Sunmi Blink User manual
1
Table of Contents 目 录
SET DEFAULT PARAMETER 设置默认参数.................................................................................................................... 4
Factory Default Configuration 出厂默认配置 .................................................................................................... 4
INTERVAL TIME 识读间隔时间 ........................................................................................................................................ 4
BEEPER VOLUME 蜂鸣器音量 ........................................................................................................................................ 4
BEEP AFTER GOOD DECODE 解码成功提示声 ............................................................................................................. 5
TERMINATOR 结束符设置 ............................................................................................................................................... 5
LED AFTER GOOD DECODE 解码成功提示灯 ............................................................................................................... 6
MUTE 静音 ....................................................................................................................................................................... 7
BOOT PROMPT 开机提示音 ............................................................................................................................................. 7
SETUP CODE PROMPT 设置码参数提示音 .................................................................................................................... 7
PREFIX/SUFFIX VALUES 前缀/后缀值 ............................................................................................................................ 8
SCAN DATA TRANSMISSION FORMAT 数据传输格式 .................................................................................................... 8
COMMUNICATION MODE 通信方式 ............................................................................................................................... 10
SENSITIVITY LEVEL 灵敏度等级 ................................................................................................................................... 10
STABILITY OF INDUCTION TIME 稳定感应时间 ............................................................................................................. 11
OUTPUT INTERVAL OF THE SAME CODE 相同读码延时 .............................................................................................. 11
OUTPUT PRODUCT INFORMATION 输出产品信息......................................................................................................... 12
OUTPUT CHARACTER SET TYPE 输出字符集类型....................................................................................................... 12
INPUT CHARACTER SET TYPE 输入字符集类型 .......................................................................................................... 13
USB TYPE USB 类型 ................................................................................................................................................. 14
KEYBOARD 键盘 .......................................................................................................................................................... 14
Country/Language Keyboard 国家/语言键盘布局选择 .................................................................................. 14
Time interval that keyboard outputs character 键盘输出字符时间间隔 ...................................................... 16
Quick Settings of Keyboard Output Time Interval 键盘输出时间间隔快速设置 ......................................... 17
Letter case conversion 键盘输出强制字母大小写转换 .................................................................................. 17
Keyboard Type 键盘类型 ................................................................................................................................... 18
BARCODE GLOBAL SWITCH 条码全局开关 .................................................................................................................. 18
1D Global Switch 一维码开关 .......................................................................................................................... 19
2D Global Switch 二维码开关 ........................................................................................................................... 19
All Barcode Switch 全部条码开关 ..................................................................................................................... 20
UPC/EAN ...................................................................................................................................................................... 21
Enable/Disable UPC-A 使能/禁止 UPC-A ....................................................................................................... 21
Enable/Disable UPC-E 使能/禁止 UPC-E ...................................................................................................... 21
Enable/Disable EAN-8 使能/禁止 EAN-8 ......................................................................................................... 21
Enable/Disable EAN-13 使能/禁止 EAN-13 .................................................................................................. 22
Enable/Disable Bookland EAN(ISBN) 使能/禁止 Bookland EAN(ISBN) .................................................... 22
Decode UPC/EAN Supplementals UPC/EAN 附加码 ................................................................................... 22
Transmit UPC-A Check Digit 传输 UPC-A 校验位 ......................................................................................... 23
Transmit UPC-E Check Digit 传输 UPC-E 校验位 ......................................................................................... 23
UPC-A Preamble UPC-A 前导码 ................................................................................................................... 24
UPC-E Preamble UPC-E 前导码 ..................................................................................................................... 25
Convert UPC-E to UPC-A 转换 UPC-E 为 UPC-A ...................................................................................... 25
EAN-8 Zero Extend EAN-8 零扩展 ................................................................................................................ 26
Bookland ISBN Format Bookland ISBN 格式 ................................................................................................. 26
UPC/EAN Security Level UPC/EAN 安全级别 ............................................................................................... 27
CODE 128 ...................................................................................................................................................................... 28
Enable/Disable Code 128 使能/禁止 Code 128 ............................................................................................. 28
Enable/Disable GS1-128 (formerly UCC/EAN-128)使能/禁止 GS1-128（原 UCC/EAN-128） .............. 28
Enable/Disable ISBT 128 使能/禁止 ISBT 128 .............................................................................................. 29
Lengths for Code 128 Code 128 的长度 ......................................................................................................... 29
CODE 39 ........................................................................................................................................................................ 29
2
Enable/Disable Code 39 使能/禁止 Code 39 .................................................................................................. 29
Set Lengths for Code 39 Code 39 长度设置 ................................................................................................ 30
Code 39 Check Digit Verification Code 39 校验位验证 ................................................................................. 31
Transmit Code 39 Check Digit 传输 Code 39 校验位 ................................................................................... 31
Enable/Disable Code 39 Full ASCII 使能/禁止 Code 39 Full ASCII ........................................................... 32
Code 39 Transport Start Character and Terminator Code 39 传送起始符与终止符 ............................ 32
Convert Code 39 to Code 32 (Italian Pharma Code) 转换 Code 39 为Code 32（意大利医药码） ...... 33
Code 32 Prefix Code 32 前缀 ........................................................................................................................ 33
CODE 93 ........................................................................................................................................................................ 34
Enable/Disable Code 93 使能/禁止 Code 93 .................................................................................................. 34
Set Lengths for Code 93 设置 Code 93 长度 ............................................................................................... 34
CODE 11 ........................................................................................................................................................................ 35
Enable/Disable Code 11 .................................................................................................................................... 35
Set Lengths for Code 11 Code 11 长度设置 ................................................................................................... 36
Code 11 Check Digit Verification Code 11 校验码验证 ................................................................................. 37
Transmit Code 11 Check Digits 传输 Code 11 校验位 ................................................................................. 37
INTERLEAVED 2 OF 5/ITF/交叉 25 码 ........................................................................................................................... 38
Enable/Disable Interleaved 2 of 5 使能/禁止 Interleaved 2 of 5 ................................................................... 38
Set Lengths for Interleaved 2 of 5 Interleaved 2 of 5 长度设置 ................................................................... 38
I 2 of 5 Check Digit Verification I 2 of 5 校验码验证 ..................................................................................... 39
Transmit I 2 of 5 Check Digit 传输 I 2 of 5 校验位 ......................................................................................... 40
Convert I 2 of 5 to EAN-13 转换 I 2 of 5 为EAN-13 ..................................................................................... 40
DISCRETE 2 OF 5/INDUSTRIAL 2 OF 5/IND25/工业 25 码 ............................................................................................ 41
Enable/Disable Discrete 2 of 5 使能/禁止 Discrete 2 of 5 ............................................................................. 41
Set Lengths for Discrete 2 of 5 Discrete 2 of 5 长度设置 .............................................................................. 41
MATRIX 25(矩阵 25) ..................................................................................................................................................... 43
Enable/Disable Matrix 25 使能/禁止 Matrix 25 ............................................................................................... 43
Matrix 25 Check Digit Verification Matrix 25 校验位验证 .............................................................................. 43
Transmit Matrix 25 Check Character 传输 Matrix 25 校验字符 .................................................................... 43
Set Lengths for Matrix 25 Matrix 25 长度设置 ............................................................................................. 44
STANDARD 25/IATA 25(标准 25) ................................................................................................................................. 45
Enable/Disable Standard 25 使能/禁止 Standard 25 ..................................................................................... 45
Standard 25 Check Digit Verification Standard 25 校验位验证 ................................................................... 45
Transmit Check Character 传输校验字符 ........................................................................................................ 45
Set Lengths for Standard 25 Standard 25 长度设置 ................................................................................... 46
CODABAR ....................................................................................................................................................................... 47
Enable/Disable Codabar 使能/禁止 Codabar .................................................................................................. 47
Set Lengths for Codabar Codabar 长度设置 .................................................................................................. 47
NOTIS Editing NOTIS 编辑 ............................................................................................................................... 48
Start Character and Terminator 起始符与终止符格式 ................................................................................... 49
Letter Case Setting of Start Character and Teminator 起始符和终止符字母大小写的设置 .................... 49
MSI/MSI PLESSEY ..................................................................................................................................................... 50
Enable/Disable MSI 使能/禁止 MSI ................................................................................................................. 50
Set Lengths for MSI MSI 长度设置 ................................................................................................................ 50
MSI Check Digits MSI 校验位 ........................................................................................................................... 51
Transmit MSI Check Digit 传输 MSI 校验码 ................................................................................................... 52
MSI Check Digit Algorithm MSI 校验码算法 ................................................................................................... 52
GS1 DATABAR/RSS ..................................................................................................................................................... 53
Enable/Disable GS1 DataBar-14 使能/禁止 GS1 DataBar-14 .................................................................... 53
Enable/Disable GS1 DataBar Limited 使能/禁止 GS1 DataBar Limited ..................................................... 53
Enable/Disable GS1 DataBar Expanded 使能/禁止 GS1 DataBar Expanded ........................................... 53
PDF417 ......................................................................................................................................................................... 54
Enable/Disable PDF417 使能/禁止 PDF417 ................................................................................................... 54
3
Read Multi-code 识读多码 ................................................................................................................................. 54
Read Normal Phase/ Phase Reversal 正/反相识读 ...................................................................................... 55
QR ................................................................................................................................................................................. 55
Enable/Disable QR 使能/禁止 QR ................................................................................................................... 55
Read Multi-code 识读多码 ................................................................................................................................. 56
ECI Control ECI 控制 ....................................................................................................................................... 56
DATA MATRIX(DM) ........................................................................................................................................................ 56
Enable/Disable Data Matrix(DM) 使能/禁止 Data Matrix(DM) ..................................................................... 56
Read Multi-code 识读多码 ................................................................................................................................. 57
Read Normal Phase/ Phase Reversal 正/反相识读 ....................................................................................... 57
ECI Control ECI 控制 ....................................................................................................................................... 58
MAXI CODE .................................................................................................................................................................... 58
Enable/Disable Maxi Code 使能/禁止 Maxi Code .......................................................................................... 58
AZTEC CODE .................................................................................................................................................................. 59
Enable/Disable Aztec Code 使能/禁止 Aztec Code ....................................................................................... 59
HAN XIN CODE ............................................................................................................................................................... 59
Enable/Disable Han Xin Code 使能/禁止 Han Xin Code ............................................................................... 59
Read Multi-code 识读多码 ................................................................................................................................. 59
Read Normal Phase/ Phase Reversal 正/反相识读 ....................................................................................... 60
ISSN .............................................................................................................................................................................. 60
PLESSEY ..................................................................................................................................................................... 61
1.APPENDIX 附录 ................................................................................................................................................. 62
NUMERIC BAR CODES 数字设置码 .............................................................................................................................. 62
CANCEL 取消条形码 .................................................................................................................................................... 63
4
Set Default Parameter 设置默认参数
To restore Factory Default Configuration, scan the appropriate bar code below.
可以通过扫描以下设置码恢复为出厂默认配置
Factory Default Configuration 出厂默认配置
(0x00)
Note: Default configurations of the scan engine depend on factory default configuration.
注：识读引擎的默认配置由实际出厂的配置信息决定。
Interval Time 识读间隔时间
The interval time between two readings in continuous mode. Regardless of the last success or failure to
read, more than the specified time will automatically trigger the next reading.
Default: 500ms,unit: 100ms,range: 0-9900ms
To set a Interval Time, scan the bar code below. Next scan two Numeric Bar Codes in appendix that
correspond to the desired time-out. Single digit values must have a leading zero. For example, to set a
time-out of 0.5 seconds, scan the bar code below, then scan the “0” and “5” bar codes. To change the
selection or cancel an incorrect entry, scan Cancel in appendix..
连续模式下两次识读间的间隔时间。不论上次识读成功或失败，超过该时间自动进入下次识读。
默认：500ms，单位：100ms，范围：0-9900ms
为了设置识读间隔时间，扫描下面的条码。接下来扫描附录中的两个
数字设置码
来对应所需的超时。不足位
用0补齐。例如，设定0.5秒的超时，扫描下面的条码，然后扫描“0”和“5”的条形码。改变选择或者取消不正确的
输入设置，扫描附录中的
取消条形码
。
Interval Time
(Default: 500ms.)
识读间隔时间
(默认: 500ms.)
Beeper Volume 蜂鸣器音量
To select a decode beep volume, scan the appropriate bar code.
扫描以下相应的条码，设置蜂鸣器音量。
Low 低
(0x02)
5
Medium 中
(0x01)
*High 高
(0x00)
Beep After Good Decode 解码成功提示声
Scan this symbol to set the scan engine to beep after a good decode.
扫描以下条码设置当识读引擎解码成功时发出成功的提示声。
*Beep After Good Decode解码成功提示声
(0x01)
Scan this symbol to set the scan engine not to beep after a good decode. The beeper still operates
during parameter menu scanning and indicates error conditions.
扫描以下的条形码设置识读引擎解码成功后不发出提示声。蜂鸣器仍在参数菜单扫描期间工作，并指示
错误条件。
Do Not Beep After Good Decode解码成功无提示声
(0x00)
Terminator 结束符设置
Add character format: Decode Data+Terminator.
结束字符是在解码数据后面添加字符格式: 解码数据+结束字符。
*禁止 Disable
(0x00)
6
# &回车换行 CR LF
(0x01)
%回车 CR
(0x02)
跳格 TAB
(0x03)
回车回车 CR CR
(0x04)
回车换行回车换行 CR LF CR LF
(0x05)
LED After Good Decode 解码成功提示灯
To enable or disable LED after good decode, scan the appropriate bar code below.
解码成功指示灯亮一定的时间，前提是指示灯作为解码指示使用。
禁止 Disable
(0x00)
7
*使能 Enable
(0x01)
Mute 静音
To enable or disable close all prompt, scan the appropriate bar code below.
使能或者禁止关闭全部提示音，扫描以下相应的条码。
*禁止 Disable
(0x00)
使能 Enable
(0x01)
Boot prompt 开机提示音
禁止 Disable
(0x00)
*使能 Enable
(0x01)
Setup Code Prompt 设置码参数提示音
禁止 Disable
(0x00)
8
*使能 Enable
(0x01)
Prefix/Suffix Values 前缀/后缀值
A prefix and/or one or two suffixes can be appended to scan data for use in data editing. To set these
values, scan a four-digit number (i.e. four bar codes) that corresponds to ASCII values. See the Table 1-1 and
Numeric Bar Codes in appendix. To change the selection or cancel an incorrect entry, scan Cancel in
appendix.
一个前缀和/或一个或两个后缀可以附加到扫描数据供数据编辑使用。设置这些值, 对应于ASCII值扫描一个
四位数(即四个条形码)。见
表
1-1和
数字设置码
。改变选择或取消一个不正确的设置，扫描附录中的
取消条形码
。
NOTE In order to use Prefix/Suffix values, the Scan Data Transmission Format must be set.
注：为使用前缀/后缀值，必须设置
扫描数据传输格式
。
Scan Prefix前缀
Scan Suffix 1后缀1
Scan Suffix 2后缀2
Data Format Cancel
取消数据格式
Scan Data Transmission Format 数据传输格式
To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the
desired format.
9
扫描以下相对应的条形码设置期望的数据传输格式。
*Data As Is
(0x00)
<DATA><SUFFIX 1>
(0x01)
<DATA><SUFFIX2>
(0x02)
<DATA> <SUFFIX 1><SUFFIX 2>
(0x03)
<PREFIX> <DATA >
(0x04)
<PREFIX> <DATA> <SUFFIX 1>
(0x05)
10
<PREFIX> <DATA> <SUFFIX 2>
(0x06)
<PREFIX> <DATA> <SUFFIX 1> <SUFFIX 2>
(0x07)
Communication Mode 通信方式
USB 串口 USB Serial Port
(0x02)
USB KBW+HID
(0x0E)
Sensitivity Level 灵敏度等级
Set automatic induction triggering sensitivity
Sensitivity Values Inquire the parameter values returned.
Special: 0,high: 1,Middle: 8,Low: 15, Default: High
设置自动感应触发的灵敏度
查询该参数返回的数值是灵敏度值，如:特:0，高:1，中:8，低:15。默认:高
特灵敏度 Special
(0x00)
11
*高灵敏度 High
(0x01)
中灵敏度 Middle
(0x02)
低灵敏度 Low
(0x03)
Stability of Induction Time 稳定感应时间
Stability of induction time, Default: 500ms, unit:100ms, range: 0-9900ms
进入检测环境前稳定的时间，默认：500ms，单位：100ms，范围：0-9900ms
稳定感应时间 Stability of Induction Time
For example:
Set stability of induction time is 200ms
Scan stability of induction time setting code,then scan Numeric Bar Codes 0 and 2
如：
设置稳定感应时间 200ms。
先扫描稳定感应时间设置码，再扫描
数字设置码
0和2。
Set stability of induction time is 1500ms
Scan stability of induction time setting code,then scan Numeric Bar Codes 1 and 5
设置稳定感应时间 1500ms
先扫描稳定感应时间设置码，再扫描
数字设置码
1和5。
Output Interval of The Same Code 相同读码延时
To avoid reading the same barcode multiple times in continuous mode and automatic induction mode, set
the scan engine to allow reading the same barcode after a delay.
Output interval of the same code is to refuse to read the same barcode within the set length of time.
Default: 500ms,unit:100ms,range: 0-9900ms
To set output interval of the same code, scan the bar code below. Next scan two Numeric Bar Codes in
appendix that correspond to the desired time-out. Single digit values must have a leading zero. For example,
to set a time-out of 0.5 seconds, scan the bar code below, then scan the “0” and “5” bar codes. To change the
selection or cancel an incorrect entry, scan Cancel in appendix.
12
为避免在连续模式和自动感应模式中同一条码被连续识读多次，可以要求识读引擎在延时设定时长后才允许
识读相同条码。
相同读码延时，是指读到一个条码后，在设定的时长内，拒读同一条码。只有在超过时长后，才可以识读并
输出。默认：500，单位：100ms，范围：0-9900ms
为了设置相同读码延时，扫描下面的条码。接下来扫描附录中的两个
数字设置码
来对应所需的超时。不足位
用0补齐。例如，设定 0.5 秒的超时，扫描下面的条码，然后扫描“0”和“5”的条形码。改变选择或者取消不正确
的输入设置，扫描附录中的
取消条形码
。
相同读码延时 Output Interval of The Same Code
For example:
Set output interval of the same code is 200ms
Scan output interval of the same code setting code,then scan Numeric Bar Codes to set 0 and 2
如：
设置相同读码延时 200ms。
先扫描相同读码延时设置码，再扫描
数字设置码
0和2。
Set output interval of the same code is 1500ms
Scan output interval of the same code setting code,then scan Numeric Bar Codes 1 and 5
设置相同读码延时 1500ms
先扫描相同读码延时设置码，再扫描
数字设置码
1和5。
Output Product Information 输出产品信息
Output Character Set Type 输出字符集类型
0: Primitive Type
1:GBK(GB2312)
2: UTF8
Default: 0(Primitive Type)
0:原始类型,
1:GBK(GB2312)
2:UTF8
默认:0(原始类型)
*Primitive Type 原始类型
(0x00)
13
GBK(GB2312)
(0x01)
UTF8
(0x02)
Input Character Set Type 输入字符集类型
*AUTO
(0x00)
GBK(GB2312)
(0x01)
UTF8
(0x02)
ASCII
(0x03)
14
USB Type USB 类型
USB type,0: USB1.1(Full Speed), 1:USB2.0(High Speed),Default USB1.1
USB 类型,0:USB1.1(全速),1:USB2.0(高速),默认 USB1.1
*USB1.1(全速)
*USB1.1(Full Speed)
(0x00)
USB2.0(高速)
USB2.0(High Speed)
(0x01)
Keyboard 键盘
Country/Language Keyboard 国家/语言键盘布局选择
*American Keyboard *美式键盘
(0x01)
Belgium 比利时
(0x02)
Denmark 丹麦
(0x06)
15
Finland 芬兰
(0x07)
France 法国
(0x08)
Austria、Germany 奥地利、德国
(0x09)
Italy 意大利
(0x0D)
Norway 挪威
(0x10)
Portugal 葡萄牙
0x12
Russia 俄罗斯
16
(0x14)
Spain 西班牙
(0x16)
Sweden 瑞典
(0x17)
Turkey_F 土耳其_F
(0x19)
Turkey_Q 土耳其_Q
(0x1A)
England 英国
(0x1B)
Japan 日本
(0x1C)
Time interval that keyboard outputs character 键盘输出字符时间间隔
Time interval that keyboard outputs character, range: 0-1000ms,unit: 5ms,default: 5ms
键盘输出字符间隔,范围 0-1000ms,单位:5ms,默认:5ms
17
For example:
Time interval: 100ms
First scan the setting code above,then scan ‘0’, ‘2’, ‘0’ numeric barcodes in order.
如:
设置输出时间间隔为:100ms
先扫描键盘输出字符时间间隔设置码,再按顺序扫描数字设置码 0、2、0。
Quick Settings of Keyboard Output Time Interval 键盘输出时间间隔快速设置
0ms
(0x00)
10ms
(0x01)
50ms
(0x02)
Letter case conversion 键盘输出强制字母大小写转换
If set to "Case Inversion", the uppercase of the output data will be lowercase, lowercase letters will be
uppercase; If set to "all uppercase", regardless of whether the letters in the output data are uppercase or
lowercase, all converted to uppercase letters; If set to "all lowercase", regardless of whether the letters in the
output data is uppercase or lowercase, all converted to lowercase letters.
若设置为“大小写反转”，则输出数据中大写字母将变为小写，小写字母变为大写；若设置为“全为大写”，则
无论输出数据中字母是大写还是小写，全部转换为大写字母；若设置为“全为小写”，则无论输出数据中字母是大
写还是小写，全部转换为小写字母。
*Normal Letter Case *字母大小正常
(0x00)
18
All Uppercase 字母全部转化为大写
(0x01)
All Lowercase 字母全部转化为小写
(0x02)
Case Inversion 字母大小写反相
(0x03)
Keyboard Type 键盘类型
Enable virtual keyboard, you can output the correct data in any keyboard language mode.When using
virtual keyboard, you must ensure that the keypad keys are valid
使能虚拟键盘后，可以在任何键盘语言模式下输出正确的数据。使用虚拟键盘时，必须确保小键盘数字键使
能有效。
Standard Keyboard*标准键盘
(0x00)
Virtual Keyboard 虚拟键盘
(0x01)
禁止 KBW 功能键
Parameter # 0xF2 0xC4
19
禁止 Disable
(0x00)
*使能 Enable
(0x01)
Barcode Global Switch 条码全局开关
1D Global Switch 一维码开关
Disable 禁止
(0x00)
Enable 使能
(0x01)
2D Global Switch 二维码开关
Disable 禁止
(0x00)
Enable 使能
(0x01)
20
All Barcode Switch 全部条码开关
Disable 禁止
(0x00)
Enable 使能
(0x01)
Table of contents
Other Sunmi Scanner manuals
