_________________________________________________________________
CHARGING
Fully charge before f rst use. For max mum eff c ency,
charge after each use or every 2
s be ng stored. Fa lure to properly charge as l sted below could damage the
performance. CAUTION: ONLY USE CHARGERS PROVIDED WITH THE SOLARPOD
DAMAGE MAY OCCUR.
Charging Indicator - Indicates Charging Rate
1.
F ve yellow
LEDs represent the charg ng rate when us ng any of the methods of charg ng
LED equals approx mately 20% charge rate. Th s w ll help you to pos t on a solar
panel n the best angle to the sun. If the Solarpod™ Pro 1000
or 12V - 24VDC power source, all 5 LEDs should be llum nated.
Battery Indicator - Indicates Battery Capacity Level
1.
F ve blue LEDs represents the current battery capac ty.
2.
Each blue LED represents approx mately 20% full.
Solar Charging (recommended Sunbird Solar 120 Solar Panel)
1.
The Solarpod™ Pro 1000 has bu lt-
n battery protect on and does not requ re a solar charge
controller.
2.
Place the solar panel n d rect sun.
3.
Connect the solar charg ng cable ( ncluded) male p n t p to the DC IN port
Pro 1000. Connect the MC4 (+) and (-) t ps to the solar panel.
4.
Adjust the solar panel so that t s d rectly fac ng the sun.
Charg ng w ll beg n mmed ately
the yellow charg ng LED nd cators w ll llum nate.
5.
To ensure full battery charge, cont nue charg ng for 1 add t onal hour.
6.
To max m ze battery cycle l fe, d sconnect when Solarpod™ Pro 1000
AC all Charging (Adapter Included)
1.
Connect the male p n t p of the AC Wall Charger nto the DC IN port of the
and then plug the other end nto an electr cal outlet.
2.
The charg ng nd cator on the AC Wall Charger
w ll llum nate red when charg ng s n process
and green when the Solarpod™ Pro 1000 has reached a full charge.
3.
The yellow charg ng LED nd cators w ll also llum nate.
4.
To ensure full battery charge, cont nue charg ng for 1 add t onal hour after
There s no need to d sconnect AC Wall Charger when charg ng s complete.
Connecting Charging Lines to the Solarpod™ Pro 1000
1.
Al gn head tabs w th DC IN socket on back of un t.
2.
Turn head clockw se unt l the s lver lock tab s a
t top and press lock tab toward un t.
3.
To unplug charg ng head, follow the above steps n reverse order.
_________________________________________________________________
charge after each use or every 2
LEDs represent the charg ng rate when us ng any of the methods of charg ng
LED equals approx mately 20% charge rate. Th s w ll help you to pos t on a solar
n battery protect on and does not requ re a solar charge
Charg ng w ll beg n mmed ately
w ll llum nate red when charg ng s n process
To ensure full battery charge, cont nue charg ng for 1 add t onal hour after
There s no need to d sconnect AC Wall Charger when charg ng s complete.
t top and press lock tab toward un t.
________________________________________________________________________
OPERATING INSTRUCTIONS
Once charged, the Solarpod™ Pro 1000
s ready to use r ght out of the box. No set up s requ red.
All outputs may be used s multaneously. Check your dev ce’s spec f cat ons to make sure they are
compat ble w th the Solarpod™ Pro 1000.
ON/OFF Button - When on, the sw tches
AC Power Button - When on, the sw tches
USB Operation
• Turn the ON/OFF BUTTON on.
•
Plug n your dev ce’s USB power or charg ng
A comb ned 5V/2A max mum output s ava lable between the two ports (when fully
D sconnect and power off when not n use
AC Operation (max 1000W output)
• Press the AC power button
Plug n your dev ce’s power or charg ng cable nto the electr cal
• D sconnect and turn off the
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
THE VOLTAGE RATING OF THE
: Us ng dev ces rated h gher than
m nutes may cause the Solarpod™ Pro
cooled the c rcu t w ll reset and the
Advantages of a Pure Sine Wave Inverter
•
A pure s ne wave nverter produces a nearly perfect s ne wave output (less than 3%
total harmon c d stort on) that s essent ally
nterference, overheat ng and no se.
Computer crashes and other appl ance operat onal gl tches can be avo ded.
•Induct ve loads such as var able-
speed motors and m crowave ovens can be used,
and supports n runn ng them qu eter and cooler.
and sens t ve electron cs w ll s mply not work properly w thout
Reduces aud ble and electr cal no se n fans, fluorescent l ghts, magnet c c rcu t
breakers and electron c gears.
12V DC Operation ( ax 15A output)
• Turn the ON/OFF BUTTON on.
•
Plug n your 12V dev ce’s power or charg ng cable nto the 12V Veh cle Socket
• Ne ther power button need to be on.
•
D sconnect and power off when not n use
________________________________________________________________________
s ready to use r ght out of the box. No set up s requ red.
All outputs may be used s multaneously. Check your dev ce’s spec f cat ons to make sure they are
Plug n your dev ce’s USB power or charg ng
A comb ned 5V/2A max mum output s ava lable between the two ports (when fully
D sconnect and power off when not n use
Plug n your dev ce’s power or charg ng cable nto the electr cal
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
1000 UNIT YOU HAVE PURCHASED.
: Us ng dev ces rated h gher than
900-1000W and operated for more than 10
to overheat and shut down. Once t has
1000 w ll be operat onal aga n.
A pure s ne wave nverter produces a nearly perfect s ne wave output (less than 3%
total harmon c d stort on) that s essent ally
dent cal to ut l ty-suppl ed gr d power.
nterference, overheat ng and no se.
Computer crashes and other appl ance operat onal gl tches can be avo ded.
speed motors and m crowave ovens can be used,
and supports n runn ng them qu eter and cooler.
and sens t ve electron cs w ll s mply not work properly w thout
Reduces aud ble and electr cal no se n fans, fluorescent l ghts, magnet c c rcu t
Plug n your 12V dev ce’s power or charg ng cable nto the 12V Veh cle Socket
D sconnect and power off when not n use
