. It is highly
recommended that unions and shut-off valves are installed at the potable water connections
to allow for isolation and/or movement during service. Installing a union on the potable
outlet is of particular importance to facilitate replacement of the hot outlet/anode nipple on
all models. In addition, all piping should be adequately insulated with an approved material
to minimize heat loss.
POTABLE WATER CONNECTIONS
THE WATER HEATER MUST BE FILLED WITH WATER BEFORE CONNECTING
ELECTRIC POWER.
1) Close the main water supply valve before continuing with the installation. After the
main water supply is shut-off, relieve the water line pressure by opening a faucet. Once the
pressure has been relieved, close the faucet. The “Cold” and “Hot” potable water connections
are labeled on the water heater. Install the supplied thermostatic mixing valve to the “Cold”
and “Hot” connections on the top of the water heater. Follow the instructions that are
supplied with the mixing valve.
2) Install a union and shut-off valve on both the cold and hot water sides of the water heater.
3) If a backflow preventer is required in the cold water supply, a properly sized expansion
tank must be installed to control thermal expansion. Do not operate the water heater in
a closed system without installing a thermal expansion tank. Follow the expansion tank
manufacturer’s recommendations when selecting a tank for your system.
4) Following installation of the water lines, open the main water supply valve and fill the
water heater. Open several hot water faucets to relieve air from the system. After water is
flowing through the faucets and the system is void of air, close the faucets and check for
water leaks in the system.

Page 10
SECTION IV: INSTALLATION (cont.)
A piping diagram for the Sun Bandit®Hybrid Water Heater is shown in Figure 2.
ELECTRICAL CONNECTIONS
DANGER
Confirm that all electrical connections are unpowered before installing or servicing
electrical components/connections within the water heater.
WARNING
The water heater must be electrically grounded in accordance with local codes or, in
the absence of local codes, with NFPA 70.
Failure to properly wire electrical connections may result in serious physical harm.
Electrical power may be from more than one source. Make sure all power is off before
attempting any electrical work.
Figure 2: Water Connections
PIPINg dIAgRAmS

Page 11
RESISTIVE ELEmENTS
THE WATER HEATER MUST BE FILLED WITH WATER BEFORE CONNECTING
ELECTRIC POWER.
All electrical connections on the water heater must be made with copper conductors only.
A separate branch circuit with copper conductors, over-current protection, and means for
disconnection must be provided by qualified service personnel. The total wattage load and
voltage requirements for the water heater are specified on the rating label located on the
front of the heater.
The thermostats and resistive elements are pre-wired at the factory. Junction boxes are
located at the top of the water heater. The junction box cover will accommodate a 1/2” or
3/4” electrical conduit connector. Three wires are located in the junction box (red, black,
and green) for connection to the supply circuit. See Figures 3-5 for wiring diagrams.
gROuNdINg INSTRuCTIONS
A green screw (ground) is located in the junction box for proper connection to ground from
the branch circuit.
BRANCH CIRCuIT SIZINg ANd WIRE SIZE
Table 6 provides recommendations for minimum branch circuit sizing and wire size based
on the National Electric Code (NFPA 70). For field wiring connections in each junction box,
reference Figures 3-5.
SECTION IV: INSTALLATION (cont.)
3,000 20 20 15 15 12 12 14 14
4,000 25 25 20 15 10 10 12 14
4,500 30 25 25 15 10 10 10 14
5,000 30 30 25 15 10 10 10 14
5,500 35 30 25 15 8 10 10 14
6,000 40 35 30 20 8 8 10 12
8,000 50 45 40 25 8 8 8 10
9,000 - 50 45 25 - 8 8 10
10,000 - - 50 30 - - 8 10
11,000 - - 50 30 - - 8 10
12,000 - - - 35 - - - 8
208V
Recommended Over-Current
Protection (fuse or circuit
breaker amperage rating)
Table 6: National Electric Code - Branch Circuit Sizing and Wire Size
Total Water
Heater Wattage
Copper Wire Size (AWG)
240V
277V
480V
208V
240V
277V
480V

Page 12
Figure 3: Standard Utility Circuit Wiring Diagram
(All models)
Figure 4: AC Micro-Grid Circuit Wiring Diagram
(for model designations that contain “100200”)
SECTION IV: INSTALLATION (cont.)
Wiring diagrams are shown in Figures 3-5.

Page 13
Figure 5: Upper or Lower AC Micro-Grid Circuit Wiring Diagram
(for model designations that contain “300400”)
SECTION IV: INSTALLATION (cont.)

Page 14
SECTION V: OPERATION
THERMOSTAT TEMPERATURE ADJUSTMENT
CAUTION
The temperature setting on the heating element thermostat shall not exceed 160°F.
The thermostatic mixing valve supplied with this water heater must be installed to
reduce the risk of scalding.
CAUTION
Turn off all power to the water heater before adjusting the heating element thermostat.
All thermostats are factory adjusted to 120°F (“HOT” indicator setting). If thermostat
adjustment is necessary, disconnect all power to the water heater. Remove the access cover
on the side of the water heater and remove the foam dam insert to expose the thermostat and
heating element. The temperature knob can be adjusted with a screwdriver to a minimum
temperature of 110°F and a maximum temperature of 160°F (labeled “VERY HOT”). See
Table 6 for a listing of indicator setting and temperature relationships.
CAUTION
Hot water in excess of 120°F can cause scalding! The temperature at which injury
occurs varies with the person’s age and the time of exposure. The slower response
time of disabled persons increases the hazards to them. NEVER allow small children to
use a hot water tap. NEVER leave a child or disabled person unattended in a bathtub
or shower.
Replace the foam dam insert and access cover after adjusting/inspecting the thermostat.
If the thermostat temperature setting (or thermostatic mixing valve) was adjusted, check
the water temperature at a faucet. Flow enough water through the faucet to ensure that
the faucet temperature reflects the mixed water temperature. Adjust the thermostat or
mixing valve setting as necessary. Adjusting the thermostat or mixing valve setting will
not immediately affect the water temperature at the faucet. Flow a sufficient amount of
water or allow a heat-up cycle to complete before making further adjustments.
Indicator Setting Temperature (°F)
• (min) 110
HOT 120
A 130
B 140
C 150
VERY HOT 160
Table 7: Thermostat Temperature Settings

Page 15
WATER PIPING
On an annual basis, all piping should be checked for leakage at joints, shut-off valves, and
unions.
T&P RELIEF VALVE
On an annual basis, the temperature and pressure relief valve should be checked for proper
operation. First, attach a drain line to the valve to direct the water discharge to an open
drain. This is very important because the temperature of the discharge could be very hot.
Second, lift the lever at the end of the valve several times. The valve should operate freely
and return to its original position properly. If water does not flow out of the valve, remove
and inspect for corrosion or obstructions. Replace with a new valve if necessary. Do not
repair the faulty valve as this may cause improper operation.
ANODE RODS
Anode rods should be inspected twice in the first year and at least yearly once a time interval
for inspection has been developed. It is recommended to check the rod(s) six months after
the heater is installed. If the anode rod had reduced in size by two-thirds of its original
diameter of 3/4” or shows signs of pitting, it is time for replacement. Take the following
steps when changing the anode rod(s):
1. Shut off water supply.
2. Open any faucet to relieve tank pressure.
3. Remove caps on water heater top; push insulation aside.
4. Use a 1 1/16” six-sided socket wrench and a breaker bar. Snap hard to break the anode
rod seal.
5. Remove rod(s) and replace with new rod(s).
6. Turn water supply back on and leave faucet open until air is out of line.
7. Turn faucet off and check that new rod(s) doesn’t leak.
8. Snap caps back into place.
FLUSH THE TANK
The Sun Bandit®Hybrid Water Heater is glass lined. Elements in the water such as lime,
iron and other minerals may accumulate in the heater. It is recommended that the tank be
drained and flushed thoroughly once a year to prevent buildup in the tank.
MIXING VALVE
The thermostatic mixing valve should be checked annually to ensure proper operation. Refer
to the installation instructions for the manufacturer’s recommended maintenance procedure.
SECTION VI: MAINTENANCE

Page 16
SECTION VII: TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
No hot water at faucet ECO on thermostat tripped Determine cause of ECO trip (faulty temperature
regulation at thermostat?). Adjust or replace as
necessary. Reset high limit (depress red button).
Improper thermostat setting Turn thermostat to safe temperature setting
Electrical problem (relay, wiring, etc.) Check fuse and replace
Check circuit breaker and reset (if applicable)
Check power supply
Water at faucet too hot Thermostat set too high Lower thermostat setting to safe level
Thermostatic mixing valve not properly
adjusted
Check manufacturer’s instructions
Insufcient hot water Thermostat set too low Raise thermostat setting to safe level. See Section V
Peak use of hot water is greater than tank
storage capacity
Determine peak usage, compare to tank capacity, and
add additional storage (storage tank) if necessary
Faulty tank thermostat Replace thermostat
Scale, hard white particles from
faucets, popping sound from tank
Lime, water hardness above 7 grains-120ppm Remove and clean the heating elements. Add a
water treatment system (water softener, etc.)
Rust staining; bad taste and odor
in water
Iron/minerals in water supply Filtration
Rotten egg odor Hydrogen Sulde Flush tank with chlorine solution and install alumi-
num anode rod(s)
Air from hot water xture Electrolysis or air introduced by water supply Properly ground heater & replace anode rod(s).
Check well pump system.
Reduction in recovery Dip tube broken or scale build up on heating
elements.
Replace dip tube or clean/replace heating ele-
ments.
Inlet/Outlet tting corrosion Galvanic corrosion of dissimilar metals Install dielectric unions
T&P Valve dripping water Excessive water pressure (above 150 psi) Check incoming water supply pressure; closed loop
system requires expansion tank
T&P gushing water Excessive water temp. (above 210°F) Adjust or replace thermostat and T&P valve

Page 17
SECTION VIII: PARTS LIST




















 

 
   









®
®
Part Description
1Hot Outlet with Anode 11 Thermostat Mounting Bracket
2Dip Tube 12 Heating Element Gasket
3Anode Rode 13 AC Micro-Grid Resistive Element
4J-Box Cover 14 Thermostat Cover (long)
5J-Box Cover (w/ conduit hole) 15 Foam Dam Cover
6Sensor Immersion Well 16 Access Cover
7T&P Relief Valve 17 Standard Utility Powered Resistive Element
8Upper AC Micro-Grid Thermostat 18 Thermostat Cover (short)
9Standard Utility Power Thermostat 19 Plug (1" NPT)
10 Lower AC Micro-Grid Thermostat 20 Drain Valve
21 Thermometer
Table 8: 30, 50, 80 Gallon Parts List (Model designations containing “100200”)

Page 18
SECTION VIII: PARTS LIST (cont.)










 







 
   















®
®
Part Description
1Hot Outlet with Anode 10 Heating Element Gasket
2Dip Tube 11 AC Micro-Grid Resistive Element
3Anode Rode 12 Thermostat Cover (long)
4J-Box Cover 13 Foam Dam Cover
5J-Box Cover (w/ conduit hole) 14 Access Cover
6Sensor Immersion Well 15 Standard Utility Powered Resistive Element
7T&P Relief Valve 16 Plug (1" NPT)
8AC Micro-Grid or Standard Utility
Power Thermostat 17 Drain Valve
9Thermostat Mounting Bracket 18 Thermometer
Table 9: 30, 50, 80 Gallon Parts List (Model designations containing “300400”)