sunjoe HJ22HTE User manual

© 2019 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
A Division of Snow Joe®, LLC Model HJ22HTE Form No. SJ-HJ22HTE-880E-MR6
R
OPERATOR’S MANUAL
ELECTRIC HEDGE TRIMMER
22-INCH | 3.5 AMP
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Power Tool Safety
Warnings
m WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not followed, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not followed, could result in minor or moderate injury.
Work Area Safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
3. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the inuence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
2. Use safety equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in
the o-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught in
moving parts.

2
7. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Power Tool Use + Care
1. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not turn it
on and o. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the powertool accidentally.
4. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may aect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
7. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations dierent from those intended could result in a
hazardous situation.
Service
Have your power tool serviced by a qualied repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
Hedge Trimmer Safety Warnings
1. Keep all parts of the body away from the cutter blade. Do
not remove cut material or hold material to be cut when
blades are moving. Make sure the switch is o when
clearing jammed material. A moment of inattention while
operating the hedge trimmer may result in serious personal
injury.
2. Carry the hedge trimmer by the handle with the cutter
blade stopped. Blades coast after turn o. Proper
handling of the hedge trimmer will reduce possible personal
injury from the cutter blades.
mDANGER! Keep hands away from blade. Contact with
blade will result in serious personal injury.
3. Use both hands when operating the hedge trimmer.
Using one hand could cause loss of control and result in
serious personal injury.
4. Hold the power tool by insulated gripping surfaces
only, because the cutter blade may contact hidden
wiring or its own cord. Cutter blades contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
5. Keep cable away from cutting area. During operation
the cable may be hidden in shrubs and can be
accidentally cut by the blade.
6. Inspect the area to be cut and remove any foreign
objects that will inuence your cutting. If the foreign
objects can not be removed, e.g. wire fences, please mark
and remember it to avoid toughing them during cutting.
7. Hold the hedge trimmer properly with both hands.
Additional Safety Rules for
Hedge Trimmer
1. Recommendation for the use of a residual current device
with a tripping current of 30 mA or less
2. Instructions for proper assembly of the handle and/or
guard if the hedge trimmer is shipped without the handle
or guard in place. In addition, the following warning
statement shall be included in the instructions:
mWARNING! Only use with handle and guard properly
assembled to hedge trimmer. The use of the hedge
trimmer without the proper guard or handle provided may
result in serious personal injury.
3. If devices or facilities are available for the extraction and
collection of dust, ensure these are connected or properly
used. Use of these devices can reduce dust related
hazards.
4. Remove any blade that has been damaged. Always make
sure that the blade is installed correctly and securely
fastened before each use. Failure to do so can cause
serious injury.
5. Never cut any material over 0.63 in. (16 mm) in diameter.
6. Do not use the safety guard or clipping deector as a
gripping surface.
7. Service on the product must be performed by qualied
repair personnel only. Service or maintenance performed
by unqualied personnel could result in injury to the user
or damage to the product.
8. If the power supply cord is damaged, it must be replaced
only by the manufacturer or by an authorized service
center to avoid risk.
9. Do not use the hedge trimmer if the switch does not turn it
on and o. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
10. Use the hedge trimmer and accessories in accordance
with these instructions, taking into account the working

3
conditions the work to be performed. Use of the power
tool for operations dierent from intended use could lead
to a hazardous situation.
Electric Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
this electric hedge trimmer. Receptacles are available
having built-in GFCI protection and may be used for this
measure of safety.
2. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
Use this appliance only with a polarized UL-, CSA-, or
ETL-listed extension cord recommended for outdoor,
all-weather use.
The appliance plug will t into a polarized extension
cord only one way. If the appliance plug does not t
fully into the extension cord, reverse the plug. If the plug
still does not t, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. The extension cord plug will t into
the polarized wall outlet only one way. If the plug does
not t fully into the wall outlet, reverse the plug. If the plug
still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug,
extension cord receptacle, or extension cord plug in any
way.
3. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current product. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
4. To prevent the appliance cord from disconnecting from
the extension cord during operation, use the onboard
extension cord restraint hook and/or make a knot with the
two cords as shown in Table 1.
5. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
6. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed
or grounded.
7. If the supply cord is damaged, it must be replaced by an
electrician or a power tool repairer.
8. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD with a tripping current of
30 mA or less reduces the risk of electric shock.
10. Have your tool repaired by an electrician or a qualied
service center. This power tool complies with relevant
safety requirements. To avoid danger, electrical appliances
must only be repaired by qualied personnel using original
spare parts; otherwise this may result in considerable
damage to the user.
mWARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the hedge trimmer to make
contact with water while it is in operation. If the
appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA- or ETL-rated extension cord for
outdoor, all-weather use.
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Extension Cord
Length
Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
+50 ft - 100 ft
(+15 m - 30 m)
16 14
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord

4
Double-Insulated Appliances
In a double-insulated appliance, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a double-
insulated appliance requires extreme care and knowledge
of the system, and should be performed only by qualied
service personnel at an authorized Snow Joe®+ Sun Joe®
dealer. Replacement parts for a double-insulated appliance
must be identical to the parts they replace. A double-insulated
appliance is marked with the words “Double Insulation” or
“Double Insulated.” The symbol (square within a square)
may also be marked on the appliance.
DOUBLE-INSULATED: GROUNDING NOT
REQUIRED. WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
This hedge trimmer is double-insulated, eliminating the
need for a separate grounding system. Use only identical
replacement parts. Read the instructions before servicing
double-insulated appliances. Use this electric hedge trimmer
only as described in this manual.

5
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting to
assemble and operate.
WARNING! Do not expose the unit
to rain or wet conditions.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Wear protective gloves and non-
slip footwear when using the
machine and handling debris.
SWITCH OFF! Remove plug from
outlet before cleaning or conducting
maintenance checks.
DANGER! ROTATING BLADES –
Keep hands and feet away from
openings while the trimmer is
running.
Keep bystanders a safe
distance away from the work
area.
SWITCH OFF! Remove plug from
outlet immediately if the cord is
damaged or cut.
Double Insulation.

6
Know Your Electric Hedge Trimmer
Read the owner’s manual and safety instructions carefully before operating the electric hedge trimmer. Compare the illustration
below to the electric hedge trimmer in order to become familiar with the location of the various controls and adjustments. Save
this manual for future reference.
1. Rear handle
2. Trigger switch
3. Extension cord restraint hook
4. Power plug
5. Hand safety switch
6. Front handle
7. Safety guard
8. Cutting blade
9. Blade cover
Technical Data
Rated Voltage ................................................. 120 V ~ 60 Hz
Motor.............................................................. 3.5 A
No Load Speed .............................................. 3500 ± 10% rpm
Blade Movement ............................................ Dual-action
Blade Material ............................................... Rust-resistant,
forged-iron blades
Blade Length ................................................. 22 in. (56 cm)
Cutting Diameter Max ................................... 0.63 in. (1.6 cm)
Weight ........................................................... 5.1 lbs (2.3 kg)
6
5
4
2
37
8
9
1

7
Unpacking
Carton Contents
• Electric hedge trimmer
• Blade cover
• Manual with registration card
1. Carefully remove the electric hedge trimmer and check to
see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use the electric hedge
trimmer. The packaging is made of recyclable materials.
Properly dispose of these materials in accordance with
local regulations or save the packaging for long-term
product storage.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
Operation
Connecting to Power Supply
This product is designed with a cord restraint hook that
prevents the extension cord from disconnecting during
operation.
1. Only connect the electric hedge trimmer to a working
120 V outlet using a heavy-duty outdoor extension power
cord.
2. Make a loop in the extension cord and push it up through
the hole in the handle and around the cord restraint hook,
then connect the extension cord to the power plug (Fig. 1).
Holding the Trimmer
Before operating the hedge trimmer, stand in the operating
position and perform the following checks:
1. You are wearing all of the necessary personal protective
equipment, including protective gloves, non-slip footwear,
safety goggles, ear defenders, and close-tting clothing.
2. You are holding the unit rmly with both hands. Your right
arm is slightly bent and is holding the rear handle, and
your left arm is straight and is holding the front handle.
3. You are standing with proper footing and are holding the
hedge trimmer so that the cutting blades are always away
from your body.
mWARNING! Always keep both hands on the hedge
trimmer handles. Never hold shrubs with one hand and
operate the hedge trimmer with the other. Improper handling of
the hedge trimmer could result in serious injury.
Starting + Stopping
1. To start the tool, press and hold the hand safety switch,
then squeeze the trigger switch (Fig. 2).
2. Release the trigger switch and the hand safety switch to
stop the tool.
Cutting Procedures
mWARNING! Never cut near electric cords or power
lines. If the blade jams on any electrical cable, DO NOT
TOUCH THE BLADE. IT CAN CONDUCT ELECTRICITY
AND FATALLY SHOCK YOU! Instead, continue to hold the
hedge trimmer by the insulated rear handle, and lay it down
and away from you in a safe manner. Make sure that electrical
service to the damaged electrical cable is disconnected
before attempting to free the hedge trimmer blade. Contact
with the blade, other conductive parts of the hedge trimmer,
or live electric cords or power lines will result in death by
electrocution or serious injury.
Fig. 1
Cord restraint
hook
Extension cord
Power plug
Fig. 2
Hand safety switch
Trigger
switch

8
mWARNING! Clear the area to be cut before each use.
Remove all objects such as cords, lights, wire, or loose string
which can become entangled in the cutting blade and create a
risk of electric shock and serious personal injury.
1. When trimming new growth, use a wide sweeping action
so that the stems are fed directly into the blade. Do not try
to cut branches that are thicker than 0.63 in. (16 mm) or
those that are obviously too large to feed into the blade.
Use lopping shears, a hand saw, or a pruning saw to cut
out thick branches rst. If a substantial cut is necessary,
cut a little at a time in several passes. Cut both sides of
the hedge rst and then the top.
2. To perform a horizontal cut, hold the hedge trimmer with
the blade tilted 5-10 degrees to your cutting object; this
makes the operation easier and ensures a better cut
(Fig. 3).
3. To perform a vertical cut, start trimming at the bottom and
sweep up for even cutting. Swing the blades in an arc
towards the outsides of the hedge so that the cuttings are
swept on the ground (Fig. 4).
Care + Maintenance
mATTENTION! Before performing any cleaning or
maintenance, disconnect the unit from the power supply.
Never touch the moving blades.
mWARNING! Never spray or clean the hedge shears with
water.
1. Clean the hedge shears with a dry towel, particularly
the ventilation slits, after each use, or use a brush in the
event of heavy soiling. Spray the blades with lightweight
machine oil after each use.
2. Store the hedge trimmer in the blade cover provided.
Store the hedge trimmer in a dry location out of the reach
of children.
3. When servicing, use only identical replacement parts. Use
of any other parts can create a hazard or cause product
damage. Please contact an authorized Snow Joe®+
Sun Joe®dealer or call the Snow Joe®+ Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for all replacement parts and
accessories for your product.
Lubricate the Blades
For easier operation and longer blade life, lubricate the hedge
trimmer blade before and after each use.
1. Stop the motor and disconnect the unit from the power
supply.
2. Lay the hedge trimmer on a at surface. Apply lightweight
machine oil along the edge of the top blade (Fig. 5). If you
will be using the hedge trimmer for an extended period,
it is advisable to stop work intermittently in order to re-oil
the blade.
NOTE: Do not oil while the hedge trimmer is running.
Fig. 3
5º – 10º
Fig. 4
Fig. 5

9
Sharpening the Blades
The blade must be re-sharpened if cutting performance and
behavior begin to deteriorate (i.e. if blades frequently snag on
branches).
1. Stop the motor and disconnect the unit from the power
supply. Clamp the blade in a vise.
2. File the exposed cutting surface of each blade tooth with
a smooth round le. Be sure to retain the original angle of
the tooth when ling.
3. Remove the blade from the vise, and power on the motor
until the unsharpened edges of the remaining blade teeth
are exposed.
4. Disconnect the hedge trimmer from the power supply and
repeat the sharpening procedure as necessary.
mWARNING! Do not operate the hedge trimmer with dull
or damaged cutting blades. This may cause overload and will
give unsatisfactory cutting results.
Cleaning the Hedge Trimmer
1. Stop the motor and disconnect the unit from the power
supply.
2. Clean dirt and debris from the body of the hedge trimmer
using a damp cloth and mild detergent.
NOTE: Do not use any strong detergents on the plastic
housing or the handle. These parts can be damaged by certain
aromatic oils such as pine and lemon, and by solvents such as
kerosene.
Storage
1. Always place the blade cover on the blade before storing
or transporting the hedge trimmer. Use caution to avoid
the sharp teeth of the blade.
2. Clean the hedge trimmer thoroughly before storing.
Store the hedge trimmer indoors, in a dry place that is
inaccessible to children. Keep away from corrosive agents
such as garden chemicals and de-icing salts.
Service + Support
If your Sun Joe®electric hedge trimmer requires service or
maintenance, please call the Snow Joe®+ Sun Joe®customer
service center at 1-866-SNOWJOE (1-866-766-9563).
Model + Serial Numbers
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of your product.
These are found on the decal axed to the housing or handle
of your electric hedge trimmer. Copy these numbers into the
space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
Serial #:
H J 2 2 H T E

10
Troubleshooting
Most diculties are easy to x. Consult the troubleshooting
table for common problems and their solutions. If you continue
to experience problems or need repairs beyond these minor
adjustments, please call 1-866-SNOWJOE (1-866-766-9563)
for assistance.
Troubleshooting Table
Possible Cause
• Extension cord not connected to the
power plug
• Extension cord not connected to
power source
• Hand safety switch not fully
engaged
• Dry, corroded blades
• Blades or blade support bent
• Bent or damaged teeth
• Loose blade bolts
Problem
• Unit does not run
• Slow running, noisy, or hot blades
Possible Solution
• Check extension cord is fully
connected to tool
• Check extension cord is fully
connected to a live receptacle
• Check safety switch is fully
depressed prior to pressing trigger
switch
• Lubricate blades
• Straighten blade or blade support
• Straighten teeth
• Tighten blade bolts

11
SNOW JOE®+ SUN JOE®CUSTOMER PROMISE
PRODUCT REGISTRATION:
Snow Joe®, LLC (“Snow Joe®+ Sun Joe®”) strongly encourages
you to register your purchase. You can register online at
snowjoe.com/register, or by printing and mailing in a registration
card available online from our website, or calling our Customer
Service Department at 1-866-SNOWJOE (1-866-766-9563), or
by e-mailing us at [email protected]. Failure to register your
product purchase will not diminish your warranty rights. However,
registering your purchase will allow Snow Joe®+ Sun Joe®to
better serve you with any of your customer service needs.
WHO CAN SEEK WARRANTY COVERAGE?
This Warranty is extended by Snow Joe®+ Sun Joe®to the owner
of this Machine (a “Machine” consists of a product powered by
a motor) for residential and personal household use only. This
Warranty does not apply to products used for commercial, rental
or re-sale purposes. Should ownership of this machine change
during the 2-year period, please update the Machine’s owner
information at snowjoe.com/register.
WHAT IS COVERED?
Snow Joe®+ Sun Joe®warrants to the owner that if this Machine
fails within 2 years from the date of purchase due to a defect in
material or workmanship or as a result of normal wear and tear
from ordinary household use, Snow Joe®+ Sun Joe®will send a
replacement part or product, as needed, free of charge and with
free shipping to the original purchaser.
If, in Snow Joe®+ Sun Joe®’s sole discretion, the failed Machine
cannot be repaired with a part, Snow Joe®+ Sun Joe®will elect to
either (A) send a new Machine at no charge and with free shipping
or (B) refund the full purchase price to the owner.
WHAT IS NOT COVERED?
This Warranty does not apply to the Machines that have been used
commercially or in non-household applications. This Warranty
does not cover cosmetic changes that do not aect performance.
This Warranty is only valid if the Machine is used and maintained
in accordance with the instructions, warnings and safeguards
contained in the owner’s manual. Snow Joe®+ Sun Joe®will not
be responsible for the cost of any unauthorized warranty repairs.
This warranty does not cover any cost or expense incurred by
the purchaser in providing substitute equipment or service during
reasonable periods of malfunction or non-use of this product
while waiting for a replacement part or unit under this warranty.
Wearing parts like belts, augers, chains and tines are not covered
under this warranty, and can be purchased at snowjoe.com or
by calling 1-866-SNOWJOE (1-866-766-9563). Batteries are
covered in full for 2 years from the date of purchase.
Repair, replacement or refund of the purchase price are the
exclusive remedies of purchaser and the sole liability of Snow Joe®
+ Sun Joe®under this warranty. No employee or representative
of Snow Joe®+ Sun Joe®is authorized to make any additional
warranty or any modication to this warranty which may be
binding upon Snow Joe®+ Sun Joe®. Accordingly, purchaser
should not rely upon any additional statements made by any
employee or representative of Snow Joe®+ Sun Joe®. In no event,
whether based on contract, indemnity, warranty, tort (including
negligence), strict liability or otherwise, shall Snow Joe®+
Sun Joe®be liable for any special, indirect, incidental, or
consequential damages, including, without limitation, loss of
prot or revenue.
Some states do not allow limits on warranties. In such states, the
above limitations may not apply to you.
Outside the USA, other warranties may apply.
ABOVE ALL ELSE, Snow Joe®+ Sun Joe®are dedicated to you, our customer. We strive to make your experience as pleasant
as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We
think it’s important that you know what you can expect from us. That’s why we created the Snow Joe®+ Sun Joe®promise.
OUR PROMISE: Snow Joe®+ Sun Joe®warrant new products for two years from the date of purchase. If your product does
not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending
you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting,
sawing, mowing, washing and…?

sunjoe.com