Sunbeam Cafe Latte EM5400B User manual

Please read these instructions carefully
and retain for future reference.
Café Latte
Pump espresso machine
Instruction Booklet
EM5400B

Contents
Important instructions – retain for
future use.
Sunbeam’s Safety Precautions 2
About espresso coffee 3
Features of your Café Latte 4
Operations Guide for your Café Latte 7
Secrets to the perfect cup 11
Easy steps for texturing milk 12
Before using your Café Latte 13
Functions of your Café Latte 14
Care and Cleaning 17
Descaling 19
Trouble Shooting Guide 21
Recipes 24

2
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Sunbeam’s Safety Precautions
Sunbeam are very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• Close supervision is necessary when your
appliance is being used near children or
infirm persons.
• Young children should be supervised to ensure
that they do not play with the appliance.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
SAFETY PRECAUTIONS FOR YOUR SUNBEAM
ESPRESSO MACHINE.
• Always place the unit on a flat, level surface.
• Do not operate without water in reservoir.
• Do not remove the filter holder during water
flow or coffee flow as the unit is under
pressure. Removing the filter holder during
operation can lead to a scalding or injury.
• Clean the steam nozzle only when the unit has
been switched off and allowed to cool.
• Disconnect the plug from the power outlet if
there is any problem during the coffee making
process or prior to cleaning your appliance.
• Do not allow the power cord to come into
contact with the hot parts of the appliance
(cup warming plate, filter holder, steam
nozzle).
• Keep hands away from hot parts of the
appliance, including the cup warming plate,
filter holder and steam nozzle.

3
About espresso coffee
The Sunbeam Café Latte is the ultimate
espresso machine for people who really
appreciate fine coffee. With its robust
metal design, powerful 15 BAR pump and
‘Thermoblock’ heating system, the Sunbeam
Café Latte will provide many enjoyable cups
of quality coffee.
Coffee is an integral part of Australian
culture. With Café numbers increasing, the
demand for the perfect cup combined with
the right atmosphere is the goal of many
coffee connoisseurs.
What makes a good coffee?
Sunbeam have consulted with experienced
coffee makers and appreciators of coffee
through every stage of design, to ensure the
machine delivers a great coffee every time.
There are many factors that contribute to the
perfect coffee. The words’ ‘taste’ and ‘aroma’
are consistently used when describing the
perfect cup.
The sweet aroma and taste of the perfect
coffee is largely due to the correct
combination of temperature and pressure
during the brewing process. The ‘Thermoblock’
heating system ensures the water is at the
correct temperature, so that the full coffee
flavour is extracted.
Secondly, the combination of the 15 BAR
pump, dual-wall filter and stabilising baffle
ensures the correct pressure at which the
liquid espresso is released from the spout.
The flow should consist of both liquid and
cream. This cream is commonly known as the
Crema. The perfect Crema should be thick and
stable and preserve the coffee flavour, aroma
and temperature.
We hope you have many enjoyable coffee
experiences with the Sunbeam Café Latte.
Should you need any further assistance,
please don’t hesitate to contact the Sunbeam
coffee hotline on free call 1800 025 059.

4
Features of your Sunbeam
Café Latte
Warming plate
Allows up to 9 espresso cups to be warmed
before use.
Warm Up light
Power light
On/Off switch
Brewing head
Brass & Phenolic Filter handle
Full metal structure and components
Die-cast metal and stainless steel quality
components, built to last.
Water level indicator
The water level indicator floats through the drip
tray indicating how full the drip tray is. The
top of the indicator has a red band for easy
identification.
Non-slip rubber feet
Makes the unit sturdy, preventing it from slipping
or scratching the bench top.
Tamp
Measuring spoon

5
2.1L removable water reservoir
The large water reservoir is removable for easy
filling. Simply lift and remove in any direction.
Operating dial
Easy to operate selector dial - turn to the right
to make Espresso ( ) or to the left for Steam
( ).
Steam arm
Froth enhancing steam attachment
Designed for ease of use, the rubber froth
attachment creates thick, dense and shiny
milk froth in seconds.
Extra cup height clearance
Additional clearance between the coffee
handle and the drip tray – designed to suit
taller cups.
Removable drip tray
Designed with no dirt traps for small coffee
granules, milk or any other spills. You can
simply wipe clean all surfaces. The drip tray
can be completely removed for easy cleaning.
Stainless steel frothing jug
1 cup filter 2 cup filter

15 BAR pump – Italian designed & manufactured
Supplies the correct and essential pressure necessary for full extraction of oils from
the coffee grinds.
Thermoblock heating system
Ensures the precise temperature is achieved. As espresso is made with hot rather than
boiling water the thermoblock heats the water to 92°C (just below boiling point) for optimum
extraction of oils from the coffee grinds. Temperatures above this will burn the coffee grinds.
Crema system – Italian designed
The dual-wall filter creates additional
back pressure and the stabilising
baffle produces a steady pour and
maintains the temperature of the
espresso.
6
Features of your Sunbeam
Café Latte

7
Operations Guide for your
Café Latte
The diagrams below and on the following pages are to assist you in using your Sunbeam Café
Latte. Each of the diagrams is numbered. Throughout this instruction manual these numbers
will be referred to.
For example: Fill the water reservoir (1) (2) (3) (4) (5) with cold tap water...
Each time you see these numbers please refer back to the diagrams at the front of the
instruction manual.
Filling the water reservoir.
1 2 3
Open lid of water reservoir. Fill in place with cold water,
OR
Remove water reservoir.
7 8 9
2 cup
filter
1 cup
filter
Select Filter. Place filter handle onto
brewing head.
Turn filter handle to the
right as far as it will go.
Preparing the espresso machine.
4 5 6
Fill at sink with cold water. Replace the water reservoir. Turn on the unit.

8
Operations Guide for your Café Latte (continued)
10
13
16
11
14
17
12
15
Place filter handle onto
brewing head and turn
handle to the right, as far
as it will go.
Turn the operating dial
to the right to make an
espresso.
Place coffee in filter. Tamp the coffee.
Wipe the edge of filter to
remove any coffee grinds.
Place container under
brewing head.
Turn operating dial
to the right.
Warming espresso cups.
Making an Espresso.

9
Operations Guide for your Café Latte (continued)
18
21
19
22
20
Remove used coffee grinds. Attach the froth enhancing
steam attachment to the
steam arm.
Turn the operating dial to
the left to texture milk.
Remove the frothing
attachment.
Turn the operating dial to
the left to heat water.
Hot water drinks.
Frothing Milk.
Remove the water reservoir
from the espresso machine.
23
Remove the BLACK steam
nozzle cleaning wire from the
base of the espresso machine,
where the water reservoir sits.
24
Insert cleaning wire into
the hole in the base of the
steam arm/wand.
25 26
Remove steam nozzle from
steam arm.
Care and Cleaning.

10
Operations Guide for your Café Latte (continued)
27
Remove the GREY cleaning
wire from the base of the
espresso machine where
the water reservoir sits.
Insert the cleaning wire into
the single hole in the base
of the filter.
28 29
30 31
Ensure plastic lining is
clipped back into position
in the drip tray.
To remove drip tray, pull tray
outward and toward you.
Remove the drip tray grid.

11
With a Sunbeam pump espresso machine
and a little experience, you can create
café-quality coffee at home. Here are a few
helpful suggestions:
• The origin of the bean and roasting will
affect the taste of the espresso, so test
different brands and blends of coffee to
find the one you like best.
• The grind of the coffee is critical. Vary the
degree of grinding to find the right fineness
for the coffee beans being used.
• A regular shot of espresso, the base of all
cafe coffees is approximately 30mls. The
shot of espresso is a concentrate, vary the
quantity of milk and additional hot water to
determine the strength and volume of the
coffee. If you are using a large cup or mug
you may require a double shot of espresso,
rather than just a single shot depending on
your taste.
• Ensure your coffee grinds are ‘tamped’
evenly. ‘Tamping’ refers to the amount
of pressure with which coffee grinds are
packed into the filter.
• If your espresso pours too slowly, tamp the
coffee grind more lightly, or try a coarser
grind.
• If your espresso is thin and watery, tamp
the coffee grinds harder, or try a finer
grind.
• Always use cold milk and a clean stainless
steel jug when steaming.
• Don’t boil the milk when steaming. The
ideal temperature is when the jug becomes
too hot to touch.
• Always use the freshest beans or ground
coffee available and store in an airtight
container in a cool, dry, dark place.
• Whole coffee beans stay fresh longer than
pre-ground coffee.
• When grinding your own coffee, never grind
more than you will use for immediate use.
Once ground, the coffee will begin to loose
it’s goodness.
• Pre-warm cups prior to making an
espresso, either by filling with hot water or
placing on the warming plate.
• Always use cold milk and a clean stainless
jug when texturing milk.
• Do not boil the milk when texturing. The
ideal temperature is when the jug becomes
too hot to touch.
• Once prepared, serve coffee immediately.
• Keep your espresso machine clean and
thoroughly rinsed. Run water through
the brewing head and flush the steaming
nozzle in fresh water after each use.
Secrets to the perfect cup

12
Milk texturing is the steaming of milk to heat
it and to create froth. Similar to making an
espresso, perfecting the art of milk texturing
takes time and practice.
• Use fresh, cold milk and fill a stainless
steel frothing jug to no more than ¹/³ full.
• The amount of milk you steam should be
adequate for the coffees you are preparing.
Keep in mind that the volume of milk will
increase or ‘stretch’ during the texturing
process.
• Once you have activated the steam and
inserted the steam nozzle into the jug,
position the steam arm 1½ cm from the
side of the jug with the tip of the nozzle
just below the surface of the milk. The
jug needs to be at a slight angle with the
steam arm resting on the spout of the jug.
This will create a whirlwind motion in the
milk.
Note: You should hear a hissing sound. If you
are creating large bubbles, raise the jug so
that the nozzle tip is lowered deeper into the
milk.
• As the steam heats the milk, the milk will
begin to rise. Follow the level of the milk
by lowering the jug, always keeping the tip
of the steam nozzle just below the surface.
• Once the milk has stretched to double its
original volume, lower the steam nozzle
further into the milk and continue to heat
the milk. This will give the milk a fine
texture and not a mass of large aerated
bubbles.
• Cease steaming when the frothing jug
becomes too hot to hold your hand against
it.
• With the frothing jug in hand, swirl and tap
the jug until the milk becomes shiny and
no bubbles remain, this ensures an even
consistency. Pour the textured milk into
your espresso as soon as possible.
Frothing with the frothing attachment
If you are just learning to texture/froth milk
you may find it initially easier using the
frothing attachment packed with the Café
Latte. Once you have had some practice in
texturing/frothing milk, we recommend not to
use the frothing attachment as you will have
greater control of the texture and temperature
of the milk.
• Attach the frothing attachment to the
steam arm (19).
• Once you have activated the steam,
insert the steam arm with the frothing
attachment into the jug. Position the
steam arm 1½ cm from the side of the jug
with the frothing attachment completely
immersed in the milk, so the tip of the
frothing attachment is held just above the
base of the jug.
• Hold the frothing attachment in this
position until the milk has stretched to
double its original volume. Cease steaming
when the frothing jug becomes too hot to
hold your hand against it.
Important cleaning instructions for the steam
wand/arm
The steam arm/wand and froth enhancing
attachment needs to be cleaned each time
you froth milk. To clean the steam arm/wand,
wipe with a damp cloth and rinse the froth
enhancing attachment under warm water.
Should your steam arm/wand become
blocked, supplied with your espresso machine
is a cleaning wire. The cleaning wire for the
steam arm is the BLACK pin, located under
the base of the water reservoir (23) (24).
With the cleaning wire insert it into the hole
in the base of the steam arm/wand (25).
If the steam arm/wand remains blocked,
using the measuring spoon/tamp unscrew the
steam nozzle from the steam arm (26).
Clean the steam nozzle by once again using
the cleaning wire and then flush under
running water.
Easy steps for texturing milk

13
Before using your Sunbeam Café Latte for the
first time or if you have not used it for some
time, rinse the machine by running water
through without coffee in the filter holder, as
follows:
Note: Throughout these instructions the
numbers you see highlighted and in brackets
refer back to the diagrams at the start of this
instruction manual.
• Open the lid of the water reservoir (1) and
fill with cold water (2). Alternatively you
can open the lid and remove the water
reservoir using the handle (3). Then fill
with cold water (4).
• Replace the water reservoir firmly into the
unit (5) and close lid.
• Insert the power cord into a 230-240V AC
power outlet and turn the power on. Start
the unit (6). The red ‘Power’ light and
‘Warm Up’ light will both illuminate.
• Place one of the filters in the filter handle
(7). Then position the filter handle on the
machines brewing head.
• To ensure that the filter handle is in
the correct position, turn the handle so
it points to the left and place the filter
handle flat against the brewing head (8),
then turn the handle towards the right (9),
as far as it can go.
Note: Do not over tighten.
• Place a sufficiently large container under
the brewing head (10).
• As soon as the orange ‘Warm Up’ light
goes off, turn the operating dial to the
setting (11) and allow all the water in the
water reservoir to run through.
• If necessary, you may need to stop the
operation by turning the operating dial to
the ’Off’ position, empty the container,
then resume the operation.
Note: Make sure that the water reservoir
is clean and free of any debri, as any fine
particules can block the water flow.
Before using your Café Latte

14
1. ESPRESSO FUNCTION
For best results, it is ideal to pre-heat your
cups, filter handle and filter as follows:
• Insert the power cord into a 230-240V AC
power outlet and turn the power on.
• Fill the water reservoir (1) (2), (3) (4) (5)
with cold water and start the appliance (6).
• Put the filter handle and an empty filter
in place (7) (8) (9), and place cups
underneath the filter handle.
• When the machine is ready, the orange
‘Warm Up’ light goes off, turn the
operating dial to setting (11).
• When the cups are full of hot water,
return the operating dial to the ’off’
position.
Note: Once the appliance has been on for
a while, the coffee cups can be warmed
by placing them upside down on the cup
warming plate (12).
Preparing an espresso:
• Insert the power cord into a 230-240V AC
power outlet and turn the power on.
• Fill the water reservoir (1) (2), (3) (4) (5)
with cold water.
• Start the unit (6). The red ‘Power’ light
and orange ‘Warm Up’ light will both
illuminate.
• Pre-heat your coffee cups by placing them
upside down on the cup warming plate (12).
• Select the required filter (7) for 1 or 2
cups of coffee and place in the filter
handle.
• Using the measuring spoon supplied, place
one or two measures of ground coffee into
the filter (13). With the other end of the
measuring spoon, use the tamper to push
(pack) down the coffee grinds (14).
Important: Be sure not to over-fill the filter
with too much coffee, and wipe around the
edge of the filter to remove any coffee grinds
(15).
• Place the filter handle on the machines
brewing head. Position the handle so it
points to the left, place the filter handle
flat against the brewing head, then turn
the handle towards the right (16) as far as
it can go.
Note: Do not over tighten.
• Place 1 or 2 pre-heated cups below the
pouring spouts.
• When the Sunbeam Café Latte is at the
correct temperature the orange ‘Warm Up’
light will go out, then turn the operating
dial to the setting (17). You will hear
the machine making a pumping noise, this
is normal.
• Once the cup/s are filled to the desired
level, turn the operating dial to the ‘off’
position.
• Remove the filter handle and the filter by
turning the filter handle to the left.
• To remove the used coffee grinds from the
filter, simply turn the filter handle upside
down in a bin and gently tap out the
coffee (18).
Functions of your Café Latte

15
• After each use of the espresso machine
for best results when making consecutive
cups of espresso we recommend that you
flush a small amount of water through
the machine with the filter handle already
removed from the brewing head. Simply
turn the operating dial to the setting
and allow the water to run through until
you have a consistent flow of water. This
will wash out any old or used coffee grinds
stuck to the underside of the brewing head
and also help ensure the correct water
temperature for your next shot of espresso.
• Once the orange ‘Warm Up’ light goes out
your machine is ready to make the next
espresso.
Note: Do not leave the filter handle locked
in position for extended periods, or when
machine is not in use. This shortens the
life of the brew head rubber seal.
2. STEAM FUNCTION
The steam function can be used for texturing/
frothing milk or heating liquids.
Important: There is a risk of scalding when
the steam nozzle is in use. Hot water or
hot steam can cause scalding. Only use the
steam wand/arm when it is immersed in the
milk.
• Fill the water reservoir (1) (2) (3) (4) (5)
with cold water.
• Start the unit (6). The red ‘Power’ light
and orange ‘Warm Up’ light will both
illuminate.
• Swing the steam nozzle to the side of the
machine.
• Pour cold milk into a stainless steel jug to
no more than
1/3
full.
Tip: For best results we recommend using
refrigerated milk and a stainless steel jug
that is well chilled. Be sure not to rinse the
jug with warm water before use.
• When the Sunbeam Café Latte is the right
temperature the orange ‘Warm Up’ light
will go out.
• Hold the jug under the steam wand/arm
so that the nozzle opening is completely
immersed in the milk. Turn the operating
dial to the setting to activate the steam
and commence texturing the milk (20).
Tip: For instructions on how to froth/
texture milk refer to section 'Easy steps for
texturing milk'.
• Lower the jug so that the tip of the steam
nozzle is just below the surface of the milk
and place your hand on the side of the jug.
Note: The nozzle must not touch the
bottom of the jug to ensure that the steam
release is not obstructed.
• Move the jug so that the steam wand/arm
is to one side, this will create a whirlwind
motion to the milk. As the steam heats the
milk, the milk will begin to rise. Follow
the level of the milk by lowering the jug,
always keeping the tip of the steam nozzle
just below the surface.
• Cease steaming when the jug becomes too
hot to continue holding the palm of your
hand against the side. Simply turn the
operating dial to the ’off’ position and
remove the jug.
Note: Do not boil the milk.
Functions of your Café Latte (continued)

16
Cleaning the steam wand/arm and froth
attachment
You must clean the steam wand/arm and
froth attachment immediately after each use.
Simply wipe the stainless steel steam wand/
arm clean with a damp cloth and place the
froth attachment under warm running water
to remove any excess milk. Also, briefly turn
the operating dial to setting to clear any
remaining milk out of the steam wand/arm.
Caution: Steam from the wand/arm is
extremely hot and there is danger of scalding.
Note: Should your steam wand/arm become
blocked, supplied with your espresso
machine is a cleaning wire. The cleaning wire
for the steam arm is the BLACK pin, located
under the base of the water reservoir (23)
(24). With the cleaning wire insert it into the
hole in the base of the steam wand/arm (25).
Should the steam wand/arm remain blocked,
using the measuring spoon/tamp unscrew the
steam nozzle from the steam arm (26) clean
the steam nozzle by once again using the
cleaning wire and flush under running water.
Hot water drinks
You are able to heat water for hot drinks
such as tea or instant soups using the steam
nozzle.
Note: Heating liquids is done with the
steam nozzle only, so ensure that the froth
attachment is not in place.
• Fill the water reservoir (1) (2) (3) (4) (5)
with cold water.
• Start the unit (6). The red ‘Power’ light
and orange ‘Warm Up’ light will both
illuminate.
• Remove the froth attachment from the
steam nozzle (21) and swing the steam
nozzle to the side of the machine.
• When the Sunbeam Café Latte is the right
temperature the orange ‘Warm Up’ light
will go out.
• Immerse the steam nozzle in the cup or
container holding the liquid to be heated
and turn the operating dial to the
setting (22).
• When the liquid is hot enough, turn the
operating dial to ’off’ position and
remove the container or cup.
Note: It is normal for the orange ‘Warm Up’
light to turn on and off during
heating of water.
Functions of your Café Latte (continued)

17
The coffee making process involves extracting
oils out of coffee grinds to make espresso
coffee. Deposits of these oils build up over time
and affect the taste of the coffee and operation
of the espresso machine.
Regular cleaning to remove these oils is
essential for espresso machines to keep
operating effectively. Flushing water, through
the brewing head and the steam wand/arm, is
the easiest way to keep your machine clean
after making each coffee, and at the end of
your coffee making session.
Important: Never wash your espresso machine
accessories in the dishwasher.
Drip tray
Remove the grid and drip tray at regular
intervals to empty (29), (30). If the red floating
level indicator appears through the grid, empty
the drip tray immediately.
Clean the drip tray and its grid with water and a
little non-abrasive washing up liquid, rinse and
dry.
Over time it is normal for the inside of the drip
tray to be stained by the oils in the coffee.
Note: Ensure that when you are replacing the
d rip tray that the plastic lining is in position (31).
The brewing head, filters & filter handle
The filter and filter handle should be washed
after each use by rinsing them under warm
water. Wash at regular intervals in warm soapy
water using a mild detergent.
To clean the brewing head, flush water through
and wipe the head and around the inside rim
with a damp cloth.
To assist in keeping the filter and the brew
head clean, at the end of each coffee making
session we recommend you run the machine,
with the filter in place, without coffee – using
water only.
Should the holes in the filters become clogged
with coffee granules use a fine bristled brush to
remove them.
Important: Should the filter remain blocked
after normal cleaning, supplied with your
espresso machine is a cleaning wire. The
cleaning wire for the filter is the GREY pin
located under the base of the water reservoir
(23), (27) with the cleaning wire insert it into
the single hole in the base of the filter (28).
Care and Cleaning

18
Care and Cleaning (continued)
Brew head rubber seal
This seal is located in the brewing head and
creates a seal against the filter handle when
making an espresso.
Note: When your Sunbeam Café Latte is not
being used, we recommend that you do not
leave the filter handle attached to the machine
as this will reduce the life of the seal.
Over time this seal looses its elasticity and
will require replacement – usually every 6-12
months. Signs that the seal is deteriorating are
when: the filter handle rotates to the far right
and feels loose, or steam escapes from around
the brewing head during use.
The cup warming plate and exterior
Wipe over the unit with a damp cloth and wipe
dry. Do not use abrasives or metal scourers, as
these will scratch the exterior surface.
Steam wand/arm and froth attachment
The steam wand/arm and froth attachment
needs to be cleaned each time you texture
milk or heat any other liquid. To clean the
steam wand/arm, wipe with a damp cloth and
for the froth attachment, simply rinse it under
warm water.
Note: After each use we recommend that a
small amount of steam is purged from the
steam wand/arm.
On a monthly basis we recommend thoroughly
cleaning the steam wand/arm.
To do this soak the wand/arm in water with the
stainless jug resting on the drip tray. Ensure
that the water level in the jug is over the wand/
arm. Run steam through the wand/arm for 30
seconds, then leave to soak overnight.
In the morning turn the machine on and run
steam through the wand/arm again for 30
seconds.
Important: Do not wash parts in the dishwasher.
Do not immerse the unit in water.
Important: Should your steam wand/arm
become blocked, supplied with your espresso
machine is a cleaning wire.
The cleaning wire for the steam arm is the
BLACK pin located under the base of the water
reservoir (23) (24).
With the cleaning wire insert it into the hole in
the base of the steam wand/arm (25).
Should the steam wand/arm remain blocked,
using the measuring spoon/tamp unscrew the
steam nozzle from the steam arm (26). Clean
the steam nozzle by once again using cleaning
wire and then flush under running water.