SUNLUNE JASMINER X4 User manual

JASMINER X4
High-throughput Quiet Server
Instruction Manual
Tip: Follow the official account of SUNLUNE , then reply “course” to get the use
demonstration video of the device.
SUNLUNE Technology (Nantong) Co., Ltd.
April 2022

JASMINER X4 High-throughput Quiet Server Instruction
Manual
2
Catalogue
I Product introduction....................................................................................... 3
II Product features.............................................................................................. 3
III Inspection before use....................................................................................3
IV Description.................................................................................................... 5
V Settings........................................................................................................... 7

JASMINER X4 High-throughput Quiet Server Instruction
Manual
3
JASMINER X4 High-throughput quiet Server Instruction Manual
I Product Introduction
Jasminer X4 high-throughput quiet server, is a super cost-effective
computing server developed by Sunlune technology (Nantong) Co., Ltd.
Jasminer X4 based on memory computing integrated high-throughput ASIC. The
ASIC with memory computing integrated structure realizes the combination of
Memory and computing, increases the access bandwidth while meeting the
demand of storage capacity, breaks through the bottleneck of computing power,
save energy and size ，providing sufficient computing power, exquisite low
noice design ，solid and quite. with the integrated memory and computing
architecture and high- throughput technology, Jasminer X4 suitable for PoW
algorithms such as ETCHASH and ETHASH, satisfy various customers and bring
them a good return on investment.
Excellent performance and easy to use， Exquisite design, user friendly
interface and simple operation. Just need set a few parameters.Simple
interface,power supply and network access is required. Excellent computing
performance, efficient and concise IO expansion capability and high stability.
Energy saving, environment friendly and widely used
Very low power consumption, low-noice design, high efficiency,

JASMINER X4 High-throughput Quiet Server Instruction
Manual
4
environment friendly. Environmental temperature≤40 °C. Designed for multi-level
users, it can be used in both domestic environments and professional premises (IDC
rooms) and can be operated without specialist knowledge.
JASMINER X4 High-throughput quiet server
II Inspection before use
1.Inspection before use
After unpacking, please check for any package deformation or interface
damage. If there is any fault, please contact the after-sales department.
Check for abnormal sound, metal collision or screw loosen.If there is any
fault, please contact the after-sales department.
2.Attention
The device should be connected to router or Exchanger without Poe
function, only wired network connection can be used.
To avoid heat dissipation, do not stack or cover the device with other
objects.
Please run the device under the recommended operating environment
(operating temperature: 0-40℃, operating humidity: 5 RH~95 RH, non
condensation) to avoid affecting the normal operation or performance of
the device.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
5
Pay attention to dust and foreign matters,otherwise, the mainboard may
be corroded and the device cannot work properly.
Private renovation is not guaranteed.
III Basic description
1. Device
Front
Back
Attention:
Place the device as shown in the figure above. Do not place the device in a
closed space.
For your safety, do not remove any screws or fasteners from the device.
The device will generate heat during operation. Please avoid touching the shell
during operation.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
6
2.parameter
Overview
Specification
Type
JASMINER X4
Name
High-throughput quiet
server
Encryption algorithm
ETCHASH&ETHASH
Hashrate（MH/s）
1040±10%
INPUT
200-240V~,50/60Hz,2.4A
power consumption（Watt）
480±10
Energy efficiency ratio (25 ° C
ambient temperature, J / MH)
0.46±10%
Hardware Configuration
Network connection
RJ45 Ethernet 10/100/1000M
Device size (mm)
483×360×134
Package size (mm)
-
Device weight（kg）
10
Overall weight (including package,
kg)
-

JASMINER X4 High-throughput Quiet Server Instruction
Manual
7
3.Interface and description
TF card
TF Card slot
IP Report
When using IP report software, the high-throughput 1U
server IP address will be feedback to your PC
ETH
network interface
Reset
Restore factory setting
larm lamp
(red)
Continuous light indicates device failure
Operation lamp
(green)
Flashing light indicates device running well
IV Use and settings
1. Connection inspection
IP Report
Reset
AC IN
Network
interface
TF Card slot
Alarm lamp
Alarm lamp（red）

JASMINER X4 High-throughput Quiet Server Instruction
Manual
8
a) Network cable connection: Insert the RJ45 crystal head into the network
interface marked with ETH of the router and the device interface
respectively. Pay attention to the direction when inserting the cable.
Please insert the crystal head in place.
b) Power cable connection: Connect the Power output end of the adapterto
the Power port labeled Power of the device, and then connect the 220V
AC Power to the device for normal operation.
2. Configuring equipment
Configuring with JASMINER Group Control Software
Download the "IP Group Control Management Software" from the JASMINER website
→ Service → Firmware and Software → Other；
Install the sl_miner.exe program (IP group control management software) on a
Windows PC, double click on it and run it, note that the PC needs to be on the same
network segment as the device；
After successful installation as shown below, click on "Auto Generate" → "Start Scan"
in the software interface, the software will automatically pop up information about
the device after the scan is complete.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
9
Check the machines need to be configured
Copy and paste the obtained pool address into the pool, then copy and paste the
sub-account (worker) into the wallet/account number (if you do not have a
registered pool, you need to register for the pool first, refer to the pool registration
tutorial for details).

JASMINER X4 High-throughput Quiet Server Instruction
Manual
10
Select the algorithm, the device supports both ETH and ETC algorithms, with the
default being the ETH algorithm；
select the operating frequency, the default is 200 MHz；
clicking on Configure Miner to start the configuration；
Check the hash rate
After the device running for about 30 minutes, you will be able to view the
corresponding hash rate information.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
11
At this point the configuration of the high throughput server has been completed
and the machine can work normally.
3.Other settings: double click on the device in the group control software to enter
the web page for modification and setting.
*Up to now, all parameters have been set.
If you would like to know more about device setup you can read items 4 and 5.
4.Setup without IP group control management software.
Enter the shown IP address into the browser and press enter to open the device web
operation interface.
Default user name: root Default password: root

JASMINER X4 High-throughput Quiet Server Instruction
Manual
12
Enter the "miner" configuration interface to modify the ore pool settings and let
the device start to provide hashate for you.
Enter the preferred and two alternative mining pool addresses, account name
and password.
Select the algorithm. The device support both ETCHASH and ETHASH algorithm.
Default algorithm is ETCHASH.
Click "update" to submit the configuration.
View hashrate
After 30 minutes running, we can find device hashrate on Status page.
Configuration of this high-throughput server is complete.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
13
5.Other settings
IP setting: If you need to change the network configuration such as IP address,
select the "network" configuration item, and the device will dynamically obtain
the IP address by default. After the change, click "update" to take effect.
Modify login password: If you need to change the login name and password.
Select the "admin" configuration item. The default login name of the device is
root and the default password is root. After the change, click "update" to take
effect.
View log: If you want to view the log information of the system operating. You
can select the "log" option.

JASMINER X4 High-throughput Quiet Server Instruction
Manual
14
Upgrade system firmware: Select the "upgrade" option, select the firmware to be
upgraded, and click "upload image" to complete the upgrade operation.
Restart the device: Select "reboot" and click "reboot now".

JASMINER X4 High-throughput Quiet Server Instruction
Manual
15
Restore the device to the factory settings, select "reset", and click "reset now".